Fig&#X97;2: Patriot Plus Rtx Battery Pack Installation - Ritron Patriot Plus RTX-454 Owner's Manual

Rugged professional two-way radios

Hide thumbs

Table Of Contents

BATTERIES

Belt Clip

Attachment Points

T AB

Battery Compartment

Battery Door (Top Edge)

NOTE: The battery door slides on and off

once the door latch is unlocked.

(See door latch above.) Lock this

latch after replacing the door.

FIG—2: PATRIOT PLUS RTX

BATTERY PACK

INSTALLATION

BATTERIES

Belt Clip

Attachment Points

T AB

All manuals and user guides at all-guides.com

NOTE: Install the battery AS SHOWN (left),

NOTE:

Install the battery (left) AS SHOWN,

with the battery label facing you,

with the battery label facing you right side up

right side up.

Charger Contacts

Slot: Two slots mate to the

Slot (Two slots mate to the battery

battery door top edge tabs.

door top edge tabs)

L o c

Door Latch

o c k

U n l

For assistance, call 800-USA-1-USA (800-872-1872)

NOTE: Install the battery AS SHOWN (left),

NOTE:

Install the battery (left) AS SHOWN,

with the battery label facing you,

with the battery label facing you right side up

right side up.

Charger Contacts

Slot: Two slots mate to the

Slot (Two slots mate to the battery

battery door top edge tabs.

door top edge tabs)

BELT CLIP

BELT CLIP INSTALLATION

The CBX-A belt clip is designed to

bend away rather than break, or

damage the radio case.

Remove the clip to bend it back to its

original shape. See the following

instructions to attach the CBX-A belt

clip to your RTX Plus radio. Refer to

FIG—2 at left.

1. Carefully remove the two peel-off

tabs located on the sides of the

label on the case back. Screw

holes are located under the tabs.

2. Place the belt clip on the radio

case back with the two screw

holes aligned with the holes in the

radio case. Secure the belt clip

with the included screws and

washers.

CAUTION: Use only the screws

included; longer screws

will damage radio

electronics.

If you later remove the

belt clip, reinstall the

screws and washers in

the case back to seal out

dirt and moisture.

BELT CLIP

BELT CLIP INSTALLATION

The CBX-A belt clip is designed to

bend away rather than break, or

damage the radio case.

Remove the clip to bend it back to its

original shape. See the following

instructions to attach the CBX-A belt

clip to your RTX Plus radio. Refer to

FIG—2 at left.

1. Carefully remove the two peel-off

tabs located on the sides of the

label on the case back. Screw

holes are located under the tabs.

2. Place the belt clip on the radio

case back with the two screw

holes aligned with the holes in the

radio case. Secure the belt clip

with the included screws and

washers.

RADIO CARE

OBSERVE CAUTION IN THE FOLLOWING

ENVIRONMENTS TO MAXIMIZE THE LIFE

OF YOUR RADIO EQUIPMENT:

MOISTURE: PATRIOT Plus SST Series radios are

not waterproof. DO NOT directly expose them to rain

or excessive moisture.

CHEMICALS: Detergents, alcohol, aerosol sprays or

petroleum products can damage the radio case. DO

NOT use petroleum solvents of any kind; use a soft

cloth moistened with water to clean the case.

EXTREME HEAT: High temperatures can damage

the battery and other components. DO NOT expose

the units to extreme heat or leave them in direct

sunlight.

LOW TEMPERATURES: The capacity of the NiCd

battery is greatly reduced in extreme cold. When

using the unit in very cold environments, periodically

warm the radio under your coat.

EXCESSIVE TRANSMISSIONS: Maximum drain on

battery power occurs when transmitting. DO NOT

hold the Push-To-Talk switch down longer than

necessary during transmission intervals. DO NOT

reduce battery service life by attempting to power a

radio with a depleted battery; always charge

batteries overnight after each day of use.

VIBRATION/ SHOCK: Although your PATRIOT Plus

radio is designed to be rugged, it will not survive

excessive abuse. Avoid dropping the radio.

NOTE: The optional MHX-A holster provides added

protection from weather and shock.