Grass trimmer to blade conversion for trimmer t242 (12 pages)
Summary of Contents for Shindaiwa 81642
Page 1
T231 TRIMMER T231X TRIMMER WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit. T231 T231X Part Number 81642 Rev. 11/06...
As an owner/operator, you’ll soon discover for yourself why Shindaiwa is simply in a class by itself! IMPORTANT! The information contained in this own- er's/operator's manual describes units available at the time of publication.
General Safety Instructions Work Safely Shindaiwa trimmers operate at very high speeds and can do serious damage or injury if they are misused or abused. Never allow a person without training or instruction to operate this unit! WARNING! Never make unauthorized attachment installations.
Safety Labels Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Figure 3 Make sure bystanders or observers outside the 50-foot “danger zone”...
Specifications T231 dry weight (less attachments) ...10.9 lb./4.9 kg T231X dry weight (less attachments) ...11.2 lb./5.1 kg Engine model ... Shindaiwa S230C Engine type ... 2-cycle, catylist, vertical-cylinder , air cooled Bore x stroke ... 1.26x1.10 in./32x28 mm Displacement ... 1.4 cu. in./22.5 cc Maximum power ...
Assembly and Adjustments This unit comes fully assembled with the exception of the cutting attachment shield and cutting attachment. Prior to Assembly Before assembling, make sure you have all the components required for a com- plete unit and inspect unit and compo- nents for any damage.
Page 7
Assembly: Trimmer Head Install the Trimmer Head. 1. Turn the trimmer over so that the gearcase output shaft faces UP. 2. Remove and discard the black plastic retaining plug from the output shaft.
Page 8
Assembly: Blade T231X Mount the Cutting Blade Turn the T231X upside down so the gearcase output shaft is facing UP and re- move the shaft bolt, bolt guard and holder B from the gearcase shaft. 1. Align the hole in blade holder A with the matching hole in the gearcase flange and then temporarily lock the output shaft by inserting...
Oil is a registered JASO FC classified oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions en- gines. Shindaiwa one also includes a fuel stabilizer. 1. Place the trimmer on a flat, level surface.
If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection. When the Engine Starts n After the engine starts, allow the en- gine to warm up at idle 2 or 3 minutes before operating the unit.
Checking Unit Condition Use only authorized Shindaiwa parts and ac- cessories with your Shindaiwa trimmer. Do not make modifications to this unit without written approval from Shindaiwa, Inc. WARNING! A cutting attachment shield or other protective device is no guarantee of protection against ric- ochet.
When cutting wood with a saw, feed the blade slowly—never strike or “slam” a spinning blade against the wood. WARNING! DO NOT use 2-tooth or non- Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters. O’Clock Blade Rotation OK To Cut Seven Five O’Clock...
DO NOT use 2-tooth or NON- Shindaiwa approved 4-tooth cutting blades on Shindaiwa trim- mers or brushcutters. n Blades are not interchangeable between Shindaiwa edgers and trimmer/brushcutter models.
Shindaiwa Tornado ® Blade To sharpen the cutters on a Shindaiwa Tornado Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.
Consult with an authorized servicing dealer. Refill with clean fresh unleaded gasoline with a pump octane of 87 or higher, mixed with Shindaiwa Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio. Replace fuel filter or vent as required. Restart.
Page 17
Consult with an authorized servicing dealer. Refill with clean fresh unleaded gasoline with a pump octane of 87 or higher, mixed with Shindaiwa Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio. Consult with an authorized servicing dealer. Consult with an authorized servicing dealer.
Page 18
Troubleshooting Guide (continued) Symptom Poor acceleration. Engine stops abruptly. Engine difficult to shut off. Cutting attachment rotates at engine idle. Excessive vibration. Cutting attachment will not rotate. ADDITIONAL PROBLEMS ADDITIONAL PROBLEMS Possible Cause Clogged air filter. Clogged fuel filter. Lean fuel/air mixture. Idle speed set too low.
California. For parts listed under PARTS COVERED, the dealer authorized by Shindaiwa Corporation will, at no cost to you, make the neces- sar y diagnosis, repair, or replacement of any defective emis- sion-related component to ensure that the engine complies with applicable U.S.
Page 25
Consulte arrancar. vuelva encendido posición interruptor encender. necesario; como presion combustible filtro Reemplace gasolina/aceite. proporción Shindaiwa tiempos motores para mezcla aceite mezclado superior octanaje plomo limpio fresco, combustible llenar autorizado. servicio agente Consulte vez. otra pruebe autorizado.
