MULTIQUIP WHITEMAN SERIES Operation And Parts Manual
  1. Manuals
  2. Brands
  3. MULTIQUIP Manuals
  4. Utility Vehicle
  5. Whiteman series
  6. Operation and parts manual
MULTIQUIP WHITEMAN SERIES Operation And Parts Manual

MULTIQUIP WHITEMAN SERIES Operation And Parts Manual

Power buggy (gx390 electric start gasoline engine)
Hide thumbs Also See for WHITEMAN SERIES:
Table of Contents

Advertisement

Quick Links

OPERATION AND PARTS MANUAL
SERIES
MODEL
WBH-16EF CE
POWER BUGGY
(GX390 ELECTRIC START GASOLINE ENGINE)
Revision #0 (09/19/18)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Advertisement

Table of Contents
loading

Related Manuals for MULTIQUIP WHITEMAN SERIES

Summary of Contents for MULTIQUIP WHITEMAN SERIES

  • Page 1 OPERATION AND PARTS MANUAL SERIES MODEL WBH-16EF CE POWER BUGGY (GX390 ELECTRIC START GASOLINE ENGINE) Revision #0 (09/19/18) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

  • Page 2: Proposition 65 Warning

    PROPOSITION 65 WARNING Engine exhaust some its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS WBH-16 CE POWER BUGGY Component Drawings Proposition 65 Warning ........... 2 Nameplate And Decals Assembly ....46-47 Table Of Contents ............ 3 Hydraulic Drive Assembly ......... 48-49 Parts Ordering Procedures ........4 Hydraulic Pump Assembly ........ 50-51 Safety Information ..........

  • Page 4: Parts Ordering Procedures

    , 2006 Order via Internet (Dealers Only) Best Deal! If you have an MQ Account, to obtain a Username Order parts on-line using Multiquip’s SmartEquip website! and Password, E-mail us at: parts@multiquip. com. ■ View Parts Diagrams ■ Order Parts To obtain an MQ Account, contact your District Sales Manager for more information.

  • Page 5: Safety Information

    SAFETY INFORMATION Do not operate or service the equipment before reading Potential hazards associated with the operation of this the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which at all times when operating this equipment. may appear throughout this manual in conjunction with Failure to read and understand the safety safety messages.
  • Page 6 „ NEVER use accessories or attachments that are not „ Avoid wearing jewelry or loose fi tting clothes that may recommended by Multiquip for this equipment. Damage snag on the controls or moving parts as this can cause to the equipment and/or injury to user may result.
  • Page 7 SAFETY INFORMATION DANGER CAUTION „ Engine fuel exhaust gases contain poisonous carbon „ ALWAYS inspect the surface over which you will travel. monoxide. This gas is colorless and odorless, and can Look for holes, drop-offs and obstacles. Look for rough cause death if inhaled.
  • Page 8 SAFETY INFORMATION „ DO NOT operate the power buggy at excessive speeds. „ DO NOT stand in front or along side the buggy when „ DO NOT operate the power buggy at excessive speeds. Reckless operation may cause accidents and severe injury.
  • Page 9 SAFETY INFORMATION „ ALWAYS use extreme caution when working with ENGINE SAFETY fl ammable liquids. WARNING „ DO NOT fi ll the fuel tank while the engine is running „ DO NOT place hands or fingers inside or hot. engine compartment when engine is „...
  • Page 10 SAFETY INFORMATION TRANSPORTING SAFETY „ ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous concentration NOTICE of combustible gases. „ ALWAYS shutdown engine before transporting. „ If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, „...
  • Page 11 SAFETY INFORMATION ENVIRONMENTAL SAFETY/DECOMMISSIONING EMISSIONS INFORMATION NOTICE NOTICE Decommissioning is a controlled process used to safely This equipment conforms with applicable Environmental retire a piece of equipment that is no longer serviceable. Protection Agency (EPA) and California Air Resources If the equipment poses an unacceptable and unrepairable Board (CARB) emission regulations.

  • Page 12: Specifications (Buggy)

    SPECIFICATIONS (BUGGY) Table 1. Specifications (Power Buggy) Models WBH-16EF CE Maximum Weight Capacity 2,500 lbs. (1,134 kg) (Dual Wheels) Maximum Weight Capacity 1,100 lbs. (500 kg) (Single Wheels) Operating Weight 1,415 lbs. (641.8 kg.) Bucket/Tub Capacity 16 cu. ft. Water Level (.59 cu. yd.) Bucket/Tub Material Polyethylene Drive...

  • Page 13: Noise And Vibration/Engine Specifications

    NOISE AND VIBRATION/ENGINE SPECIFICATIONS Table 2. Noise and Vibration Emissions Model WBH-16 CE Guaranteed ISO 11201:2010 Based 82.74 Sound Pressure Level at Operator Station in dB(A) Guaranteed ISO 3744:2010 Based Sound Power Level in dB(A) Sound Pressure Level Horn in dB(A) SA(8) Hand Arm Vibration Per ISO 2631-1:1997+A1:2010 in m/s 1.28 m/s...

  • Page 14: Dimensions

    DIMENSIONS SIDE VIEW WBH-16 REAR VIEW Table 4. Dimensions Reference Dimension Letter in. (mm) 45.47 (1,155) 51.0 (1,295) 8.50 (216) 103 (2,612) 30.75 (781) 42.75 (1,085) Figure 1. WBH16EF CE Dimensions PAGE 14 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)

  • Page 15: General Information

    GENERAL INFORMATION The MQ Whiteman Power Buggy, WBH-16EF CE (electric The operator controls the forward and reverse machine start) is intended for the transportation of concrete, concrete travel by manually shifting the control valve which directs spreading and spot pouring. In addition, this power buggy the hydraulic fluid flow to the two drive wheel motors.

  • Page 16: Components

    COMPONENTS Figure 2. WBH-16EF Power Buggy Components 1. Tub or Bucket — Used for the transportation of 8. Speed Control — Sets the power buggy's travel speed. material. Tub holds approximately 16 cubic feet When fully depressed, the buggy will be at FULL speed. (0.59 cubic yards) of water.
  • Page 17 COMPONENTS CON'T Figure 3. WBH-16EF Power Buggy Components Continued 15. Dump Control Lever — Use this lever forward to place 21. Fuse — 10 amp fuse that provides protection for the the tub in the dump position (vertical), move the lever horn circuit.

  • Page 18: Engine Components

    ENGINE COMPONENTS Figure 4. Honda GX390 Engine INITIAL SERVICING The engine (Figure 4) must be checked for proper 7. Choke Lever – Used in the starting of a cold engine, lubrication and filled with fuel prior to operation. Refer to the or in cold weather conditions.

  • Page 19: Inspection

    INSPECTION BEFORE STARTING 1. Read all safety instructions at the beginning of manual. UPPER LIMIT 2. Clean the unit, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.
  • Page 20 INSPECTION BATTERY When connecting battery do the following: 1. NEVER connect the battery cables to the battery This unit is of negative ground DO NOT connect in reverse. terminals when the ignition is in the ON position (start). ALWAYS maintain battery fluid level between the specified marks.
  • Page 21 INSPECTION DUMP CYLINDER CHECK 1. Check the power buggy's dump cylinder as outlined in the operation section of this manual. 2. Make sure that both zerk fittings for the dump cylinder have been lubricated. HYDRAULIC OIL CHECK 3. Visually read the hydraulic sight glass (Figure 9) to see if the hydraulic oil level is low.

  • Page 22: Operation

    OPERATION CAUTION DO NOT attempt to operate the power buggy until the Safety Information, General Information, and Inspection sections of this manual have been read and thoroughly FUEL VALVE LEVER understood. ELECTRIC START 1. Before attempting to start the power buggy, make sure that the safety kill switch (Figure 10) is not pushed Figure 12.
  • Page 23 OPERATION 6. If starting a warm engine or the temperature is warm, 8. Place the ignition key (Figure 17 ) in the START position place the choke lever (Figure 15) in the OPEN position. and hold it until the engine starts. When the engine starts, release the key, allowing it to return back to the ON position.
  • Page 24 OPERATION PRE-CHECK PARKING BRAKE/DIRECTION LEVER 1. Engage the parking brake lever (Figure 18) and attempt Before the power buggy can be put into operational use, to rock the buggy back and forth. If the wheels turn it is best to perform a test run to make certain that all during the rocking motion, adjust the brakes as outlined components are functioning properly.
  • Page 25 OPERATION TRAVELING STEERING 1. With the engine running and parking brake released, To steer the buggy, use the handle bar in front of the place the direction lever (Figure 20) in the forward operator platform. direction. 1. To turn left when traveling in the forward direction, turn 2.
  • Page 26 OPERATION When traveling on a slope, it is necessary to determine To determine the % grade of your path of travel, use the the grade of the path. The WBH-16 can travel up or down formula and graphs as shown in Figure 23. a maximum grade of 10% (6°).
  • Page 27 OPERATION TUB (BUCKET) DUMPING The hydraulic dump can be controlled by the hand dump control lever or foot dump pedal. NOTICE 1. To place the tub in the vertical position press down on DO NOT activate dump mechanism (tub/bucket) if the dump pedal (Figure 25A) or move the dump control buggy is facing down hill.
  • Page 28 OPERATION SHUTDOWN (NORMAL) 5. Cycle hydraulic controls to eleminate residual pressure. 6. Remove ignition key. Correct shutdown is important to safe operation. Follow these general steps: 7. Block wheels if on a slope or incline. 1. Come to a full stop. EMERGENCY SHUTDOWN 2.

  • Page 29: Maintenance

    MAINTENANCE Table 6. Engine Maintenance Schedule EVERY 6 EVERY BEFORE FIRST EVERY 2 DESCRIPTION MONTHS YEAR OPERATION EACH MONTH OR YEARS OR OR 100 OR 300 25 HRS. 500 HRS. HRS. HRS. Check Engine Oil Change Engine Oil Filter Replace Every 100 Hrs.
  • Page 30 MAINTENANCE ENGINE AIR CLEANER When performing any maintenance on the power buggy or engine, follow all safety messages and rules for safe NOTICE operation stated at the beginning of this manual. Operating the engine with loose or damaged air cleaner WARNING components could allow unfiltered air into the engine causing premature wear and failure.
  • Page 31 MAINTENANCE 4. Clean foam element in warm, soapy water or IN-LINE FUEL FILTER (200 HOURS) nonflammable solvent. Rinse and dry thoroughly. Dip the element in clean engine oil and completely squeeze 1. Place the fuel tank ON/OFF valve lever (Figure 33) in the out the excess oil from the element before installing.
  • Page 32 MAINTENANCE SPARK ARRESTER CLEANING SPARK PLUG ADJUSTMENT Clean the spark arrester every 6 months or 100 hours. 1. Make sure the engine is cool before servicing the spark plugs. 1. Remove the 4 mm screw (3) from the exhaust deflector (Figure 36), then remove the deflector.
  • Page 33 MAINTENANCE ADDING HYDRAULIC OIL 5. Use the tub support rod to support the tub, then turn the engine OFF. 1. Check the hydraulic oil level in the hydraulic oil tank, 6. Remove the two bolts that secure the access by reading the hydraulic oil sight glass (Figure 39) cover(Figure 41) to the buggy frame.
  • Page 34 9. Replace hydraulic oil after every 200 hours of operation. NOTICE The reservoir capacity is 5.3 gallons (20.4 liters). The Contact Multiquip's Service Department should any hydraulic oil filter should be changed each time the problems develop with the hydraulic drive motors hydraulic oil is changed.
  • Page 35 MAINTENANCE CHASSIS LUBRICATION PUMP CONTROL LEVER ADJUSTMENT This power buggy is equipped with five zerk fittings Inspect the speed control return springs. The tension should (Figure 46). Lubricate these zerk fittings each day before be sufficient to allow lever to snap back when released. operating the buggy.
  • Page 36 MAINTENANCE TIRES/WHEELS/LUG NUTS Table 8. Tire Torque Requirements First Pass Second Pass Third Pass Tires and wheels are very important and critical components Wheel Size FT-LBS FT-LBS FT-LBS of the buggy. When specifying or replacing the wheels, it is important that the wheels, tires, and axle are properly 480 x 8 in.

