Page 3
75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 Page 3 of 16 Page 3 of 16 Page 3 of 16...
Page 4
The sensor carries out a 3D object analysis and detects depending on height, width, depth, direction, and speed. Page 4 of 16 Page 4 of 16 Page 4 of 16 Page 4 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 5
Lock the cover by turning the lock fastening the angle lock screw. horizontally and close it as screw clockwise. indicated. 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 Page 5 of 16 Page 5 of 16...
Connect the wires accordingly. The output functions can be configured if necessary (see page 10). Page 6 of 16 Page 6 of 16 Page 6 of 16 Page 6 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 7
2. Rotate the sensor in order to align the center of the red spots with the center of the door. Push OK. 3. Rotate the sensor until the LCD screen validates the position. Push OK to exit. Lock the sensor position by tightening the angle lock screw (see page 4). 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 8
Displayed value = Factory value Value Displayed value = Saved value Value Page 8 of 16 Page 8 of 16 Page 8 of 16 Page 8 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 9
OUT2 OUT2 OUT2 - Motion+ and Height Trigger - Motion+ and Speed Trigger - Motion+ and Height Trigger 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 Page 9 of 16 Page 9 of 16 Page 9 of 16...
Page 10
An object > 6" is detected during10 min (adjustable). An object > 1’6" is detected infinitely (not adjustable). Page 10 of 16 Page 10 of 16 Page 10 of 16 Page 10 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 11
+ 1 m of bidirectional detection in front of door) unidirectional detection (approaching in any direction; UNIDIRECTIONAL distance between object and sensor decreases) 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 Page 11 of 16...
Page 12
After 1 minute, the sensor flashes 5x orange. Push UNLOCK + LOCK ( )to exit the adjustment mode. Page 12 of 16 Page 12 of 16 Page 12 of 16 Page 12 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 13
(factory default is bold/underlined) NOTE: Each of these available parameters is slower than XX mph. I.e. If the parameter 15.5 is chosen, the sensor will detect objects moving at speeds SLOWER than 15.5 mph. 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
Page 14
To delete a trace, simply relaunch a walk teach-in and clear the respective detection zone for 15 seconds. Page 14 of 16 Page 14 of 16 Page 14 of 16 Page 14 of 16 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821...
1 minute. Motion detection Negative angle is too large Reduce angle of the sensor. starts too late 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 75.5916.03 LZR-WIDESCAN 20180821 Page 15 of 16 Page 15 of 16...
BEA strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory- trained for the type of door/gate system.