Sharp TQ-GX30E Service Manual page 139

Pin No. Terminal name
57 SUBDB0
58 SUBDB2
59 HSD5
60 DB0
61 HSD4
62* EXCS_B2
63 GDATA[5] (G5)
64 GDATA[4] (G4)
65 GDATA[3] (G3)
66 SUBDB3
67 SUBDB4
68 HSD7
69 DB1
70 DB2
71 DB3
72 DB4
73 STKCHK
74 VDDCORE
75 GND
76 VDDIO
77 GDATA[2] (G2)
78 SUBDB5
79 BSCLK
80 SUBCK
81 DB5
82 VDDIO
83 GND
84 VDDCORE
85 CAMCK
86 GDATA[1] (G1)
87 GDATA[0] (G0)
88 RDATA[5] (R5)
89 RDATA[4] (R4)
90 VDDCORE
91* PWMLCD/PORT4
92 BSBLK_B
93 DB6
94 DB7
95 DB8
96 DB9
97 VDDIO
98 RDATA[3] (R3)
99 RDATA[2] (R2)
100 RDATA[1] (R1)
101 RDATA[0] (R0)
102* MP4_P0
103* EXCS_B0
104 BSPIXEL7
105 BSVS_B
106 DB10
107 DB11
108 DB12
109* MP4_PLLCK
110 SUBDB7
111 GND
112 DA0
113 BSPIXEL0
114 DCS_B
115 VDDIO
116 BSPIXEL6
117 SE_DO/PORT0
118 DB13
Downloaded from www.Manualslib.com
CONFIDENTIAL
Input/Output
Input/Output Data bus for External display
Input/Output Data bus for External display
Input/Output Data bus for high-speed serial transfer
Input/Output Data bus
Input/Output Data bus for high-speed serial transfer
Input/Output Chip select output 2 (internal decode output) (Not used)
Output Display panel G output signal
Output Display panel G output signal
Output Display panel G output signal
Input/Output Data bus for External display
Input/Output Data bus for External display
Input/Output Data bus for high-speed serial transfer
Input/Output Data bus
Input/Output Data bus
Input/Output Data bus
Input/Output Data bus
Input Setting BS-related output terminal to Hi-z when a stack is installed
(Connected to GND normally)
– CORE Power supply 1.8 V (1.6 V~ 2.0 V)
– Logic ground
– IO Power supply 3.0 V (2.7 V~ 3.3 V)
Output Display panel G output signal
Input/Output Data bus for External display
Input/Output External Bit Stream data clock
Output Clock for External display
Input/Output Data bus
– IO Power supply 3.0 V (2.7 V~ 3.3 V)
– Logic ground
– CORE Power supply 1.8 V (1.6 V~ 2.0 V)
Output Clock for camera operation
Output Display panel G output signal
Output Display panel G output signal
Output Display panel R output signal
Output Display panel R output signal
– CORE Power supply 1.8 V (1.6 V~ 2.0 V)
Output PWM LCD output
General-purpose PORT output (default) (Not used)
Input/Output External Bit Stream data effective signal ("High" is active when transferring the data)
Input/Output Data bus
Input/Output Data bus
Input/Output Data bus
Input/Output Data bus
– IO Power supply 3.0 V (2.7 V~ 3.3 V)
Output Display panel R output signal
Output Display panel R output signal
Output Display panel R output signal
Output Display panel R output signal
Output MPEG4 control
Input/Output Chip select output 0 (internal decode output) (Not used)
Input/Output External Bit Stream data bus
Input/Output External Bit Stream vertical synchronization signal ("Low" is active)
Input/Output Data bus
Input/Output Data bus
Input/Output Data bus
Output MPEG4ASIC clock 15.36 MHz/CPU supply XIN clock (Not used)
Input/Output Data bus for External display
– Logic ground
Input/Output Address input for chip select decode
Input/Output External Bit Stream data bus
Input Chip select input dedicated for chip select decode
– IO Power supply 3.0 V (2.7 V~ 3.3 V)
Input/Output External Bit Stream data bus
Output Data output for 4-wire serial IF (default)
General-purpose PORT output
Input/Output Data bus
manuals search engine
Description of terminal
6 – 19
GX30