Planet GSD-504 User Manual

1. Package Contents
Check the contents of your package for the following
parts:
Gigabit Ethernet 5V DC User's
Switch x 1 1A Power Manual x 1
Adapter x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
- 1 -
2. Product Features
RJ-45 Interface
 5/8 10/100/1000Mbps Gigabit Ethernet ports
 Complies with IEEE 802.3, 10Base-T, IEEE 802.3u
100Base-TX, IEEE 802.3ab 1000Base-T
 Supports Auto MDI/MDI-X function
Switching
 Hardware based 10/100Mbps, Half / Full Duplex and
1000Mbps Full Duplex mode, Flow Control and Auto-
negotiation
 Features Store-and-Forward mode with wire-speed
filtering and forwarding rates
 IEEE 802.3x flow control for Full Duplex operation
and backpressure for Half Duplex operation
 Integrated address look-up engine, supporting 2K/8K
absolute MAC addresses (GSD-504 / GSD-804)
 9K Jumbo packet size
 Power Saving ability for Green networking
 Automatic Address Learning and Address Aging
 Supports CSMA/CD protocol
- 2 -
Hardware
 Made from plastic and desktop size and wall-mount
design
 LED indicators for system power, per port Link / Act
 5V DC, 1A external power adapter
 FCC, CE Class B compliant
- 3 -
3. Switch Top Panel
Figures 3-1 and 3-2 show the top panel of GSD-504
and GSD-804, respectively.
Figure 3-1: GSD-504 Top Panel
Figure 3-2: GSD-804 Top Panel
- 4 -
4. LED Indicators
Figures 4-1 and 4-2 show the front panel of GSD-504
and GSD-804, respectively.
Figure 4-1: GSD-504 LED Panel
Figure 4-2: GSD-804 LED Panel
LED Color Function
Indicates that the Switch is
Light
powered ON.
PWR Green
Indicates that the Switch is
OFF
powered OFF.
Indicates the link
through that port is
Light
successfully established at
10/100/1000Mbps.
Link/ACT Green
Indicates the Switch is
Blink actively sending or receiving
data over that port.
- 5 -
5. Switch Rear Panel
Figures 5-1 and 5-2 show the rear panel of GSD-504
and GSD-804, respectively.
5 4 3 2 1
Figure 5-1: GSD-504 Rear Panel
8 7 6 5 4 3 2 1
Figure 5-2: GSD-804 Rear Panel
- 6 -
1. The device is a power-required device,
meaning it will not work till it is powered.
If your networks should be active all the
time, please consider using UPS (Uninter-
rupted Power Supply) for your device. It
will prevent you from network data loss
or network downtime.
Power
Notice
2. In some areas, installing a surge sup-
pression device may also help to protect
your Switch from being damaged by un-
regulated surge or current to the Switch
or the power adapter.
- 7 -
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please read the
following topics and perform the procedures in the order
being presented.
This Switch does not need software configu-
ration.
Note
 Desktop Installation
To install the Switch on desktop, simply follow the
following steps:
Step 1: Place the Switch on the desk near a power
source.
Step 2: Keep some ventilation space between the
Switch and the surrounding objects.
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 under Product Specifi-
Note
cations.
- 8 -