Page 2
ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations. All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE CORPORATION or of their respective owners.
3.4.7 Configure the Port Trigger............... 3-32 3.5 Configure the DDNS..................3-33 3.6 Configure the SNTP ..................3-34 3.7 Configure the Port Binding ................3-35 3.8 Configure the Dynamic Routing................. 3-36 3.9 Configure the Mulitcast ..................3-37 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 4
6.4.1 Configure the Device Management............6-4 6.4.2 Upgrade Firmware..................6-5 6.4.3 Manage the User Configuration..............6-6 6.5 Configure the Mirror ................... 6-7 6.6 Configure the TR-069 ..................6-8 6.7 Manage the Log ....................6-10 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 5
6.8 Diagnosis ......................6-11 6.9 Check the ARP Table ..................6-14 6.10 Check the MAC Table ..................6-15 6.11 Configure the ETH Uplink Management ............6-16 6.12 Configure the IPv6 Switch ................6-16 Figures......................I Table .......................V SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 6
This page intentionally left blank. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Safety Precautions Warning! Before using the device, read the following safety precautions. ZTE bears no liability to the consequences incurred by violation of the safety instructions. Usage Cautions Read all the safety cautions carefully before using the device. Only use the accessories included in the package, such as power supply adapter and battery.
Page 8
If you need more information on collection, reuse and recycling systems, contact your local or regional waste administration. You may also contact your equipment provider for more information on the environmental performances of these products. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
1.1 Interfaces and Buttons The product is targeted to pvovide 24-hours continuous triple-play services, including VOIP. Figure 1-1 shows the interfaces and buttons on the back panel of the ZXHN H267N device. Figure 1-1 The Back Panel Table 1-1 describes the interfaces and buttons on the back panel and side panel of the ZXHN H267N device.
The USB interface is on a side of the ZXHN H267N. 1.2 Indicator Figure 1-2 shows the indicators on the front panel of the ZXHN H267N unit. Figure 1-2 The Front Panel Table 1-2 describes the indicators on the front panel of the ZXHN H267N unit.
The USB device is connected. Flashing Currently in data transmission. No USB device. 1.3 Cable Connection Figure 1-3 shows the devices that are connected to interfaces of the ZXHN H267N device. Figure 1-3 Cable Connection SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 12
ZXHN H267N Maintenance Management Guide This page intentionally left blank. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Table of Contents Configure TCP/IP .......................2-1 Login ..........................2-2 2.1 Configure TCP/IP To log in to the ZXHN H267N on a computer, you need to set the address of the computer to ensure that the address of the computer and the maintenance address of the ZXHN H267N are in the same network segment.
Steps 1. Open Internet explorer, and enter http://192.168.1.1 (default maintenance IP address of the ZXHN H267N) in the address field. Press the Enter key. The login page is displayed, see Figure 2-1. Figure 2-1 Login Page 2.
The section describes the status of Internet. The relevant information of Internet status is shown as below. Steps 1. On the main page of the ZXHN H267N, select Internet > Status > Ethernet to go to the Ethernet page. The page is shown in Figure 3-1.
ZXHN H267N Maintenance Management Guide Figure 3-1 Internet Status 2. (Option) on the main page of the ZXHN H267N, select Internet > Status > DSL , the relevant information is shown. 3. (Option) on the main page of the ZXHN H267N, select Internet > Status > 4in6 Tunnel , the relevant information is shown.
Chapter 3 Configure the Internet Steps 1. On the main page of the ZXHN H267N, select Internet > WAN > Ethernet to go to the Ethernet page, as shown in Figure 3-2. Figure 3-2 Ethernet Configuring page 2. Click The Creation & Configuration of Ethernet Connection.
Page 20
ZXHN H267N Maintenance Management Guide Table 3-1 Parameter Descriptions for the Route Mode Parameter Description To create a WAN connection, select Create WAN Connection. Connection Name To query or modify an existing connection, select the corresponding WAN connection. The connection type includes route and bridge connection.
Page 21
Range: 1–4094. To ensure normal service operation, the VLAN ID must be the same as that set in upper-layer OLT configuration. Bridge-based connection 5. Set the parameter Type to be Bridge connection. The Bridge-based connection page is displayed, seeFigure 3-4. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Figure 3-4 Bridge Page Table 3-2 lists the New Item parameters. Table 3-2 Parameter Descriptions for the Bridge Mode Parameter Description To create a WAN connection, select Create WAN Connection. Connection Name To query or modify an existing WAN connection, select the corresponding WAN connection.
