Using The Assemble Edit Function; Recording From Another Vcr Or Camcorder; Using The Tv Buttons On The Remote Control - Samsung DVD-V70 Instruction Manual

VCR

Using the Assemble Edit Function

This function allows you to start a new recording at a specific
position on the cassette while maintaining a very smooth scene
change.
1
GB
2
4
3
4
2
5
OK
6
7
8
VCR
Recoding from Another VCR or Camcorder
You can copy a cassette to your DVD-VCR from another video
source, such as another VCR or a camcorder.
EJECT
STANDBY/ON PROG DVD VCR LINE2
1
2
2
3
4
7
5
6
OK
7
46
Insert the cassette to be edited in your DVD-VCR.
❿
Press the ll button to start playback.
When you reach the position from which you wish to start the new
❿
recording, press the ll button.
Press the F.ADV/STEP ( ) button again as often as
necessary to advance frame by frame, until the exact recording
position is located.
While the DVD-VCR is in still mode, hold the REC button ( )
down for a while to activate the Assemble Edit function.
Select the source from which you wish to record by pressing:
The PROG ( or ) buttons for television channels
The INPUT SEL. button for the LINE input sources
❿
Press the ll button to start recording.
When you have finished recording, press .
It is an infringement of copyright laws to copy prerecorded
cassettes or to re-record them in any form without the
permission of the owners of the corresponding copyright.
Connect the DVD-VCR, from which the cassette is to be copied, to
the appropriate RCA audio and video input connectors on the
rear of your DVD-VCR, as indicated on page 14.
Insert a blank cassette in your DVD-VCR.
Insert the pre-recorded cassette in the other video source (VCR or
camcorder).
Press the INPUT SEL. button to select the appropriate input on
your DVD-VCR: LINE IN for the RCA input.
Start playing back the cassette to be copied.
Hold REC ( ) down for a while to start recording on your
DVD-VCR.
When you have finished recording, press on both VCR and
DVD-VCR.
If you wish to view the cassette being copied:
Your DVD-VCR must be connected as usual to the
television (see page 13 for further details)
Using the TV Buttons on the Remote Control (DVD-V80/ DVD-V85)
Your DVD-VCR remote control will work with Samsung televisions
and compatible brands.
To determine whether your television is compatible, follow the instructions
below.
1
Switch your television on.
2 Point the remote control towards the television.
3 Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand Codes Brand Codes
SAMSUNG 01 to 06 PHILIPS 02, 20, 22
AKAI 09, 23 SABA 13, 14, 22 to 24
GRUNDIG 09, 17, 21 SONY 15, 16
LOEWE 02 THOMSON 13, 14, 24
PANASONIC 08, 23 to 27 TOSHIBA 07, 16 to 19, 21
Result: If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
When you change the batteries in the remote control, you
must reprogramme the code, following the same procedure.
You can then control the television using the following buttons.
Button Function
STANDBY/ON Used to switch the television and DVD-VCR on and off.
TV or VCR Used to switch between the TV and VCR modes.
INPUT SEL. Used to select an external source.
+ –
VOL or Used to adjust the volume of the television.
PROG/TRK Used to select the required programme.
( or )
TV MUTE Used to mute the volume of the television.
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
VCR
STANDBY/ON OPEN/CLOSE
1
GB
2
2
4
3
4
5
5
6
47