ResMed AirFit F30 User Manual
  1. Manuals
  2. Brands
  3. ResMed Manuals
  4. Medical Equipment
  5. AirFit F30
  6. User manual

ResMed AirFit F30 User Manual

Hide thumbs Also See for AirFit F30:

Advertisement

Table of Contents

English
USER GUIDE

Advertisement

Table of Contents
loading

Related Manuals for ResMed AirFit F30

Summary of Contents for ResMed AirFit F30

  • Page 1 English USER GUIDE...

  • Page 2: Intended Use

    Anti-Asphyxia Valve Intended use The AirFit F30 mask is intended to be used by patients weighing more than 66 lb (30 kg) who have been prescribed non-invasive positive airway pressure (PAP) therapy such as CPAP or bi-level therapy. The mask is intended for single patient re-use in the home and multi-patient re-use in the hospital/institutional environment.

  • Page 3: Before Using Your Mask

    Contraindications Use of masks with magnetic components is contraindicated in patients with the following pre-existing conditions: • a metallic hemostatic clip implanted in your head to repair an aneurysm • metallic splinters in one or both eyes. Before using your mask Remove all packaging and inspect each mask component for visible deterioration.

  • Page 4: Removing Your Mask

    1. Twist and pull both magnetic clips away from the frame. 2. Place the cushion under your nose and ensure it sits comfortably against your face. With the ResMed logo on the headgear facing up, pull the headgear over your head.

  • Page 5: Disassembling Your Mask For Cleaning

    Disassembling your mask for cleaning If your mask is connected to a device, disconnect the device air tubing from the mask elbow. 1. Undo the fastening tabs on the upper headgear straps and pull them from the frame. Keep the magnetic clips attached to the lower headgear straps.

  • Page 6: Reassembling Your Mask

    Reassembling your mask 1. With the ResMed logo facing outwards and up, insert the upper headgear straps into the frame from the inside and fold the fastening tabs over to secure. 2. Hold the top and bottom of the cushion and attach to the frame.

  • Page 7: Technical Specifications

    (cracking, crazing, tears etc.), the component should be discarded and replaced. Technical specifications Mask setting options For AirSense or AirCurve: Select ‘Full Face'. Compatible devices For a full list of compatible devices for this mask, see the Mask/Device Compatibility List at ResMed.com/downloads/masks. Pressure-flow curve: Pressure Flow (L/min) (cm H...
  • Page 8 Magnets used in this mask are within ICNIRP guidelines for general public use. Service life The service life of the AirFit F30 mask system is dependent on the intensity of usage, maintenance, and environmental conditions to which the mask is used or stored. As this...

  • Page 9: Reprocessing The Mask Between Patients

    Reprocessing the mask between patients Only Sleep Lab Mask (SLM) variants of the AirFit F30 mask system are intended for multi-patient re-use. When using between patients, these masks must be reprocessed according to cleaning and disinfection instructions available on ResMed.com/downloads/masks.

  • Page 10: Limited Warranty

    7 days. This warranty is only available to the initial consumer. It is not transferable. If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the defective product or any of its components. This limited warranty does not cover: a) any damage caused as a result of improper use, abuse, modification or alteration of the product;...
  • Page 11 Bella Vista NSW 2153 Australia See ResMed.com for other ResMed locations worldwide. AirFit, AirSense and AirCurve are trademarks and/ or registered trademarks of the ResMed family of companies. For patent and other intellectual property information, see ResMed.com/ip. © 2018 ResMed Ltd. 638135/1 2018-07 ResMed.com...

Table of Contents