The ZXHN H267N supports Route-based and Bridge-based WAN connections. Route-based connection Bridge-based connection Steps 1. On the main page of the ZXHN H267N, select Internet > WAN > DSL to go to the DSL page, as shown in Figure 3-5.
ZXHN H267N Maintenance Management Guide Figure 3-6 Route Page Table 3-3 lists the New Item parameters. Table 3-3 Parameter Descriptions for the DSL Parameter Description Connection Name Name of the connection. xDSL Transfer Mode There are two xDSL transfer modes: In the case of IPv4_PPPoE, select PTM.
Page 25
If xDSL Transfer ModeEnter is selected to be ATM, Transfer Type includes PPPoE and PPPoA. Username/Password PPPoE/PPPoA user name and password. They are provided by the ISP. Version version includes: IPv4 IPv6 IPv4/v6 In this case, IPv4 is selected. IPv4 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 26
Subnet Mask Subnet mask of ZXHN H267N. Gateway It is usually the IP address of the ZXHN H267N by default. DNS1–DNS3 IP address of the DNS server for static connections. You can set up to three IP addresses for the server. These IP addresses are provided by the ISP.
Service Type needs to be configured. ATM QoS used to limit the transmission of uplink traffic. The options are: CBR, RT-VBR, nRT-VBR, and UBR. If Service Type is selected to be CBR,RT-VBR or nRT-VBR, needs to be configured. 3-11 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 28
ZXHN H267N Maintenance Management Guide Parameter Description Sustainable Cell Rate. If Service Type is selected to be RT-VBR or nRT-VBR, SCR needs to be configured. Maximum Burst Size. If Service Type is selected to be RT-VBR or nRT-VBR, MBS needs to be configured.
3.2.3 Configure the 4in6 Tunnel Connection This page provides the parameters of 4in6 Tunnel configuration features. Steps 1. On the main page of the ZXHN H267N, select Internet > WAN > 4in6 Tunnel to go to the 4in6 Tunnel page, as shown in Figure 3-9.
3.2.4 Configure the 6in4 Tunnel Connection This page provides the parameters of 6in4 Tunnel configuration features. Steps 1. On the main page of the ZXHN H267N, select Internet > WAN > 6in4 Tunnel to go to the 6in4 Tunnel page, as shown in Figure 3-10.
Setting this parameter when 6in4 Tunnel Configuration is Static. 6rd Border Relay Address Setting this parameter when 6in4 Tunnel Configuration is Static. Tunnel Remote Address Setting this parameter when 6in4 Tunnel Type is Manual Tunnel. 3-15 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
The section describes how to configure global parameters. Steps 1. On the main page of the ZXHN H267N, select Internet > QoS > QoS Global Configuration to go to the QoS Global Configuration page. The page is shown in Figure 3-11.
Chapter 3 Configure the Internet Steps 1. On the main page of the ZXHN H267N, select Internet > QoS > Classification to go to the Classification page. 2. Click to create new Classification, the page as shown in Figure 3-12.
Page 34
ZXHN H267N Maintenance Management Guide Parameter Description Ingress Specify the data traffic direction. The Ingress option and Egress option cannot be the same. If the Ingress is LAN, the Egress should be a WAN or 3G connection. The data traffic direction is upstream.
This page provides the parameters of Congestion Management configuration features. Steps 1. On the main page of the ZXHN H267N, select Internet > QoS > Congestion Management to go to the Congestion Management page, as shown in Figure 3-13. Figure 3-13 Congestion Management Page...
3.3.4 Configure the QoS Traffic Policing This page provides the parameters of Traffic Policing configuration features. Steps 1. On the main page of the ZXHN H267N, select Internet > QoS > Traffic Policing to go to the Traffic Policing page, as shown in Figure 3-14.
Page 37
If VLAN is enabled, you can modify service priority through this parameter. Range: 0–7. A higher number indicates a higher priority. PeakRate Peak rate. PeakBurstSize Peak burst size. 2. Click Apply button to apply the changes. – End of Steps – 3-21 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
3.4.1 Configure the Firewall Level The section describes how to configure firewall level. Steps 1. On the main page of the ZXHN H267N, select Internet > Security > Firewall to go to the Firewall page, the page as shown in Figure 3-15.
3.4.2 Configure the Filter Criteria The section describes how to configure filter criteria. Steps 1. On the main page of the ZXHN H267N, select Internet > Security > Filter Criteria to go to the Filter Criteria page. Filter Switch & Mode Configuration 2.
