Sharp GX20 Service Manual

Sharp GX20 Service Manual

Digital mobile phone
Hide thumbs Also See for GX20:

Advertisement

Quick Links

CHAPTER 1. GENERAL DESCRIPTION
[1]
Specifications ................................................ 1-1
[2]
Names of parts .............................................. 1-2
[3]
Operation manual.......................................... 1-3
CHAPTER 2. ADJUSTMENTS
[1]
Adjustments
SHARP Program Support Tool (SPST)........ 2-1
[2]
SHARP RF Test tool manual ....................... 2-30
[3]
Adjustment procedures
after replacement of the parts .................. 2-36
[4]
Test points ................................................... 2-39
[5]
Troubleshooting........................................... 2-42
[6]
Specification for function test ...................... 2-64
CHAPTER 3. DISASSEMBLY AND REASSEMBLY
[1]
Servicing Concerns ....................................... 3-1
[2]
Disassembly and reassembly ....................... 3-5
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
All manuals and user guides at all-guides.com
CONFIDENTIAL
SERVICE MANUAL
(INTERNAL MODEL NAME:
TQ-GX20E/G/R/T/S/H/EP/PP/W/B/D/A/Z/Q/L/F/C)
CONTENTS
DIGITAL MOBILE PHONE
MODEL
E : For U.K.
R : For Ireland
S : For Spain
EP: For U.K. (Prepaid)
W : For Sweden
D : For Greece
Z : For New Zealand
L : For Malta
C : For Switzerland
• In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specified
should be used.
• Caution
Risk of explosion if battery is replaced by an incorrect type,
dispose of used batteries according to the instruction.
CHAPTER 4. DIAGRAMS
[1]
Block diagram ........................................ . ........4-1
CHAPTER 5. SCHEMATIC DIAGRAM AND
WIRING SIDE OF P.W.BOARD
[1]
Notes on schematic diagram ................. . ........5-1
[2]
Types of transistor and LED .................. . ........5-1
[3]
Waveforms of circuit .............................. . ........5-2
[4]
Schematic diagram/
wiring side of P.W.Board ..................... . ........5-6
CHAPTER 6. OTHERS
[1]
Function table of IC................................ . ........6-1
[2]
Function table of Camera ...................... . ......6-27
Parts Guide
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
GX20
No. S9311TQGX20/B
GX20
G : For Germany
T : For Italy
H : For Netherlands
PP: For Portugal (Prepaid)
B : For Hungary
A : For Australia
Q : For Egypt
F : For France

