Listening To The Radio; Setting The Clock (Remote Control Only) - Sharp XL-DH229 Operation Manual

Listening to the radio

Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the FUNCTION button on the main unit
or TUNER (BAND) button on the remote control
repeatedly to select the desired frequency band (FM
stereo, FM mono or AM).
3
Press the TUNING (
button to tune in to the desired station.
Manual tuning:
Press the TUNING (
button repeatedly to tune in to the desired station.
Auto tuning:
When the TUNING (
button is pressed for more than 0.5 seconds, scanning
will start automatically and the tuner will stop at the fi rst
receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may
stop automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING (
(TUNING ( or
To receive an FM stereo transmission:
Press the FUNCTION button on main unit or TUNER (BAND)
button on the remote control to select stereo mode and "ST"
indicator will be displayed. "
broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button
to extinguish the "ST" indicator. The reception changes to
monaural, and the sound becomes clearer.
Presetting a station
You can store 40 AM and FM stations in memory and
recall them at the push of a button. (Preset tuning)
1
Perform steps 1 - 3 in "Tuning".
2
Press the MEMORY button.
3
Within 30 seconds, press the PRESET (
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
or ) (TUNING (
or ) (TUNING ( or
or ) (TUNING (
)) button again.
" will appear when an FM
or
4
Within 30 seconds, press the MEMORY button to store
that station in memory. If the "MEMORY" and preset
number indicators disappear before the station is
memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change
a preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
To recall a preset station
1
Press the PRESET (
seconds to select the desired station.
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1
Press the PRESET (
0.5 seconds. The preset number will fl ash and the
programed stations will be tuned in sequentially, for 5
seconds each.
2
Press the PRESET (
desired station is located.
To erase entire preset memory
or ))
1
Press the POWER ON/STAND-BY button to enter the stand-
by mode.
2
While pressing down the FUNCTION button, press the POWER
))
ON/STAND-BY button until "TUNER CLEAR" appears.
or ))

Setting the clock (Remote control only)

or )
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button. Press
the
and then press the MEMORY button.
4
To adjust the hour, press the
) button
press the MEMORY button. Press the
once to advance the time by 1 hour. Hold it down to
advance continuously.
E-11
or ) button for less than 0.5
or ) button for more than
or ) button again when the
or button to select 12-hour or 24-hour display
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
or button and then
or button