Communication Device Menu Mode (Pass-Through Programming) - Honeywell ADEMCO VISTA SERIES Programming Manual

∗ ∗ ∗ ∗ 29 COMMUNICATION DEVICE MENU MODE
This mode is for programming an IP, GSM, or IP/GSM Communicator Module using an alpha keypad. Alternatively, these
options can be programmed via the AlarmNet Direct website. After programming is complete, the module must be registered
with AlarmNet before reporting via the communication device can occur. Refer to the device's instructions for registration
procedures.
NOTE: The module must be set to device address 3.
IMPORTANT: The use of an IP/GSM Communicator Module
requires an AlarmNet–I account. Please obtain the account
information from the central station prior to programming this
module.
Using an Alpha Keypad as a 7720P Programming Tool
When programming with ∗29 menu mode, the alpha
keypad mimics the functions of the 7720P Programming
Tool. See figure to right and table below for 7720P key
functions. Each key has two possible functions: a normal
function and a SHIFT function.
Normal functions: The numeric values labeled directly
on the keys and the left-hand functions shown in
diagram on the ABC keys. To perform a normal key
function, simply press the desired key.
SHIFT functions: Those functions shown in diagram
above the numerical keys and the right-hand functions
shown on the ABC keys. To perform a SHIFT key
function, press SHIFT key (D key), then press the
desired function key (shift function is indicated by the lit
READY LED).
∗ ∗ ∗ ∗ 29 IP/GSM Program Mode
Press ∗29 while in Data Field Programming mode. The following prompts appear.
E N A B L E I P / G S M ?
0 = N o , 1 = Y e s
1 = P R O G 2 = D I A G
0 = Q U I T
Normal and SHIFT key Functions While in ∗ ∗ ∗ ∗ 29 Menu Mode
Key Normal Key Function
(A) = BS/ESC [BS]: Press to delete entry
Also, can reset EEPROM defaults †
(B) = ↓/↑
[↓]: Scroll down programming
(C) = N/Y [N]: Press for "NO" answer
(D) = SHIFT Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a
key is pressed. Press again for each SHIFT function desired.
1/A [1]: For entering the number 1
2/B [2]: For entering the number 2
3/C [3]: For entering the number 3
4/D [4]: For entering the number 4
5/E [5]: For entering the number 5
6/F [6]: For entering the number 6
7/S [7]: For entering the number 7
8/T [8]: For entering the number 8
9/X [9]: For entering the number 9
[∗] / SPACE [∗]: Used to select programming options
0 [0]: For entering the number 0
[#] / ENTER [#] / ENTER: Press to accept entries
† Active only when the "REVIEW?" prompt is displayed
Enable IP/GSM?
0 = no, not using IP or GSM;
1 = yes using IP and/or
GSM module
[∗] to continue
[Default = 0 (no IP and/or GSM)]
Programming /
Diagnostics Select
1= Prog (program the
IP/GSM options)
2 = Diag (diagnostic mode)
0 = Quit; returns to data field
programming mode
(Pass-Through Programming)
(A)
ARMED BS/ESC
(B)
READY
(C)
SHIFT
FUNCTION
(D)
WHEN LIT
7720P Emulation Template for Alpha Keypads
If using a communication device, enter 1 at this prompt and
enter 1-Prog at the next prompt to program the device. Use the
communication device's Installation Guide for details of the
device's programming prompts and instructions for registration.
Fixed-Word Keypad Note: Although programming IP/GSM
options cannot be done via a fixed-word keypad, IP/GSM can be
enabled by doing the following:
Enter ∗ ∗ ∗ ∗ 29 (to enter IP/GSM menu mode), then press 1 + [∗ ∗ ∗ ∗ ] + [∗ ∗ ∗ ∗ ]
Select whether you want to program the communication device
or enter the device's diagnostic mode.
Diagnostic Mode Note: Diagnostic mode option available only
for communicators with firmware version 2.4.16 or higher.
SHIFT Key Function
[ESC]: Press to quit Program Mode
[↑]: Scroll up programming
[Y]: Press SHIFT-Y for "YES" answer
[A]: Used for entering C.S. ID number
[B]: Used for entering C.S. ID number
[C]: Used for entering C.S. ID number
[D]: Used for entering C.S. ID number
[E]: Used for entering C.S. ID number
[F]: Used for entering C.S. ID number
[S]: Press to display diagnostic status
[T]: Press to send TEST messages
[X]: Press to reset the IP/GSM
[SPACE]: Not used
No SHIFT function
– 34 –
A B C
1 2 3
OFF AWAY STAY
D E F
5 6
4
/
MAX TEST BYPASS
S T X
7 8 9
N / Y
INSTANT CODE CHIME
SPACE ENTER
#
0
SHIFT
READY
6160-7720P-001-V0