Changing Channels-Analog-Tv; Changing Channels-Digital-Tv - Sharp Aquos LC 45GD4U Operation Manual

Watching TV
Please note: your new AQUOS Liquid Crystal Television is capable of receiving the full range of cable-TV channels available
today, from the most advanced digital and HDTV channels, to the more traditional analog channels. As the transition toward
full digital TV continues, some cable-TV systems in the USA will have a mixture of analog and digital channels in their
lineups. When you are viewing analog cable-TV channels and wish to switch to viewing digital cable-TV channels, you must
press the DIGITAL button (located just below the numbers) on the remote control first. In similar fashion, when you are
viewing digital channels and wish to switch to viewing analog channels, you must press either the ANALOG-A or ANALOG-
B button (depending on whether you have your cable connected to the A or B terminal) on the remote first.
Changing channels - Analog-TV
You can change channels in several ways.
NOTE
• While watching a broadcast, press A-ANALOG-B to view
the image received from the other tuner.
Method 1
Using CHr/s on the remote control unit or on the
display.
Method 2
1. Press FLASHBACK to switch to the previously tuned
channel.
2. Press FLASHBACK again to switch back to the
currently tuned channel.
NOTE
• FLASHBACK will not work if no channel has been
changed after TV is turned on.
Method 3
Using remote control buttons (0-9
up to 125 channels for VHF/UHF/CATV.
To select a 1 or 2-digit channel number
(e. g., Channel 5):
Press 5 s ENTER
ANALOG-A Air
5
NOTE
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.
• • (DOT) can be used instead of ENTER.
To select a 3-digit channel number
(e. g., Channel 115):
s s
Press 1 1 5
ANALOG-B Cable
1
NOTE
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.
• If you push "0" by itself, nothing will happen.
22
and ENTER) to select
ANALOG-A Air
5
ANALOG-B Cable ANALOG-B Cable
11 115
Changing channels - Digital-TV
You can change channels in several ways.
As well as the methods outlined below, you can also select
programs using the Channel List. (See page 86.)
NOTE
• While watching a broadcast, press DIGITAL.
■ Digital - Air (Two-part Number)
Method 1
When you press CHr/sor FLASHBACK, repeat the
same steps for Analog-TV.
Method 2
Using remote control buttons (0-9,
ENTER) to select the channels including a decimal
point.
To select a 4-digit channel number
(e. g., Channel 22.1):
Press 2 s 2 s•(DOT) s1s
DIGITAL Air DIGITAL Air DIGITAL
2 22
NOTE
• Complete the above steps within a few seconds.
• When you enter 0-9 and •(DOT), channel selection will
be made if there is no operation for a few seconds.
■ Digital - Cable (One-part Number)
Method 1
When you press CHr/sor FLASHBACK, repeat the
same steps for Analog-TV.
Method 2
Using remote control buttons (0-9
the channels including a decimal point.
To select a 3-digit channel number
(e. g., Channel 310):
Press 3 s1s0s ENTER
DIGITAL Cable DIGITAL Cable
3 31
NOTE
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.
• (DOT) and
ENTER
Air DIGITAL Air DIGITAL Air
22. 22.1 22.1
and ENTER) to select
DIGITAL Cable DIGITAL Cable
310 310