Honeywell VISTA 15P - Ademco 6 Zone Control Panel User Manual
Ademco vista series
Hide thumbs
Also See for VISTA 15P - Ademco 6 Zone Control Panel:
- Installation and operation manual (40 pages) ,
- Installation manual (24 pages)
Related Manuals for Honeywell VISTA 15P - Ademco 6 Zone Control Panel
Summary of Contents for Honeywell VISTA 15P - Ademco 6 Zone Control Panel
- Page 1 ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V4 10/04 Rev. A National Security Systems Inc (800) 457-1999...
-
Page 2: About This Manual
Use of any such unauthorized device may cause damage or compromise the performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have been thoroughly tested to ensure optimum performance when used with your Honeywell security system. -
Page 3: Table Of Contents
Table of Contents System Overview ............................5 Introduction ............................5 System Basics ............................ 5 Using the Voice Message Center ...................... 7 About The Keypads ..........................8 General Information.......................... 8 Fixed-Word Display Keypad ......................10 Functions of the Keypads ........................11 Entry/Exit Delays ........................... - Page 4 Table of Contents (continued) Macro Key Programming & Usage ......................27 About Macro Keys ........................... 27 Example of Macro Programming ....................28 Using a Programmed Macro Key ....................28 Using Device Commands........................29 Paging Feature ............................30 About Automatic Paging ......................... 30 About Manual Paging........................
-
Page 5: System Overview
System Overview Introduction Congratulations on your ownership of a Honeywell Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. This system provides: • Three forms of protection: burglary, fire* and emergency •... - Page 6 System Overview (cont’d) Zones and Partitions • The system sensing devices have been assigned to various “zones,” which are specific areas of protection (e.g., front door, kitchen window, etc.). • Zone numbers are displayed at the keypad when an alarm or trouble condition occurs on a sensor.
-
Page 7: Using The Voice Message Center
System Overview (cont’d) Function Keys • The “A,” “B,” “C,” and “D” keys can be programmed to perform various functions. • Functions include: activate a panic alarm, arm the system, provide step arming, switch lights on/off, send a message to a pager, display Time/Date, and start a programmed Macro sequence. -
Page 8: About The Keypads
About The Keypads General Information Your keypads allow you to control all system functions and feature the following: • A telephone style (digital) keypad • Liquid Crystal Displays (LCD) that show the nature and location of all occurrences • Built-in sounder that sounds during alarms and troubles. The sounder also "beeps" during certain system functions and also when depressing any of the keys (to acknowledge the key press). - Page 9 About The Keypads (cont’d) ARMED ARMED AWAY STAY AWAY STAY READY READY TEST BYPASS TEST BYPASS CODE CHIME INSTANT CODE CHIME INSTANT READY READY Standard Alpha Display Keypad Standard Fixed-Word Display Keypad ARMED AWAY STAY RECORD VOLUME PLAY READY TEST BYPASS MESSAGE INSTANT...
-
Page 10: Fixed-Word Display Keypad
About The Keypads (Cont’d) FIXED-WORD DISPLAY KEYPAD AWAY: All burglary zones, interior and AWAY NIGHT NO AC perimeter, are armed. PHONE TEST BYPASS Perimeter burglary zones, such as STAY: NOT READY STAY ALARM CHIME BAT protected windows and doors, are FIRE CHECK INSTANT... -
Page 11: Functions Of The Keypads
Functions of the Keypads ARMED STAY AWAY RECORD VOLUME PLAY READY TEST BYPASS MESSAGE CODE CHIME INSTANT READY STATUS VOICE FUNCTION Voice-capable 2-line Alpha keypad (shown with flip-down front door removed) IMPORTANT! • Match the numerical callouts in the above graphic with the corresponding number on the following pages for a description of usage. - Page 12 Functions of the Keypads (cont’d) [PLAY] On Voice keypads, used in NOTE: The functions printed directly on the keys indicate their primary purpose; conjunction with the FUNCTION and functions printed under some of the keys (shown VOICE keys to play the recorded in brackets under the respective key), indicate message.
- Page 13 Functions of the Keypads (cont’d) 15. MIC 11. # This key can be used for "Quick voice keypads, microphone Arming" of the system without use of a Message Center recordings. security code (if programmed). 16. MESSAGE LED INDICATOR: (RED) [FUNCTION] On Voice keypads, enables On Voice keypads, flashes red when the desired voice or volume function.
-
Page 14: Entry/Exit Delays
Entry/Exit Delays Entry Delay Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the keypad to disarm the system. -
Page 15: Exit Alarms
Entry/Exit Delays (cont’d) Exit Alarms Exit Error Conditions Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted before exit delay expires and remains faulted (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message "ALARM CANCELED "... -
Page 16: Checking For Open Zones
Checking For Open Zones Using the [∗ ∗ ∗ ∗ ] Key to Display and Announce System Status efore arming your system, all protected doors, windows and other protection zones must be closed or bypassed; otherwise the keypad will display a "Not Ready" message. -
Page 17: Arming The System
Arming the System STAY Mode: Arms Perimeter Only, Entry Delay On • Used when you want to arm the system with persons staying inside (or if you have pets that are moving throughout the premises). • The perimeter sensors are armed, but interior sensors are left disarmed. •... -
Page 18: Arming Commands
Arming the System (cont’d) Arming Commands Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed. Mode Press these keys… Keypad Confirms By… • three beeps † security code + STAY STAY •... -
Page 19: Single Button Arming
Arming the System (cont’d) Single Button Arming The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for single-button arming. Note that while it is not necessary to use a security code for arming (by using the Quick Arm method described previously), a security code must always be used when manually disarming the system. -
Page 20: Keyswitch
Keyswitch Using the Keyswitch Your system may be equipped with a keyswitch for use when arming and disarming. Red and green lights on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones). -
Page 21: Disarming And Silencing Alarms
Disarming and Silencing Alarms Using the [OFF] key The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear alarm memories. IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence. -
Page 22: Bypassing Protection Zones
Bypassing Protection Zones Using the BYPASS Key Use t his key when you want to arm your system with one or more zones intentionally unprotected. The system must be disarmed first. Vent Zones: Your system may have certain windows set as “vent” zones, which are automatically bypassed if left open when arming the system (you do not need to manually bypass them). -
Page 23: Quick Bypass
Bypassing Protection Zones (cont’d) Quick Bypass If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night. Alpha Display: + [#] BYPASS... -
Page 24: Chime Mode
Chime Mode Using the Chime Mode CHIME mode alerts you to the opening of a perimeter door or window while the system is disarmed. When Chime mode is activated: • Three tones sound at the keypad whenever a perimeter door or window is opened. •... -
Page 25: Date And Time
Date and Time Viewing the Current Date and Time The system lets you view its time and date setting on an alpha keypad. Alpha Display: + [#] + [6] [3] ∗∗∗∗DISARMED∗∗∗∗ (Security Code) READY TO ARM Press the function key (A, B, C, or D) for viewing current date and time, if programmed. -
Page 26: Panic Keys
Panic Keys Using Panic Keys Your system may have been programmed to use special keys to manually activate emergency (panic) functions as follows: This Function Sends This Signal* With This Sounding… Silent Alarm silent alarm no audible alarm; displays, “Press [∗] to show faults,”... -
Page 27: Macro Key Programming & Usage
Macro Key Programming & Usage About Macro Keys The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of commands of up to 16 keystrokes, if programmed for this function. These keystrokes, as a group, are called “macros” and are stored in the system's memory. •... -
Page 28: Example Of Macro Programming
Macro Key Programming & Usage (cont’d) The keypad beeps to acknowledge your input and displays the command you entered (followed by “F”). 4. Enter the next command, followed by press/holding the “D” key for at least two seconds. The keypad beeps and displays the keystrokes entered so far. 5. -
Page 29: Using Device Commands
Using Device Commands About Device Commands Your system may be set up so that it can control certain lights or other devices. • Some devices may be automatically turned on or off by the system. • You may be able to override automatically controlled devices using the commands described below. -
Page 30: Paging Feature
Paging Feature About Automatic Paging Your system may be set up to automatically send messages to several pagers (4 pagers for VISTA-20P Series, 2 pagers for VISTA-15P Series) as certain conditions occur in your system. • The following events can be programmed by your installer to be sent to the pagers: arming and disarming †... -
Page 31: About Manual Paging
Paging Feature (cont’d) About Manual Paging Your system may be set up so you can manually send a message to up to four (VISTA- 20P Series) or two (VISTA-15P Series) pagers. • Your installer programs the paging function key and the pager phone numbers. •... -
Page 32: Security Codes & Authority Levels
Security Codes & Authority Levels About Security Codes Your installer assigned a master code that is used to perform all system functions. In addition, you can assign different security codes for use by other users (VISTA-20P Series provides 47 additional codes; VISTA-15P Series provides 31 additional codes). •... -
Page 33: How To Assign User Codes And Attributes
Security Codes & Authority Levels (cont’d) How to Assign User Codes and Attributes The following lists the various command strings for adding user codes and attributes. Refer to the User Setup chart at the back of this manual for factory defaults of user attributes and to keep a record of user programming. -
Page 34: Accessing Other Partitions (Vista-20P Series)
Accessing Other Partitions (VISTA-20P) About Accessing Partitions (GOTO Command and Multi-Partition Arming) Each keypad is assigned a default partition for display purposes, and will show only that partition's information. • If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. -
Page 35: Using The Goto Command
Accessing Other Partitions (cont’d) Using the GoTo Command (VISTA-20P) If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. • You must use an Alpha keypad to access another partition. •... -
Page 36: Common Zone Operation (Vista-20P Series)
Accessing Other Partitions (cont’d) Common Zone Operation (VISTA-20P) Your system may have been set up to use a common zone, which is Ask your installer if a an area shared by users of both partitions, such as a foyer or lobby. "common zone"... -
Page 37: Scheduling
Scheduling About Scheduling The system provides end-user schedules (programmable by master/installer only), which can control various types of events. • Each schedule causes a defined event to start and stop (when appropriate) at a specified time. • Schedules can be set to automatically repeat at various intervals. •... - Page 38 Scheduling (cont’d 5. For event number “02,” enter the access group GROUP NUMBER number. Otherwise, this prompt is skipped. Press [∗] to continue to the “Start” prompt below. 6. For event numbers “03-07,” enter the partition PARTITION number to be armed or disarmed. 0 = arm all;...
-
Page 39: Event Logging Procedures
Event Logging Procedures About Event Logging The system records various events in a history log, which can be viewed by the master user on an Alpha Display keypad. • The Event Log holds up to 100 (VISTA-20P Series) or 50 (VISTA-15P Series) events. •... - Page 40 Event Logging Procedures (cont’d) Code Definition Code Definition Alarm, Expansion Module Disarmed, Armed AWAY, Armed STAY ECP Module cover tamper Schedule Arm/Disarm AWAY Silent Burglary Cancel by User Alarm, 24-Hour Auxiliary/Monitor zone Remote Arm/Disarm (Downloading) Carbon Monoxide Quick Arm AWAY AC Power Keyswitch Arm/Disarm AWAY Low System Battery/Battery Test...
-
Page 41: Testing The System
Testing the System About Testing the System Using the Test mode allows each protection point to be checked for proper operation. Testing should be conducted weekly to ensure proper operation. • The keypad sounds a single beep about every 30 seconds as a reminder that the system is in the Test mode. -
Page 42: Trouble Conditions
Trouble Conditions "Check" and he word CHECK on the keypad's display, accompanied by a "Battery" Displays "beeping" at the keypad, indicates a trouble condition in the system. To silence the beeping for these conditions, press any key. 1. A display of "CHECK" and one or more zone numbers indicates that a problem exists with the displayed zone(s) and requires your attention. - Page 43 Trouble Conditions (cont’d) Words or letters in parentheses ( ) are those that are displayed on Fixed-Word Display keypads. Other Trouble COMM. FAILURE Indicates that a failure has occurred in Displays (or FC) the telephone communication portion of your system. CALL FOR SERVICE. SYSTEM LO BAT Indicates that a low system battery (or BAT with no...
- Page 44 Trouble Conditions (cont’d) Other Trouble AC LOSS The system is operating on battery power Displays (or NO AC) only due to an AC power failure. (Continued) If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. If AC power cannot be restored and a “low system battery”...
-
Page 45: Maintaining Your System
Maintaining Your System Taking Care of The components of your security system are designed to be as Your System maintenance-free as possible. However, to make sure that your system is in reliable working condition, do the following: 1. Test your system weekly . 2. -
Page 46: Fire Alarm System
Fire Alarm System THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. - Page 47 Fire Alarm System (cont’d) THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS Manually 1. Should you become aware of a fire emergency before your smoke or heat detectors sense the problem, go to your nearest keypad and Initiating manually initiate an alarm by pressing the panic key assigned for a Fire Alarm FIRE emergency for 2 seconds (see below).