ZXHN H267N Maintenance Management Guide Figure 3-17 MAC Filter Table 3-12 lists the Filter parameters. Table 3-12 Parameter Descriptions for the MAC Filter Parameter Description Name The name of the Filter. Type The type can be Bridge, Route, or Bridge and Route.
If the Ingress is LAN, the Egress should be a connection. The data traffic direction is upstream. If the Ingress is a connection, the Egress should be the LAN. The data traffic direction is downstream. 3-25 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
3.4.3 Configure the Local Service Control The section describes how to configure local service control. Steps 1. On the main page of the ZXHN H267N, select Internet > Security > Local Service Control to go to the Local Service Control page, as shown in Figure 3-20.
Service Control-IPv6 parameters. Table 3-15 Parameter Descriptions for the Service Control-IPv6 Parameter Description Name Name of the Service Control item. The name must be specified. Mode The mode includes the following: Allow and Discard. 3-27 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Parameter Description Ingress Specify the data stream inbound direction, and this parameter must be specified. If the Ingress is LAN, the data flow is upstream. If the Ingress is a WAN connection, the data flow is downstream.
The section describes how to configure ALG. ALG provides the relevant parameters of security configuration function. Steps 1. On the main page of the ZXHN H267N, select Internet > Security > ALG to go to the ALG page, the page as shown in Figure 3-23.
ZXHN H267N Maintenance Management Guide Figure 3-24 DMZ Configuration Page Table 3-17 lists the parameters. Table 3-17 Parameter Descriptions for the DMZ Parameter Description Switch Enable the host function. Connection connection type. Mapping Enable the mapping function. Host address of the computer or wireless devices at the side.
Chapter 3 Configure the Internet Steps 1. On the main page of the ZXHN H267N, select Internet > Security > Port Forwarding to go to the Port Forwarding page, the page as shown in Figure 3-25. Figure 3-25 Port Forwarding Configuration Page 2.
The port triggering is used to protect the ports. The system will not open these ports unless these ports are triggered. Steps 1. On the main page of the ZXHN H267N, select Internet > Security > Port Trigger to go to the Port Trigger page, the page as shown in Figure 3-26.
The section describes how to configure DDNS. DDNS provides the parameters of DDNS configuration function. Steps 1. On the main page of the ZXHN H267N, select Internet > DDNS to go to the DDNS page, the page as shown in Figure 3-27.
Chapter 3 Configure the Internet Steps 1. On the main page of the ZXHN H267N, select Internet > SNTP to go to the SNTP page, the page as shown in Figure 3-28. Figure 3-28 SNTP Configuration Page 2. Configure the SNTP parameters.
ZXHN H267N Maintenance Management Guide Steps 1. On the main page of the ZXHN H267N, select Internet > Port Binding to go to the Port Binding page,the page as shown in Figure 3-29. Figure 3-29 Port Binding Configuration Page 2. Select the WAN connection, and select the LAN port or SSID that you want to bind.
3. Click Apply button to apply the changes. – End of Steps – 3.9 Configure the Mulitcast 3.9.1 Configure the IGMP The section describes how to configure IGMP. IGMP provides the parameters of IGMP configuration features. 3-37 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. On the main page of the ZXHN H267N, select Internet > Multicast > IGMP to go to the IGMP page. The page is shown in Figure 3-31. Figure 3-31 IGMP Configuration Page 2. Enable the IGMP functions.
The section describes how to configure MLD. MLD provides the parameters of configuration features. Steps 1. On the main page of the ZXHN H267N, select Internet > Multicast > MLD to go to the MLD page. The page is shown in Figure 3-33.
The section describes the status of Local Network. The relevant information of Local Network status is shown as below. Steps 1. On the main page of the ZXHN H267N, select Local Network > Status to go to the Local Network Status page. The page is shown in Figure 4-1.
WLAN Basic Settings configuration features. Steps 1. On the main page of the ZXHN H267N, select Local Network > WLAN > WLAN Basic to go to the WLAN Basic page. WLAN Global Configuration 2. Click WLAN Global.
Page 59
Interval Range: 1 – 5. Default: 1. Fragment Threshold Default: 2346. 4. Click Apply button to apply the changes. WLAN SSID Settings 5. Click WLAN Global Prameter. The page is shown in Figure 4-3. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
WLAN Advanced configuration features. Steps 1. On the main page of the ZXHN H267N, select Local Network > WLAN > WLAN Advanced to go to the WLAN Advanced page. Access Control-Mode Settings 2. Click Access Control-Mode Settings. The page is shown in Figure 4-4.
