Advertisement
Quick Links
1.
PRECAUTIONS FOR SAFETY AND USE _____________________ 20
2.
INSTALLING THE OVEN __________________________________ 22
3.
DESCRIPTION OF CONTROLS ____________________________ 24
4.
USING THE OVEN _______________________________________ 25
5.
CLEANING AND MAINTENANCE ___________________________ 31
6.
EXTRAORDINARY MAINTENANCE _________________________ 33
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified engineer who is to install, commission and test the appliance.
INSTRUCTIONS FOR THE USER: these provide recommendations for
use, a description of the controls and the correct procedures for cleaning
and maintaining the appliance.
Table of Contents
19
Advertisement
Related Manuals for Smeg ALFA41XE
Summary of Contents for Smeg ALFA41XE
-
Page 1: Table Of Contents
Table of Contents PRECAUTIONS FOR SAFETY AND USE _____________________ 20 INSTALLING THE OVEN __________________________________ 22 DESCRIPTION OF CONTROLS ____________________________ 24 USING THE OVEN _______________________________________ 25 CLEANING AND MAINTENANCE ___________________________ 31 EXTRAORDINARY MAINTENANCE _________________________ 33 INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is to install, commission and test the appliance. -
Page 2: Precautions For Safety And Use
1. PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE. WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN. - Page 3 SHOULD ALWAYS BE WORN. THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE BACK OF THE OVEN. THIS NAMEPLATE MUST NEVER BE REMOVED. THE APPLIANCE IS INTENDED FOR PROFESSIONAL USE BY TRAINED STAFF.
-
Page 4: Installing The Oven
The use of reductions, adapters or junctions is not recommended. 2.1.1 Safety thermostat The oven is fitted with a safety device tripped in case of a serious malfunction. To reset the safety device, call the after-sales service. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance. - Page 5 Instructions for the Installer Levelling Level the oven by means of its four adjustable feet. To make the adjustment, undo the lock-nut and unscrew the foot. The adjuster screw travel is 10 mm. 2.3 Steam vent pipe The rear of the oven is fitted with a pipe which vents the steam produced during cooking.
-
Page 6: Description Of Controls
Instructions for the User 3. DESCRIPTION OF CONTROLS START BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, scroll through the preset programs and start cooking cycles. STOP BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure, edit... -
Page 7: Using The Oven
Instructions for the User 4. USING THE OVEN Precautions and General Advice When the oven is used for the first time, it should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process. - Page 8 Instructions for the User Program selection This oven has 10 different cooking programs, including: 5 preset programs (P1 to P5); 3 user-editable programs for fan-mode cooking (P6 to P8), 1 preheating program with user-editable temperature and start and end time (P9), 1 "easy"...
- Page 9 10 minutes, after which it will start to drop for a period up to a maximum time of 20 minutes, counted from when the beep sounded. After this the oven switches off. During this stage, the display shows the parameters of the selected program).
- Page 10 Instructions for the User The display shows "- - - - " to indicate that there are no cooking parameters present. Press START or keep it pressed to increase the preheating temperature; each time START is pressed the temperature increments by 5°C (from 30° to 300°).
- Page 11 Setting "programmed preheating" The first step is to make sure that the oven's main clock is set to the correct time; if not, set it as described in "SETTING THE TIME".
- Page 12 If the above parameters are set correctly, and only if the knob is set on P9, the oven will run the preheating program every day at the set time; during the preheating the display will show the "PrEh" message, and...
-
Page 13: Cleaning And Maintenance
Instructions for the User 5. CLEANING AND MAINTENANCE Important: never point jets of water straight at the oven and do not use high- pressure water cleaners. Before carrying out any operation, disconnect the oven from the electricity supply. 5.1 Cleaning stainless steel To keep stainless steel in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. - Page 14 Instructions for the User Cleaning the inside of the oven To keep the oven in good condition, it must be cleaned regularly at the end of each day, after allowing it to cool. Remove all removable parts. Remove the side runners by unscrewing the ring-nut A and extract them through the hole in the rear B.
-
Page 15: Extraordinary Maintenance
Instructions for the User 6. EXTRAORDINARY MAINTENANCE Occasionally, the oven will require minor servicing procedures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. - Page 16 B. The door can only be closed in the normal way. Oven door gasket To allow thorough cleaning of the oven, the door gasket can be removed. Before removing the gasket, remove the oven door as described above. Once the door has been removed, lift the tangs at the corners as shown on the right.