Share large files at faster network speeds, with maximum efficiency User Manual 16-Port Gigabit Switch 24-Port Gigabit Switch ����� ������� �� ��������� F5D5141-16 F5D5141-24...
Introduction Congratulations on your purchase of this high-quality Belkin 16- or 24-Port Gigabit Switch. Backward-compatible with 10/100 networks, each Switch easily integrates into a new or existing network for instant high performance. It delivers dedicated 100Mbps links to each directly attached LAN segment or PC, enabling your servers and workstations to transfer large AV and graphic files efficiently throughout your network.
Getting to Know your Switch Front-Panel LEDs Belkin 16- or 24-Port Gigabit Switches feature two rows of LEDs that provide information about connection speed, link/activity, plus a separate Power LED. ���������������������� (a) Power (POWER) LED • Green – Power on, normal operation •...
10Base-T, 100Base-Tx, and 1000Base-T network devices. Connect the power cord into the power socket in the rear of the Switch; now plug the other end of the power cord into a power source (wall jack or power strip).
Page 8
Connecting your Switch to another Switch Connect a Category 5e or 6 cable between one of the numbered ports on the front of the Switch and one of the numbered ports on the other Switch to which you are cascading or connecting.
This scheme ensures data integrity and provides a clean data stream. Sample Application This Switch is designed to operate as a small workgroup switch. It can provide 10-, 100-, or 1000Mbps connections to workstations, or 1000Mbps full-duplex links to high-speed servers. It can also provide...
The Switches can be placed on a flat surface or in a 19-inch rack. Placement on a Flat Surface Affix the four included rubber feet on the bottom of the Switch in the area that is clearly marked on each of the four corners.
Probable Causes Switch port, network card, or cable may be defective. Possible Solutions • Check that the Switch and attached device are both powered on. • Be sure the network cable is connected to both devices. • Verify that Category 5 or better cable is used for 10/100Mbps connections;...
877-736-5771. Technical support is available 24 hours a day, 7 days a week. Before you Call If possible, turn on your system before you call Belkin for technical assistance and call from a telephone at or near the computer. You may be asked to describe detailed information...
Information Information EMI Certification FCC Class A Certification (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 16
Information RFI Emission: • Limit class A according to EN 55022:1998, IEC 60601-1-2 (EMC, medical) • Limit class A for harmonic current emission according to EN 61000-3-2/1995 • Limitation of voltage fluctuation and flicker in low-voltage supply system according to EN 61000-3-3/1995 Immunity: •...
Page 17
Information Information Safety Compliance Please read the following safety information carefully before installing the Switch: Warning: Do not plug a phone-jack connector into the RJ45 port. This may damage this device. Warning: This product does not contain any user-serviceable parts.
Page 18
(except for shipping charges for the product). What is not covered by this warranty? All above warranties are null and void if the Belkin product is not provided to Belkin Corporation for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin Corporation determines that the Belkin product has been improperly installed, altered in any way, or tampered with.
Page 19
Belkin Corporation reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin Corporation for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin Corporation, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment.