Mira Discovery Installation & User Manual
Shower fittings
Hide thumbs
Also See for Discovery:
- Installation and user manual (44 pages) ,
- Installation and user manual (40 pages) ,
- Installation and user manual (25 pages)
Related Manuals for Mira Discovery
Summary of Contents for Mira Discovery
- Page 1 SHOWER FITTINGS Installation & User Guide THESE INSTRUCTIONS ARE TO BE LEFT WITH THE USER...
-
Page 2: Table Of Contents
Contents Section Page 1 ..Introduction ..............3 2 ..Important Safety Information ........... 4 3 ..Pack Contents Checklist ..........5 4 ..Dimensions ..............7 5 ..Specifications ..............8 6 ..Installation Requirements ..........9 7 ..Installation .............. -
Page 3: Introduction
Mira shower fittings are precision engineered to give a satisfactory shower over a range of pressures. The fittings are suitable for pressures up to 5.0 bar and pressures down to 0.05 bar. -
Page 4: Important Safety Information
Section Important Safety Information 1. WARNING! Products manufactured by us are safe and without risk provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations. 2. Caution! 2.1. Read all of these instructions. 2.2. -
Page 5: Pack Contents Checklist
Section Pack Contents Checklist Tick the appropriate boxes to familiarise yourself with the part names and to confirm that the parts are included. Shower fittings 2 x Bracket 2 x Fixing Screw 1 x Handset 1 x Slide Bar 1 x Hose 2 x Hose Washers 1 x Clamp Bracket Assembly... - Page 6 Section Pack Contents Checklist Tick the appropriate boxes to familiarise yourself with the part names and to confirm that the parts are included. Shower fittings BIV - Built-In Variable Right Angle Connector Fittings Pack 1 x Wallplate 1 x Backplate 1 x Olive 2 x 'O' Seals 2 x Wall Plug...
-
Page 7: Dimensions
Section Dimensions 75.5 NOTE:- NOT TO SCALE - Dimensions are nominal and in millimetres... -
Page 8: Specifications
Warning! Exceeding the stated maximum maintained pressure could result in excessive spray forces and possible damage to the handset. Pressure loss = Pressure difference between the inlet and outlet of the fitting. Mira Discovery adjustable range flow rates - Low capacity nozzle rings fitted Start Soothe... -
Page 9: Installation Requirements
Section Installation Requirements 1. Plumbing Read the section “Important Safety Information” first. 1.1. Supply pipework MUST be flushed to clear debris before connecting the appliance. 1.2. A hose retaining ring is supplied to prevent the handset from dropping below the spill-over level of the bath or shower, which could lead to contamination from back siphonage. -
Page 10: Installation
Section Installation 1. Mira Discovery ev - Exposed Variable Shower Fittings Solid, dry-lined, stud partition, shower cubicle or laminated panel walls Read the section “Installation Requirements” first. The slide bar should be fixed to the wall to one side of the product and at a convenient height for all the family. - Page 11 1.3. For solid walls drill two 8.0 mm diameter holes at 600 mm centres and insert the wall plugs. Screw Note! Special consideration should be given to the fixing arrangements when installing on to a dry lined, Bracket stud partition, shower cubicle or Bracket Cover laminated panel wall structures.
- Page 12 2. Mira Discovery biv - Built-in Right Angle Connector (RAC) Read the section “Installation Requirements” first. The right angled connector assembly (RAC) for use with built-in shower controls, should be positioned above and offset from the top outlet of the shower control. This will prevent the flexible hose from obstructing the temperature and flow controls used to operate the shower.
- Page 13 2.7. Drill the two RAC wallplate fixing holes, if necessary make a recess Foam Seal approximately 6 mm deep to accept the RAC wallplate. Plug the two fixing holes. 2.8. Fix the RAC wallplate to the wall with the two fixing screws. 2.9.
- Page 14 3. Mira Discovery bir - Built-in Rigid Shower Fittings Solid, dry-lined, stud partition, shower cubicle or laminated panel walls Read the section “Installation Requirements” first. The bir spray head should be positioned at a convenient height for all the family. It...
-
Page 15: Operation
Section Operation 1. Spray action The handset spray head has four different spray actions:- start, combination, calm, combination and blast setting. The handset operation is described below. To access the eco setting, turn the spray plate fully clockwise. Water will flow from the outer set of holes and the flow rate will be reduced. -
Page 16: Maintenance
2. Height and direction adjustment Locking Wheel Clamp Bracket Assembly Section Maintenance 1. Cleaning Many household cleaners contain abrasives and chemical substances, and should not be used for cleaning plated or plastic fittings. These finishes should be cleaned with a mild washing up detergent or soap solution, and then wiped dry using a soft cloth. Handset spray plate - external 1.1. -
Page 17: Fault Diagnosis
Section Fault Diagnosis Read the section “Important Safety Information” first. Provided that the shower fitting has been correctly installed and is operated in accordance with the instructions contained in this guide, difficulties should not arise. If any maintenance is required then it must be carried out by a competent tradesperson for whom the fault diagnosis chart and maintenance instructions are provided. -
Page 18: Spare Parts
Section Spare Parts 1. Adjustable Fittings Spare parts list 1595.030 Handset 1595.034 Slide Bar Support Assembly (components marked 'A') 1595.033 Clamp Bracket Assembly 1595.077 Screw Pack (components marked 'B') 150.58 Hose 1595.074 Slide Bar 1595.073 Hose Retainer 632.73 Hose Washer 1595.035 Right Angle Connector (RAC) Shroud 450.20... - Page 19 Adjustable Fittings Spare parts diagram 632.73 1595.033 1595.074 1595.030 1595.032 450.20 1595.031 632.73 1595.071 150.58 1595.035 1595.073...
- Page 20 Note! In the interests of safety, spares requiring exposure to mains To be free of charge, service work must only be undertaken by Mira voltages can only be sent to competent persons.