Timer And Sleep Operation (Remote Control Only) - Sharp XL-DH229 Operation Manual

Setting the clock (continued)
5
To adjust the minutes, press the
then press the MEMORY button. Press the
button once to advance the time by 1 minute.
To confi rm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The "CLOCK" will appear or time will be displayed when the AC
power supply is restored after a power failure or unplugging the
unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" does not
appear in step 2, step 3 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programed contents. [Refer to "Factory reset,
clearing all memory" on page 14 for details.]
2
Perform "Setting the clock" from step 1 onwards.
Timer and sleep operation (Remote
control only)
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day that we
set. For example, set the timer as a wake-up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program, and
use the daily timer to wake up.
1 minute or more
Daily timer
Start
Stop
Timer playback
Before setting timer:
Check that the clock is set to the correct time (refer to
page 11-12). If it is not set, you cannot use the timer
function.
For timer playback: Plug in USB or load discs or dock iPod
to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
"ONCE SET" or "DAILY SET", and press the MEMORY
button. Set the clock to the correct time if "ONCE SET" or
"DAILY SET" does not appear.
4
Within 10 seconds, press the
"TIMER SET", and press the MEMORY button.
5
To adjust the hour, press the
the MEMORY button.
6
To adjust the minutes, press the
press the MEMORY button.
7
Set the time to fi nish as in steps 5 and 6 above.
8
To select the timer playback source (CD, TUNER, USB,
iPodor AUDIO IN), press the
MEMORY button.
or button and
or
Once timer
Start Stop
or button to select
or button to select
or button and then press
or button and then
or button. Press the
When you select the tuner, select a station by pressing the
or button, and then press the MEMORY button. If
a station has not been programmed, "NO PRESET" will be
displayed and timer setting will be cancelled.
9
Adjust the volume using the VOLUME control, and then press
the MEMORY button. Do not turn the volume up too high.
10
Press the ON/STAND-BY button to enter the power stand-by
mode. The "TIMER" indicator lights up and the unit is ready
for timer playback.
11
When the preset time is reached, playback will start. The
volume will increase gradually until it reaches the preset
volume. The " " indicator will blink during once timer
playback. The "DAILY" indicator will blink during daily timer
playback.
12
When the timer end time is reached, the system will enter the
power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every day. It will continue
until the daily timer setting is cancelled. Cancel the daily timer
when it is not in use.
Notes:
When performing timer playback using another unit
connected to the USB terminal or AUDIO IN socket, select
"USB" or "AUDIO IN" in step 8.
This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn on
or off. To stop the timer playback, follow step "Cancelling the
timer setting" of this page.
Checking the timer setting:
1
Turn the power on and press and hold down the CLOCK/
TIMER button.
2
Within 10 seconds, press the
"ONCE SET" or "DAILY SET", and press the MEMORY
button.
3
Within 10 seconds, press the
"TIMER CALL", and press the MEMORY button.
Canceling the timer setting:
1
Turn the power on and press and hold down the CLOCK/
TIMER button.
2
Within 10 seconds, press the
"ONCE SET" or "DAILY SET", and press the MEMORY
button.
3
Within 10 seconds, press the
"TIMER OFF", and press the MEMORY button. Timer will be
canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse
the same setting, perform the following operations.
1
Turn the power on and press and hold down the CLOCK/
TIMER button.
2
Within 10 seconds, press the
"ONCE SET" or "DAILY SET", and press the MEMORY
button.
3
Within 10 seconds, press the
"TIMER ON", and press the MEMORY button.
4
Press the ON/STAND-BY button to enter the power stand-
by mode.
E-12
or button to select
or button to select
or button to select
or button to select
or button to select
or button to select