WMM. support BE_AC/BK_AC/VI_AC/VO_AC control types. Steps 1. On the main page of the ZXHN H267N, select Local Network > WLAN > WMM to go to the WMM page, as shown in Figure 4-6. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
4.2.4 Configure the WPS This page provides the parameters of configuration features. Steps 1. On the main page of the ZXHN H267N, select Local Network > WLAN > WPS to go to the WPS page, as shown in Figure 4-7.
The relevant information of Internet status includes Allocated Address, DHCP Server, DHCP Binding and Port Control-DHCP. Steps 1. On the main page of the ZXHN H267N, select Local Network > LAN > IPv4 to go to the IPv4 page. Allocated address 2.
Select On to let the device work as a DHCP server and assign addresses to the client PCs or wireless devices. LAN IP Address address of LAN. Subnet Mask Subnet mask of the device. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
The end address of the DHCP address pool. Gateway It is usually the address of the ZXHN H267N device by default. Assign IspDNS Select On to let the Assign IspDNS work. Primary addresses of the server1, provided by the ISP.
– End of Steps – 4.3.2 Configure the LAN(IPv6) The section describes how to configure Management-IPv6. The relevant information of Internet status includes Allocated Address, DHCP Server, Prefix Management, Port Control-DHCPv6&RA and RA Service. 4-11 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
IPv6 WAN connection. Steps 1. On the main page of the ZXHN H267N, select Local Network > LAN > IPv6 to go to the IPv6 page. Allocated address 2. Click Allocated Address. Allocated address page is displayed, see Figure 4-12.
7. Click Apply button to apply the changes. Port Control-DHCPv6&RA. 8. Click Port Control-DHCPv6&RA. The page is shown in Figure 4-15. Figure 4-15 Port Control-DHCPv6&RA(IPv6) Page 4-13 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide 9. Select the interface or SSID on which you want to disable or enable the DHCP function. Note: Click All On to select all IPv6 DHCP Service-Port Control types. Click All Off to cancel all IPv6 DHCP Service-Port Control types.
Before configuring Route(IPv4), make sure that the IPv4 WAN connection is created. Steps 1. On the main page of the ZXHN H267N, select Local Network > Route > IPv4 to go to the Route(IPv4) page. Routing table 2. Click Routing Table.
Source mask of the network segment. Destination Destination address. Destination Mask Destination mask of the network segment. Protocol The protocol includes the following: ICMP Source Port Source port number. Destination Port Destination port number. Source Source address. 4-17 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Before configuring Route(IPv6), make sure that the IPv6 WAN connection is created. Steps 1. On the main page of the ZXHN H267N, select Local Network > Route > IPv6 to go to the Route(IPv6) page. Routing table. 2. Click Routing Table.
IPv6 address and prefix length, range: 0–128. Gateway The next-hop IP address to the destination network. 6. Click Apply button to apply the changes. Policy routing 7. Click Policy Routing. The page is shown in Figure 4-22. 4-19 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Chapter 4 Configure the Local Network Steps 1. On the main page of the ZXHN H267N, select Local Network > FTP to go to the FTP page. The page is shown in Figure 4-23. Figure 4-23 FTP Page 2. Set the parameters. For a description of the parameters, refer to Table 4-15.
2. Click Apply button to apply the changes. – End of Steps – 4.7 Configure the DMS The section describes how to configure DMS. Prerequisite device is connected to the ZXHN H267N device. 4-22 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Chapter 4 Configure the Local Network Steps 1. On the main page of the ZXHN H267N, select Local Network > DMS to go to the DMS page. The page is shown in Figure 4-25. Figure 4-25 DMS Configuration Page 2. Set the parameters. For a description of the parameters, refer to Table 4-17.
ZXHN H267N Maintenance Management Guide Steps 1. On the main page of the ZXHN H267N, select Local Network > DNS to go to the DNS page. The page is shown in Figure 4-26. Figure 4-26 DNS Configuration Page Domain name 2.
The page is shown in Figure 4-28. Figure 4-28 DNS Page 8. Type the address of the server assigned by the ISP. 9. Click Apply button to apply the changes. – End of Steps – 4-25 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 82
ZXHN H267N Maintenance Management Guide This page intentionally left blank. 4-26 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
2. Click Refresh to refresh the information. – End of Steps – 5.2 Configure the SIP Accounts This procedure describes how to configure basic parameters of the VoIP service, including sip account, authorization username, password. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. Select Application > VoIP > SIP Accounts. The SIP Accounts page is displayed, Figure 5-2. Figure 5-2 SIP Accounts Page 2. Set the parameters. For a description of the parameters, refer to .