-
Page 48: National Fire Protection Association Recommendations On Smoke Detectors
Fire Alarm System (cont’d) THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS National Fire Protection Association Recommendations on Smoke Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72) noted below. -
Page 49: Emergency Evacuation
Fire Alarm System (cont’d) THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS Emergency Evacuation • – 49 –... -
Page 50: Quick Guide To Basic System Functions
Quick Guide to Basic System Functions FUNCTION PROCEDURE COMMENTS Check Zones Press READY key. View faulted zones when system not ready. Enter code. Press arming key desired: Arms system in mode selected. Arm System (AWAY, STAY, NIGHT-STAY, MAXIMUM, INSTANT) Press #. Press arming key desired: Arms system in mode selected, quickly Quick Arm (AWAY, STAY, MAXIMUM, INSTANT) -
Page 51: Summary Of Audible/Visual Notifications
Summary of Audible/Visual Notifications Fixed-Word Display Keypads SOUND CAUSE DISPLAY LOUD, FIRE ALARM FIRE is displayed; zone number of zone in INTERRUPTED * alarm is displayed. If a fire alarm is manually activated, zone number 95 will be Keypad & Ext. displayed. -
Page 52: Alpha Display Keypads
Summary of A/V Notifications (cont’d) Alpha Display Keypads SOUND CAUSE DISPLAY LOUD, FIRE ALARM. FIRE is displayed; descriptor of zone in alarm is INTERRUPTED* displayed. If a fire alarm is manually activated, zone Keypad & Ext. number 95 will be displayed. LOUD, BURGLARY/AUDIBLE ALARM is displayed. -
Page 53: Regulatory Statements And Warnings
Regulatory Statements and Warnings WARNING: This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15 This device complies with part 15 of the FCC rules. - Page 54 Regulatory Statements (cont’d) Industrie Canada AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à...
-
Page 55: System Features
System Features Log Features Comments Exit Delay Part. 1: Part. 2 Entry Delay 1 Part. 1: Part. 2 Entry Delay 2 Part. 1: Part. 2 NIGHT-STAY Zones Zones: Quick Arm Quick Bypass Automatic Paging users: Keyswitch Arming Arm AWAY: steady flash (circle type of LED lighting) Arm STAY:... -
Page 56: User Setup
System Features Log (cont’d) User Setup The following chart will help keep track of system users. Copies should be distributed to the † † partition 1 and partition 2 (if applicable) masters for their records. To program a user attribute: Enter system/partition* master code + [8] + user no. -
Page 57: Paging Setup
System Features Log (cont’d User Setup (cont’d) Enter system/partition master code + [8] + user no. + “#” command listed in column heading. User User User’s Part(s). Security Auth. Access RF Zone Pager Name (system master only) Code Level Group Number on/off [#] [3] + part(s) + [#]... -
Page 58: List Of Output Devices
System Features Log (cont’d Schedules*: master code + [#] + [6] [4] Event Device No. Group No. Partition Start Stop Repeat Random Time/ Time/ (see list below) for “01” events: for “02” events: for “04-06” events: (1-4) (yes/no) enter 1-8 enter 1, 2, or 3 (see device list below) Events:... -
Page 59: Owner's Insurance Premium Credit Request
OWNER’S INSURANCE PREMIUM CREDIT REQUEST This form should be completed and forwarded to your homeowner’s insurance carrier for possible premium credit. A. GENERAL INFORMATION: Insured’s Name and Address: Insurance Company: Policy No.: VISTA-20P / VISTA-15P Other _____________________________________________________ (circle the appropriate model number) Type of Alarm: Burglary Fire... - Page 60 OWNER’S INSURANCE PREMIUM CREDIT REQUEST (cont.) E. SMOKE DETECTOR LOCATIONS Furnace Room Kitchen Bedrooms Attic Basement Living Room Dining Room Hall F. BURGLARY DETECTING DEVICE LOCATIONS: Front Door Basement Door Rear Door All Exterior Doors Floor Windows All windows nterior locations All Accessible Openings, Including Skylights, Air Conditioners and Vents G.
- Page 61 – Notes – – 61 – National Security Systems Inc (800) 457-1999...
- Page 62 – Notes – – 62 – National Security Systems Inc (800) 457-1999...
-
Page 63: Limitations Of This System
LIMITATIONS OF THIS SYSTEM WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. -
Page 64: Warranty
ONE YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or workmanship under normal use and service.