Kenwood ProTalk NX-240V16P Operating Manual page 4

Enables or disables the Scrambler/Encryption.
(09) Scrambler/Encryption
Toggles the Squelch Off between enabled and disabled.
(10) Squelch Off
While this key is pressed and held, the squelch is open and the
transceiver unmutes the speaker.
This function cannot be assigned as a Hold function.
(11) Squelch Off Momentary
If "Squelch Off Momentary" is selected from the Press dropdown list,
"None" will automatically be configured in the Hold dropdown list,
and this configuration cannot be changed.
Pressing and holding this key for 4 sec activates the Super Lock
function. Super Lock is the function to prevent accidental operation
of the transceiver. Even if the transceiver is turned OFF and ON
again, the Super Lock status will be retained. To deactivate Super
Lock, turn OFF the transceiver, and press and hold the Side 2 key
while turning ON the transceiver. Once an LED lights orange,
release the Side 2 key within 2 sec.
This function cannot be assigned as a Press function.
If "Super Lock" is selected from the Hold dropdown list, None will
automatically be configured in the Press dropdown list, and 4.0 s will
(12) Super Lock
automatically be configured in the Hold Delay exit box, and these
configurations cannot be changed.
Following keys can still be used while Super Lock mode is On.
PTT switch
•
Squelch Off
•
Squelch Off Momentary
•
Monitor
•
Monitor Momentary
•
Toggles the Transmit Power of the transceiver between High and
(13) Low Transmit Power
Low.
Switches the RX/TX Frequency Scan On or Off for a channel with
(14) RX/TX Frequency Scan
Repeater Mode enabled and RX/TX Frequency Scan enabled.
Decreases the Zone number in steps of 1.
(15) Zone Down
Increases the Zone number in steps of 1.
(16) Zone Up
To change the functions of the Side 1 and Side 2 keys:
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
[1] With the transceiver power OFF, press and hold the Side 1 and Side 2 keys
while turning the transceiver power ON.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• Continue to hold the Side 1 and Side 2 keys until the LED lights orange
and the transceiver announces "Setup".
[2] Release the keys, and the transceiver will announce "Table Zero".
○ ○ ○ ○ -- ○ ○ ○ ○ --
[3] Press the Side 1 or Side 2 to increment / decrement the table number and
press the PTT Switch to select the function that you want to assign to a key
(either the Side 1 or the Side 2, a press or a hold).
[4]
Press the Side 1 key to assign the function selected in the above [3]
•
to the Side 1 key press.
Hold the Side 1 key to assign the function to the Side 1 key hold.
•
Press the Side 2 key to assign the function to the Side 2 key press.
-- ○ ○ ○ ○ -- ○ ○ ○ ○
•
Hold the Side 2 key to assign the function to the Side 2 key hold.
•
[5] Beeps will sound at the completion of [4] key assignment.
You will need to repeat [3] and [4] to assign more functions to press/hold key.
[6] Turn the transceiver power OFF and then ON again to activate the new settings.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Note: The transceiver will automatically return to normal operation if no action is performed for 20 seconds.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
ALL RESET MODE
At some point in time, you may desire to reset the transceiver settings to their default values. This function
will reset all channels to their default analog frequencies and QT/DQT, the VOX function to its default status,
and all keys to their default functions.
To reset the transceiver:
[1] With the transceiver power OFF, press and hold the PTT switch, the Side 1 key, and the Side 2 key
while turning the transceiver power ON.
• Continue to hold the keys for 2 seconds, until the LED lights orange.
[2] Release the keys.
• The keys must be released within 1 second after the LED lights orange,
otherwise All Reset Mode will cancel.
• The transceiver announces "Confirm" and returns to normal operation
in the default settings.
"Setup"
"Table Zero"
"Table #"
Select
"Side 1 or 2"
"Press or Hold"
"Confirm"