Page 26
Retire desemblaje. orden reversa forma silenciador ensamblar Vuelva Shindaiwa. autorizado distribuidor servicio centro consulte carbón, excesiva acumulación nota ¡IMPORTANTE! carbón. acumulación busca cilindro escape Inspeccione silenciador inferior Tornillo...
Page 27
PRECAUCION! figura Consulte combustible. tanque combustible Figura extraer para alambre gancho principal. estrias figura equivalente. Engranajes para Shindaiwa grasa como base grasa solamente usada grasa hasta nueva grasa introduzca caja costado alimentador tuerca Retire engranajes. collar corte...
Page 29
cintura. altura sobrepase disco permita nunca verticales, cortes efectuar ¡ADVERTENCIA! figura Consulte disco. rior infe- borde solamente corte corte, travéz abajo para arriba disco Mueva operario. hacia gire disco inferior borde forma suelo, respecto grados ángulo disco desmalezadora Sostenga Verticales Cortes Figura 1060...
Page 30
Entre cuando cabezal incluídas instrucciones Opere siem- consulte adecuada, operación NOTA: operacionales. otro específicas aplicaciones para cada Shindaiwa, cabeza- modelos varios equi- esté pueda Shindaiwa Máquinas – Césped figura operación. extensos periódos operador para comodiad puede hombro...
Page 31
Después quina. má- usar antes minutos ó mínima marcha caliente permita motor, arranque Después Motor Arranca Cuando inspección. Shindaiwa distribuidor podadora devuelva entronces aquí, descrito procedimiento ajustada mínima marcha mínima! marcha girar debe NUNCA corte accesorio ¡ADVERTENCIA! Mínima Marcha corte.
Page 32
Retire combustible. tapa alrededor despojos suciedad cualquier Retire nivelada. plana ficie super- sobre maquina Posicione combustible. estabilizador incluye tambien Shindaiwa emisión. baja Shindaiwa motores todo para recomendado Shindaiwa EGD. ISO-L- rendimiento requisitos excede cumple tambien clasificado JASO registrado aceite StaBil™...
Page 33
cuchilla. usada para lista ensamblada completamente ahora estar debe T231X 23115 claridad) muestra cuchilla ensamblaje Apriete hexago- salida Disco/Cuchilla Figura 23112 23111 seguridad lugar retén Centre disco Ponga Figura 23110 seguridad Retén salida descentrada posición seguridad retén Deslice hexagonal. llave Retire reloj.
Page 34
SP_7 cabezal. usada para lista ensamblada completamente estar ahora debe unidad Figura 23108 pagina). siguiente (consulte seguridad reten perno protector eje, perno retire primero T231X, cabezal instalar Para T231X 23107 hexago- firmemente. aprietelos tornillos Reinstale figura Consulte corte. cuchilla Gire capturadas.
Page 35
Figura allen cabeza Tornillos 23102 tora Protec- Barra Exterior Tubo mango. posicion Etiqueta Mango producto. este normal operación durante operador vista punto desde direcciones indican “trasera”, “delantera” “RH”, derecha”, “mano “derecha”, “LH”; izquier- “mano “izquierda”, términos ¡IMPORTANTE! trabadoras. tuercas figura Consulte mm).
Page 37
Esto operación. accesorio distancia metros) píes dentro esté nadie Asegurese volante. objeto golpeado transeúnte algún riesgo Reduzca Trabajo Figura Shindaiwa. Etiquetas faltantes. daños libres estén etas Seguridad Etiquetas Seguridad Etiquetas Figura lanzados Esté daños. busca corte cesorio inspeccione motor detenga sólido,...
Page 38
MEDICATION. DRUGS, ALCOHOL, ¡ADVERTENCIA! INFLUENCE UNDER TIRED, THIS OPERATE segura. maquina esta operar para condiciones optimas estar Alerta cortos. esta Shindaiwa accesorios autorizados. accesorios instale Nunca nivel ¡ADVERTENCIA! largo unidad esta opere entrenamien- persona Nunca abusadas. usadas lesiones daños causar...
Page 39
Inc. Shindaiwa comunicarse puede También gusto. atenderá quien Shindaiwa, distribuidor consulte manual, este contenida información alguna entiende T231 Serie relacionada pregunta alguna tiene área. vigentes leyes normas substituir propósito tienen condiciones mayoría bajo segura operación...
Page 40
11/06 Rev. 81642 parte Número máquina. esta opere cuando oídos ojos para protección Siempre contenido. familiaricese manual este otros! lesiones causar lesiones sufrir riesgo Disminuya ¡¡ADVERTENCIA! T231X T231 T231X/EVC Podadora T231/EVC Podadora Shindaiwa Propietario/Operador Manual...