Table of Contents
Advertisement
www.ti.com
Reference
Header to disconnect AVCC from VCC supply. Connect an ampere meter to measure current flowing into the
JP16
analog domain.
VCC header. Can be used to observe device VCC when supplied by the debug probe or to feed in external
J7
power.
1.2.5.1
Bill Of Materials
Table 1-5
lists the bill of materials for the MSP-TS432PZ100.
Pos.
Ref Des. No.
1
PCB
2
C1, C2
3
C8, C9
4
C3
C4, C6, C10, C13,
5
C14
6
C5
7
C7, C11, C15, C16
8
C12
9
D1
10
D2
11
D3
12
R1
13
R2, R3,
14
R5, R6, R7, R8, R9
15
L1
16
R12, R13, R15
17
R4
18
R10, R11
19
R14
20
R16
R17, R18, R19,
21
R20, R21, R22, R23
JP1, JP2, JP9, JP7,
22
JP16
23
JP8, JP12, JP15
24
JP10, JP11
25
J1
JP3, JP4, JP5, JP6,
26
JP14
27
J2, J7
28
J3, J4, J5, J6
SLAU571A – March 2015 – Revised May 2016
Submit Documentation Feedback
Table 1-4. Important Board Components (continued)
Table 1-5. MSP-TS432PZ100 Bill Of Materials
No. Per
Description
Board
1
95.0 x 100.0 mm
2
12pF, CSMD0805
2
22pF, CSMD0805
1
10uF/10V, CSMD0805
5
100nF, CSMD0805
1
1.1nF, CSMD0805
4
1uF/10V, CSMD0805
1
4u7, CSMD0805
green LED, HSMG-C170,
1
DIODE0805
1
yellow LED, DIODE0805
1
red LED, DIODE0805
1
330R, 0805
2
330R, 0805
5
0R, 0805
1
4.7uH, 0806
3
0R, 0805
1
47k, 0805
2
4k7, 0805
1
47k, 0805
91kOhm, 0.1%, 25ppm/°C ,
1
0805
7
27R, 0805
4
2-pin header, male, TH
3
2-pin header, male, TH
2
2-pin header, male, TH
1
3-pin header, male, TH
5
2x2-pin header, male, TH
2
3-pin header, male, TH
4
25-pin header, TH
Copyright © 2015–2016, Texas Instruments Incorporated
Description
Digi-Key Part No.
"MSP-TS432PZ100" Rev.
1.1
1276-1120-1-ND
490-3608-1-ND
490-1709-2-ND
490-1666-1-ND
490-1623-2-ND
490-1702-2-ND
445-1370-1-ND
516-1434-1-ND
541-330ATR-ND
541-330ATR-ND
541-0.0ATR-ND
490-4044-1-ND
541-0.0ATR-ND
541-47KATR-ND
541-4.7KATR-ND
541-47KATR-ND
P91KDACT-ND
541-27ATR-ND
SAM1035-02-ND
SAM1035-02-ND
SAM1035-02-ND
SAM1035-03-ND
SAM1034-02-ND
SAM1035-03-ND
SAM1029-25-ND
MSP-TS432PZ100
Comment
2 layers, green solder mask
DNP
DNP
DNP
DNP
DNP
Murata
DNP
place jumper on header
not jumpered
DNP, keep pads free of
solder
place jumpers on pins 1-2
DNP: Headers are enclosed
in kit. Keep vias free of
solder.
13
Hardware
Advertisement
Table of Contents