  • Page 37: Troubleshooting

    TROUBLESHOOTING Troubleshooting (Power Buggy) Symptom Possible Problem Solution Adjust speed control cable. Replace cable if Speed control cable out of adjustment? necessary Hydraulic oil level low.? Check hydraulic oil level. Add oil if necessary. Loss of Power. Contaminated hydraulic oil fi lter? Replace hydraulic oil fi lter.
  • Page 38 TROUBLESHOOTING Troubleshooting (Engine) Symptom Possible Problem Solution Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Short circuit due to defi cient spark plug Check spark plug insulation, replace if worn. insulation? Improper spark plug gap? Set to proper gap.
  • Page 39 TROUBLESHOOTING Troubleshooting (Engine) - continued Symptom Possible Problem Solution Air cleaner dirty? Clean or replace air cleaner. Improper level in carburetor? Check fl oat adjustment, rebuild carburetor. Weak in power, compression is proper and does not misfi re. Defective spark plug? Clean or replace spark plug.

  • Page 40: Hydraulic System Diagram

    HYDRAULIC SYSTEM DIAGRAM HYDRAULIC OIL TANK HYD. OIL FILTER 200 MICRON DUMP CYLINDER SCREEN/MESH CHARGE PUMP RELIEF VALVE 1000 PS1 ± 50 EATON PUMP 17 GPM SPIN-ON RETURN FILTER 10 MICRON DIRECTION VALVE DUMP VALVE DRIVE MOTOR DRIVE MOTOR NORMALLY UP TO NORMALLY UP TO 17 GPM 17 GPM...

  • Page 41: Hydraulic Hose Connections

    HYDRAULIC HOSE CONNECTIONS HYDRAULIC PUMP DUMP CYLINDER HYDRAULIC OIL TANK FRAME HYDRAULIC OIL FILTER DUMP VALVE DRIVE MOTORS WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18) — PAGE 41...

  • Page 42: Wiring Diagram

    WIRING DIAGRAM IGNITION SWITCH POSITION CIRCUIT MAKE BLK 16 AWG BLK 16 AWG G+M+A B+L+A START B+L+S SPARK PLUG IGNITION SWITCH OIL LEVEL SWITCH BLK 16 AWG SWITCH UNIT OIL LEVEL ENGINE POSITION NORMAL OPEN LOW LEVEL CLOSED IGNITION CHASSIS GND.
  • Page 43 NOTES WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18) — PAGE 43...

  • Page 44: Explanation Of Code In Remarks Column

    A blank entry generally indicates that the item is not sold “Not Sold Separately” — Indicates that an item cannot separately or is not sold by Multiquip. Other entries will be purchased as a separate item and is either part of an be clarifi ed in the “Remarks”...

  • Page 45: Suggested Spare Parts

    SUGGESTED SPARE PARTS WBH16 POWER BUGGY ENGINE HONDA GX390RT2QNB2 (ELECTRIC START) 1 to 3 units 1 to 3 units Qty. Description 1....508667 ....FILTER, HYDRAULIC OIL Qty. Description 1....EM16477 ....CAP, HYDRAULIC OIL TANK 3....9807955846 ..SPARK PLUG 1....18035 ....PUMP, HYDRAULIC 3....11078 ....KEY, IGNITION 1....18051 ....COUPLING, ENGINE SHAFT 3....17210ZE3505 ..AIR FILTER, ELEM.
  • Page 46 NAMEPLATE AND DECALS ASSY. WARNING CRUSH AREA 18247 TRAVEL NEUTRAL MODEL SERIAIAL NO. LIFT 513608 WBH-16 WARNING To avoid injury you MUST read and understand operator’s manual before using this machine. This machine to be operated by qualied personnel only. LIFT Ask for training 18245...
  • Page 47 NAMEPLATE AND DECALS ASSY. PART NO. PART NAME QTY. REMARKS 18247 DECAL, CRUSH WARNING DECAL, TRAVEL LEVER DIRECTION .....1..MOLDED INTO FUEL TANK COVER PLATE, SERIAL NUMBER........1..CONTACT MQ PARTS DEPT. 491757 RIVET, I.D. PLATE 18248 DECAL, HOT SURFACE WARNING 18251 DECAL, WBH-16 18252 DECAL, MQ WHITEMAN 18245...
  • Page 48 HYDRAULIC DRIVE ASSY. VIEW FROM OPERATOR’S PLATFORM DIRECTIONAL VALVE SEAL KIT DRIVE MOTOR LEFT DRIVE MOTOR RIGHT DRIVE MOTOR NOTES: FOAM FILLED REFERENCE HYDRAULIC HOSE CONNECTION SECTION. REFERENCE PUMP ASSEMBLY. PAGE 48 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 49 HYDRAULIC DRIVE ASSY. PART NO. PART NAME QTY. REMARKS 18265M HOSE, DIRECTION VALVE .........1....RIGHT-DRIVE MOTOR 18264M HOSE, DIRECTION VALVE .........1....LEFT-DRIVE MOTOR 511810 ADAPTER, ELBOW 18276M HOSE, LH HYDRAULIC MOTOR 512189 ADAPTER, TEE CONNECTOR 492527 NUT, HEX 1/2"-20 18029F WHEEL, DRIVE ASSY. FRONT ......4....FOAM FILLED TIRE 511692 FLANGE, HUB 18237...

