Sherwood RV-4060R Operating Instructions Manual page 2

INTRODUCTION
UNPACKING AND INSTALLATION
Congratulations on Your Purchase!
Your new high fidelity Receiver is designed to deliver maximum
enjoyment and years of trouble free service.
Please take a few moments to read this manual thoroughly. It will
explain the features and operation of your unit and help ensure a trouble
free installation.
Please unpack your unit carefully. We recommend that you save the
carton and packing material. They will be helpful if you ever need to
move your unit and may be required if you ever need to return it for
service. Your unit is designed to be placed in a horizontal position and it
is important to allow at least two inches of space behind your unit for
adequate ventilation and cabling convenience.
To avoid early damage, never place the unit near radiators, in front of
heating vents, in direct sunlight, or in excessively humid or dusty
locations. Connect your complementary components as illustrated in the
following section.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage" within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Caution : Do not block ventilation openings or stack other
equipment on the top.
FOR U.S.A.
Note to CATV System Installer: This reminder is provided to call the
CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
CAUTION: Any changes or modifications in construction of this device
which are not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
2
READ THIS BEFORE OPERATING YOUR UNIT
FOR U.S.A. AND CANADA .................................... 120 V
FOR YOUR SAFETY
Units shipped to the U.S.A. and Canada are designed for
operation on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a nonpolarized
plug.
CAUTION : To prevent electric shock, match wide blade of plug
to wide slot, fully insert.
ATTENTION : Pour eviter les choc electriques, introduire la lame
la plug large de la borne correspondante de la prise et poussre
FOR AUSTRALIA AND EUROPE ............... 230 V/240 V
FOR YOUR SAFETY
Units shipped to Australia are designed for operation on 240 V
AC only.
To ensure safe operation, the three-pin plug supplied must be
inserted only into a standard three-pin power point which is
effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core
and be correctly wired to provide connection to earth.
Improper extension cords are a major cause of fatalities. The fact
that the equipment operates satisfactorily does not imply that the
power point is earthed and that the installation is completely
safe. For your safety, if in any doubt about the effective earthing
of the power point, consult a qualified electrician.
PAN-EUROPEAN UNIFIED VOLTAGE
All units are suitable for use on supplies 230-240 V AC.
FOR OTHER COUNTRIES ........................ 110 V/220 V
FOR YOUR SAFETY
Units shipped to countries other than the above countries are
equipped with an AC voltage selector switch on the rear panel.
Refer to the following paragraph for the proper setting of this
switch.
AC VOLTAGE SELECTION
This unit operates on 110-220 V AC. The AC voltage selector
switch on the rear panel is set to the voltage that
prevails in the area to which the unit is shipped. Before
connecting the power cord to your AC outlet, make sure that
the setting position of this switch matches your line voltage. If
not, it must be set to your voltage in accordance with the
following direction.
AC voltage selector switch
AC 110 V
Move switch lever to match your line voltage with a small
screwdriver or other pointed tool.
AC 220 V