Maximum value of the jitter range, default: 200 ms. Echo Cancellation Whether to disable the echo cancellation feature. 3. Click Apply. – End of Steps – 5.4 Configure the SIP Protocol This procedure describes how to configure the SIP Protocol. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. Select VoIP > SIP Protocol. The SIP Protocol page is displayed, see Figure 5-4. Figure 5-4 SIP Protocol Page 2. Set the parameters. For a description of the parameters, refer to 。 Table 5-3 Parameter Descriptions for the SIP Protocol...
Figure 5-5 Media Page 2. Select a codec. 3. Click Apply. – End of Steps – 5.6 Configure the Fax The ZXHN H267N supports the T30 and T38-based fax feature. By default, the T38 protocol is used. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. Select VoIP > Fax. The Fax page is displayed, see Figure 5-6. Figure 5-6 Fax Page 2. Set the parameters. For a description of the parameters, refer to Table 5-4. Table 5-4 Parameter Descriptions for the Fax...
6.1 Check the Device Status The relevant information of device status is shown as below. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Status to go to the Status page. The page is shown in Figure 6-1.
This procedure introduces how to manage the user accounts and rights. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Account Management to go to the Account Management page. The page is shown in Figure 6-2.
Specify the new password. Confirmed Password Confirm the new password. 5. Click Apply button to apply the changes. – End of Steps – 6.3 Configure the Login Timeout This procedure introduces how to configure the login timeout. SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Login Timeout to go to the Login Timeout page. The page is shown in Figure 6-4. Figure 6-4 Login Timeout Configuration Page 2.
Before upgrading software, make sure that the upgrade file is ready. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > System Management > Firmware Upgrade to go to the Firmware Upgrade page. The page is shown in Figure 6-6.
The user can configure the device settings based on his own requirements, and the configuration can be backed up. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > System Management > User Config Management to go to the User Config Management page.
Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Mirror Configuration to go to the Mirror Configuration page. The page is shown in Figure 6-8.
TR-069 configuration features. The relevant TR-069 includes Basic Configuration and Certificate Management. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > TR-069 to go to the TR-069 page. The page is shown in Figure 6-9.
Page 97
Description of the automatic configuration server that manages the device. Username/Password User name and password for the ZXHN H267N device to log in to the automatic configuration server. Connection Request Connection request URL, which is automatically generated by the system.
6.7 Manage the Log This procedure introduces how to manage the log. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Log Management to go to the Log Management page. The page is shown in Figure 6-11.
– End of Steps – 6.8 Diagnosis The section describes how to diagnosis. Diagnosis provides the parameters of the Diagnosis configuration features. The relevant information includes Ping Diagnosis, Trace Route Diagnosis, PPPoE Diagnosis and DSL Line Diagnosis. 6-11 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
ZXHN H267N Maintenance Management Guide Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > Diagnosis to go to the Diagnosis page. The page is shown in Figure 6-12. Figure 6-12 Diagnosis Configuration Page Ping Diagnosis 2.
Maximum Hops, Wait time, and Protocol. 7. After the configuration, click Diagnosis. PPPoE Diagnosis 8. Click PPPoE Diagnosis. The page is shown in Figure 6-15. Figure 6-15 PPPoE Diagnosis Page 9. Select one PPPoE connection. 6-13 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
6.9 Check the ARP Table The relevant information of table is shown as below. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > ARP Table to go to the ARP Table page, as shown in Figure 6-17.
6.10 Check the MAC Table The relevant information of table is shown as below. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > MAC Table to go to the MAC Table page, as shown in Figure 6-18.
This page will help you convert LAN to WAN interface. Steps 1. On the main page of the ZXHN H267N, select Management & Diagnosis > ETH Uplink Management to go to the ETH Uplink Management page, as shown in Figure 6-19.
Table 4-4 Access Control-Rule parameters ............... 4-6 Table 4-5 Parameter Descriptions for the WMM ............4-7 Table 4-6 Parameter Descriptions for the WPS ............4-8 Table 4-7 Parameter Descriptions for the DHCP Server ........... 4-9 SJ-20140702105807-002|2014-11-13 (R1.0) ZTE Proprietary and Confidential...
Page 112
ZXHN H267N Maintenance Management Guide Table 4-8 Parameter Descriptions for the DHCP Binding......... 4-11 Table 4-9 Parameter Descriptions for the DHCP Server ......... 4-13 Table 4-10 Parameter Descriptions for the RA Service ........... 4-14 Table 4-11 Parameter Descriptions for the Static Routing........4-16 Table 4-12 Parameter Descriptions for the Policy Routing(IPv4)......