  • Page 50: Hydraulic Pump Assembly

    HYDRAULIC PUMP ASSY. HYDRAULIC PUMP DIRECTION VALVE SEAL KIT DIRECTIONAL VALVE HYDRAULIC OIL FILTER DUMP VALVE NOTES: REFERENCE HYDRAULIC HOSE CONNECTION SECTION. REFERENCE HYDRAULIC OIL TANK ASSEMBLY. REFERENCE DUMP VALVE ASSEMBLY. REFERENCE HYDRAULIC DRIVE ASSEMBLY ITEMS 1 AND 2 FOR HOSE PART NUMBERS PAGE 50 —...
  • Page 51 HYDRAULIC PUMP ASSY. PART NO. PART NAME QTY. REMARKS 18035 PUMP, HYDRAULIC 511808 ADAPTER, STRAIGHT 3365 ADAPTER, STRAIGHT 18256M HOSE, PUMP TO DUMP VALVE 18258M HOSE, FILTER TO PUMP 18261M HOSE, PUMP TO TANK 18265M HOSE, PUMP TO DIRECTION VALVE ....1....REPLACES P/N 18263M 512190 ADAPTER, STRAIGHT 18257M...
  • Page 52 HYDRAULIC DUMP ASSY. DUMP CYLINDER SEAL KIT DUMP CYLINDER DUMP VALVE NOTES: REFERENCE HYDRAULIC HOSE CONNECTION SECTION. REFERENCE HYDRAULIC PUMP ASSEMBLY ITEM 4 FOR HOSE PART NUMBER. REFERENCE HYDRAULIC PUMP ASSEMBLY ITEM 9 FOR HOSE PART NUMBER. REFERENCE HANDLE/FOOT DUMP CONTROLS ASSEMBLY ITEM 8 FOR DUMP VALVE PART NUMBER.
  • Page 53 HYDRAULIC DUMP ASSY. PART NO. PART NAME QTY. REMARKS 18022 CYLINDER, HYDRAULIC DUMP 18022SK SEAL KIT, DUMP CYLINDER 491705 ZERK FITTING 511803 ADAPTER, ELBOW 18020 HOSE, DUMP VALVE TO HYD. PISTON 511804 ADAPTER, ELBOW MALE 512234 ADAPTER, ELBOW 511806 ADAPTER, STRAIGHT 506191 ADAPTER, ELBOW WBH-16EF CE POWER BUGGY •...
  • Page 54 PUMP AND COUPLING ASSY. Engine BLUE LOCTITE HYDRAULIC PUMP NOTES: ITEMS 2A THROUGH 2D NOT INCLUDED WITH ITEM 2. FRAME 2 APPLY BLUE LOCTITE PAGE 54 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 55 PUMP AND COUPLING ASSY. PART NO. PART NAME QTY. REMARKS 492472 SCREW, ALLEN HEAD 3/8"-16 X 3/4" 18051 COUPLING, ENGINE SHAFT ......1....INCLUDES ITEMS W/# 18051RS SPIDER, URETHANE 492356 SCREW, 1/4" X 3/4" GRD 5 492622 WASHER, LOCK 1/4" EM923057 WASHER, FLAT 3/4" ..........1....REPLACES P/N 504451 18112 492596 WASHER, FLAT 1/4"...
  • Page 56 TUB ASSY. PAGE 56 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 57 TUB ASSY. PART NO. PART NAME QTY. REMARKS 18004 TUB, PLASTIC, 16 CU. FT. 492313 SCREW, HHC 3/8"-16 X 1-1/2" 512193 WASHER, FLAT 3/8" LARGE 490957 RING, SNAP 18130 PIN, HYD. PISTON CROSS 18129 PIN, TUB FRAME CROSS 0202 SCREW, HHC 5/16"-18 X 1 ZINC ......4....REPLACES P/N 492364 492597 WASHER, FLAT 9.5 X 22.2 492583...
  • Page 58 PANEL ASSY. PAGE 58 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 59 PANEL ASSY. PART NO. PART NAME QTY. REMARKS 503978 POP RIVET AM-56 511474 FASTENER, ACCESS DOOR 18008 DOOR, ACCESS 492355 SCREW, 1/4" X 1/2" NC GRD 5 492597 WASHER, FLAT 3/8" 18141 COVER, RIGHT/SIDE ENGINE 492364 SCREW, HHC 5/16"-18 X 1 492582 NUT, NYLOC 5/16"-18 801026...
  • Page 60 BRAKE ASSY. PAGE 60 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 61 BRAKE ASSY. PART NO. PART NAME QTY. REMARKS 511762 SCREW, HHC 1/2"-13 X 8 511698 CLEVIS, ASSY. BRAKE 492574 NUT, HEX 3/8"-24 NF 18111 PEDAL, BRAKE WASHER, FLAT 1/2" 492584 NUT, NYLOC 1/2"-13 18167 SPRING, BRAKE PEDAL 18307 SPRING, BRAKE BAND, BRAKE ...........2....NOT SOLD SEPARATELY LINING, BRAKE ..........2....NOT SOLD SEPARATELY 503723...

