Power requirements ..................13 Connecting fixtures ....................13 Data network requirements ................14 Setup ........................15 RDM and Martin® M-PC ................... 15 Step one: scanning for devices on the data link ..........15 Setting DMX mode .................... 15 Setting DMX addresses ..................15 Dimming control ....................
It can create a fire hazard or a risk of eye injury if the safety precautions below are not followed. Install, operate and service RUSH® by Martin® products only as directed in their user manuals, or you may create a safety hazard or cause damage that is not covered by product warranties.
Page 6
Do not modify the fixture in any way not described in this manual or install other than genuine Martin® parts. Do not stick filters, masks or other materials onto any lens or other optical component. Use only accessories approved by Martin® to modify the light beam.
Page 7
GRAZE fixtures The CS Series Graze fixtures fall into the following risk groups according to EN62471 at the distances indicated below. Position the CS Series Graze fixtures so that prolonged staring into the light output at less than 2.4 m (7.9 ft.) from the fixture is not expected. 2.4 m 23.5 m (7.9 ft.)
Introduction The RUSH® CS Series from Martin® is a line of rugged LED-based lighting fixtures with a remote power supply unit. Fixtures are available in 300 mm (1 ft.), 600 mm (2 ft.), 900 mm (3 ft.) and 1200 mm (4 ft.) length models, each with either wide or graze optics.
Fixture overview Number Description Mounting bracket Tilt lock screws Power/data input connector (blue) Power/data output connector (black) RUSH® CS Series LED fixture parts Identification Number Description Mains power input (Fuse: T6.3A) DMX input DMX output Mains power indicator light Data/power output to fixtures RUSH®...
Page 10
Fixture output Fixture input (blue) Power supply output Number Description Data ground Data - Data + Not used Not used +36 V power Not used 0 V power RUSH® CS Series combined power/data connector The 5-pin XLR connectors for DMX use standard pinout. Pin Number Description Data ground...
All local safety regulations and legal requirements must be observed when installing and connecting the RUSH® CS Series. Installation must be carried out by qualified professionals only. Contact your Martin supplier for assistance if you have any questions about how to install this product safely. Fixture location RUSH®...
Page 12
You can slide the mounting brackets along the fixture by loosening the slide grubscrew (1) using a 2mm hex key (not supplied). Ensure that the grubscrew is re-tightened to lock the bracket in the desired position. You can reverse the orientation of the mounting brackets so that the flanges face inwards by removing the M6 hex-head bolts (2) and washers (3).
AC power and data connection to PSU Warning! Read ‘Safety information’ on page 5 before installing the fixtures and PSU. Electrical installation must be carried out by qualified professionals only. Lock out power to the entire installation before working on cables and connections. For protection from dangerous electric shock, the PSU must be grounded (earthed).
• Branches may be added to the link using an opto-isolated splitter. Use an RDM-compatible amplifier- splitter such as the Martin® RDM 5.5 Splitter. Each branch may itself connect up to 32 fixtures. • An RDM amplifier may also be used to extend a network beyond 500 meters (1640 ft.) or to connect up to 32 additional fixtures to the daisy chain.
PC that is connected to the installation via a DMX data link. To use Martin® M-PC, connect a PC running the application to the data link via a USB-to-DMX interface box such as the Martin® M-DMX (see ‘Related Items’ on page 23).
To set a DMX address: In Martin® M-PC, go to RDM CONTROLLER Scan Properties Advanced Choose PID Set DMX START ADDRESS. In the Message column, enter the DMX address that you want to give to the fixture (or give to all the fixtures if you are sending a broadcast command).
The light source in this product is not user-replaceable. When the light source LEDs reach the end of their service life, they may be replaced only by Martin® Service, an authorized Martin® Service agent or a similarly qualified person.
DMX protocol 6-channel mode The DMX control allows 0 to 100% intensity control of red, green and blue. 0 to 100% master dimming is provided using 16-bit control (two DMX channels). The final control channel allows five fixed color temperatures of white light to be produced – when this channel is set to a value above zero, the Red, Green and Blue control channels are overruled and have no effect.
Specifications Physical CS300 Wide Length ..........................303 mm (11.9 in.) Width ........................... 46 mm (1.8 in.) Height ...................... 57 mm (2.2 in.) including bracket Weight ..........................0.8 kg (1.8 lbs.) CS300 Graze Length ..........................303 mm (11.9 in.) Width ........................... 46 mm (1.8 in.) Height ......................
Page 22
Beam angle ........................... 18° x 65° Minimum LED lifetime ..............50 000 hours (to >70% luminous output)* *Figure obtained under manufacturer's test conditions See www.martin.com for full photometric specifications. Construction Housing ............................Aluminum Finish ..................Clear anodized (standard) or white (optional) Lens .........................
Page 23
RUSH® CS900 Graze, 18°x 65° (3 ft., RGB) ............... P/N 90480190 RUSH® CS1200 Graze, 18°x 65° (4 ft., RGB) ..............P/N 90480200 Power Supply Unit RUSH® CS Series PSU ....................... P/N 90480210 Specifications subject to change without notice. For latest product specifications, see www.martin.com RUSH® CS Series User Manual...
Page 24
Disposing of this product Martin® products are supplied in compliance with Directive 2012/19/EC of the European Parliament and of the Council of the European Union on WEEE (Waste Electrical and Electronic Equipment), where applicable. Help preserve the environment! Ensure that this product is recycled at the end of its life.