  • Page 62: Hydraulic Oil Tank Assembly

    STEERING AND CONTROLS ASSY. 10 AMP FUSE HYDRAULIC OIL TANK HYDROSTATIC PART OF MOTOR BASE NOTES: BEARING, ITEM 27 AND BUSHING ITEM 31 ARE LOCATED INSIDE STEERING AXLE. FOAM FILLED PAGE 62 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 63 STEERING AND CONTROLS ASSY. PART NO. PART NAME QTY. REMARKS 2508 SCREW, HHC 1/4"-20 X 2-1/4" ......1....REPLACES P/N 512414 492369 SCREW, HHC 5/16"-18 X 2-1/4" 18183 ROD-END, THROTTLE CABLE 492582 NUT, NYLOC 5/16"-18 504505 WRAP, TIE 4.6 X 360 MM 491030 WRAP, TIE 2.5 X 142 MM 505304...
  • Page 64 CHASSIS ASSY. PAGE 64 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 65 CHASSIS ASSY. PART NO. PART NAME QTY. REMARKS 492583 NUT, NYLOC 3/8" 492598 WASHER, FLAT 3/8" 492313 SCREW, HHC 3/8"-16 X 1-1/2" 503112 SCREW, HHC 3/8"-16 X 2-3/4" EM963610 CAP SCREW 3/8" X 1-1/4" NC GRD 8 ....2....REPLACES P/N 492375 492356 SCREW, HHC 1/4"...
  • Page 66 HANDLE/FOOT DUMP CONTROLS ASSY. SEAL KIT DUMP VALVE REFERENCE HYDRAULIC DUMP ASSY. PAGE 66 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 67 HANDLE/FOOT DUMP CONTROLS ASSY. PART NO. PART NAME QTY. REMARKS 492401 SCREW, HHC 1/2"-13 X 4 503119 NUT, NYLOC 3/16" 18121 KNOB, LEVER 18065 LEVER, DUMP VALVE 512185 SCREW, HHC 1/4"-20 X 1-3/4" 492622 WASHER, FLAT 1/4" 512183 SCREW, HHC 3/16"-24 X 1-1/4" 18064 VALVE, DUMP ...........1....INCLUDES ITEMS W/$ 18064SK...
  • Page 68 HYDRAULIC OIL TANK ASSY. PAGE 68 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 69 HYDRAULIC OIL TANK ASSY. PART NO. PART NAME QTY. REMARKS 520461 RETAINER 801791 O-RING 520460 COVER 520343 O-RING 510717 BOLT, 1/2" X 1-3/4" NC EM16477 CAP, HYDRAULIC OIL TANK 18125 TANK, HYDRAULIC OIL 492376 SCREW, HHC 3/8" X 1-1/4" 492598 WASHER, FLAT 3/8"...
  • Page 70 BATTERY ASSY. PAGE 70 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 71 BATTERY ASSY. PART NO. PART NAME QTY. REMARKS 505500 WING NUT 512557 BATTERY CABLE, NEGATIVE 511250 BATTERY CABLE, POSITIVE 512555 BATTERY SUPPORT BRACKET EM92305 WASHER, FLAT 1/4" ..........6....REPLACES P/N 492596 2101402 WASHER, LOCK 1/4" ........2....REPLACES P/N 492622 508480 BATTERY SUPPORT PLATFORM 492357 BOLT, 3/16"...
  • Page 72 FUEL TANK ASSY. (STEEL) NOTICE Beginning year 2012 with evaporative system. TO ENGINE CARBURETOR AIR FILTER INLET PORT 3/16” 3/16” 5.5 IN. 140 MM O FF 3/16” HOSE REDUCER 1/4” 1/4” 1/4” 3.1 FT. 945 MM TANK PORT PURGE PORT REF.
  • Page 73 FUEL TANK ASSY. (STEEL) PART NO. PART NAME QTY. REMARKS 520820 CAP, FUEL (EPA) 2" DIA. 802006 FUEL TANK NECK SEAL 800845 COVER, FUEL TANK, FRONT, PLASTIC 521392 COVER, FUEL TANK, REAR, PLASTIC 492356 SCREW, 1/4" X 3/4" GRD 5 492622 WASHER, LOCK 1/4"...
  • Page 74 ENGINE MOUNTING ASSY. PAGE 74 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 75 ENGINE MOUNTING ASSY. PART NO. PART NAME QTY. REMARKS 2105164 NUT, NYLOC 5/16" ..........4....REPLACES P/N 492582 505679 WASHER, FLAT 3/8" 513593 90° FITTING 513594 ADAPTER PLUG 492368 SCREW, 5/16" NC X 2" GRD 5 ......1....GROUND CONNECTION 492367 SCREW, 5/16" NC X 1-3/4" GRD 5 WBH-16EF CE POWER BUGGY •...
  • Page 76 ENGINE ASSY. REGULATOR PAGE 76 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 77 ENGINE ASSY. PART NO. PART NAME QTY. REMARKS 520766 ENGINE, HONDA 11 HP ELECTRIC START 503118 BOLT, 3/16" X 1" NC GRD 2 512512 SPACER 18007 MOTOR COVER 492583 NUT, 3/8" NC 492598 WASHER 3/8" EM963057 CAP SCREW 3/8" X 1-1/2" ........2....REPLACES P/N 492313 492581 NUT, 1/4"...

  • Page 78: Engine Service Parts

    ENGINE SERVICE PARTS PAGE 78 — WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18)
  • Page 79 ENGINE SERVICE PARTS PART NO. PART NAME QTY. REMARKS 9807955846 SPARK PLUG 17218ZE3505 AIR FILTER, OUTER 17210ZE3505 AIR FILTER, ELEM. (DUAL).......1....INCLUDES ITEMS W/# WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18) — PAGE 79...

  • Page 80: Terms And Conditions Of Sale - Parts

    Multiquip be $5.00. meeting this requirement. liable for loss of profi t or good will or for any Special order items.
  • Page 81 NOTES WBH-16EF CE POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #0 (09/19/18) — PAGE 81...
  • Page 82 © COPYRIGHT 2018, MULTIQUIP INC. Multiquip Inc , the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual is also suitable for:

Wbh-16ef ce

Table of Contents