Advertisement

Table of Contents
loading

Summary of Contents for Sharp GX20

  • Page 1 Adjustments Types of transistor and LED ......5-1 SHARP Program Support Tool (SPST)..2-1 Waveforms of circuit ........5-2 SHARP RF Test tool manual ....... 2-30 Schematic diagram/ Adjustment procedures wiring side of P.W.Board ......5-6 after replacement of the parts ....2-36 Test points ...........
  • Page 2 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL OZ/IQ/YO/Calc GX20 Service Manual TQGX20 Market CHAPTER 1. GENERAL DESCRIPTION FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. [1] Specifications Sound: 16-polyphonic ring melodies...
  • Page 3 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 [2] Names of parts 1. Earpiece 12. End/Power Key: Ends a call, turns power on/ off. 2. Navigation Keys (Arrow Keys): 13. Keypad Moves cursor to select menu items, etc. 14. #/Flash light Key: Switches symbol screens.
  • Page 4 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [3] Operation manual (Page numbers refer to the user guide) [Optional Accessories] • Li-ion spare battery (XN-1BT11) • High capacity Li-ion battery (XN-1BT13) • Cigarette lighter charger (XN-1CL10) • Data cable (RS232C cable: XN-1DC10) •...
  • Page 5 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 1 – 4...
  • Page 6 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 1 – 5...
  • Page 7 Hereinafter, procedures are carried out in the SPST folder. 3.2.1 Starting up Connect GX20 to an operable serial port of the PC with the supplied data cable. Connect the AC charger to the Data cable. Execute the GX20 SPST.exe program in the SPST folder.
  • Page 8 3) Click the “Change Password” button in Step 1. The screen below appears and you can change SPC. Figure 3 3.3. Functions 3.3.1 Identification SPST downloads and displays the main data configured in GX20. <Operation> 1) On the SPST startup screen, press “Identity”. Figure 4 2) Connect PC and MS with a Data cable.
  • Page 9 6) IMEI will be displayed, and the following dialog box appears. Figure 5 7) Make sure GX20 is turned off and press the power key. 8) Press “OK” when **** appears on the GX20 display. 9) Make sure “Success!!” appears. Check the data and exit.
  • Page 10 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 3.3.2 User data transfer SPST saves and downloads all the following user data. 1) Connect PC and MS with a Data cable and turn on MS. 2) Activate the software. Figure 7 a) Select the COM port.
  • Page 11 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 4) If “BACKUP” is pressed, the dialog box for file selection appears. Select the file and press “Save”. Figure 9 The buttons are grayed out during the process. Firue 10 2 – 5...
  • Page 12 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL When they return to black, the process is complete. Press “END” to exit. Figure 11 5) If “RESTORE” is pressed, the following confirmation dialog box appears. Press “OK” to confirm. Figure 12 The dialog box for file selection appears.
  • Page 13 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 The buttons are grayed out during the process. The process is complete when the buttons turn black. Figure 14 3.3.3 Default setting You can reset settings to the factory default. The following will be performed: 1.
  • Page 14 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 4) Click the “OK” button, The display changes as follows: H/W CHECK ∗ GX20 ∗ ROM VERSION : 002 GX20 Diag Version. CVS A07-005-0094-GX20 BLCD (256): 091 +001 BLCD (64k): 077 Figure 16 Check the version.
  • Page 15 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 7) The screen below is displayed after initialization and the phone turns off. Figure 20 8) Click the [OK] button. After the following screen, disconnect the cable. Figure 21 The setting is completed.
  • Page 16 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 2) Preparation • Connect PC and GSM tester with a GPIB cable. • Connect PC and MS with a Data cable. (Use a full charged battery or one close.) • Connect an antenna input/output cable of GSM tester to MS.
  • Page 17 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 4) RF adjustment 1. Press “Calibration”. 2. When initialization is complete, press “OK”. Figure 24 3. Turn on the phone and press “OK”. Figure 25 4. Make sure the phone is turned on and press “OK”. (Adjustments start.) Figure 26 5.
  • Page 18 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 5) RF performance check Press “Check”. 1. When initialization is complete, press “OK”. Figure 28 2. Turn on the phone, enter the PIN code and press “OK”. Figure 29 3. Make sure that the phone is in the idle mode and press “OK”.
  • Page 19 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 7. Make sure the terminal display is “In Call” and press “OK”. Figure 34 8. RF performance check is complete. Press “Save As…”and name the file to save the result. Press “OK” to exit.
  • Page 20 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Attachment 2 Band Send- Item to be inspected Chan- Whole inspection list by RF performance check. ing/ Recei Band Send- Item to be inspected Chan- ing/ Mod_spectrum +250 37CH PCL19 Recei...
  • Page 21 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Band Send- Item to be inspected Chan- Band Send- Item to be inspected Chan- ing/ ing/ Recei Recei Phase error (RMS) 699CH PCL0 Switch_Spectrum +1200 699CH PCL0 Phase error (RMS) 512CH...
  • Page 22 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Band Send- Item to be inspected Chan- Band Send- Item to be inspected Chan- ing/ ing/ Recei Recei Mod_spectrum –200 661CH PCL0 Switch_Spectrum –400 661CH PCL0 Mod_spectrum +200 661CH PCL0 Switch_Spectrum +400...
  • Page 23 This document describes the specification of the Flash-downloading tool (Upgrading Tool) used for the user service. 2) Purpose of this document The aim of this document is to provide a sufficient description of the GX20 Upgrading Tool for readers. 3) Scope This document covers the description of the Flash-downloading tool specification for the user service.
  • Page 24 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Note 1) If using “Communication Box Ver. 2G”, the only the phone connected to No.1 cable is controlled on your PC. Note2) The time displayed in this dialog indicates a margin of processing time taken for data to be downloaded to the phones that are connected to cable No.2 to No.10 of the “Communication Box Ver.
  • Page 25 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 2) Operational specification 1) Selecting a file. Press “Select File” button to open the dialog. Select a file you wish to download. You can only select the file with Motorola format.
  • Page 26 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 3) Using the Communication Box. Check the dialog box “Use Communication Box Ver. 2G” displayed on your PC if using “Communication Box Ver. 2G”. You can specify the wait time from 0 to 999 seconds since the access latency differs depending on the phone if using “Communication Box Ver.
  • Page 27 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 4) Starting the download. Press [Start Loading Flash] button after you finish selecting the file to download. Downloading operation starts. The message as below appears if no file is selected. •...
  • Page 28 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 6) Matters to be attended to the downloading operation. [If using a Data cable:] 1. Make sure to remove the AC charger from the Data cable. Otherwise it may cause the charging application to be activated and down- loading operation cannot be operated properly.
  • Page 29 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 2) Table of the Loading loader error messags (on the phone side) Display Message Description COMPLETE! Indicates that the downloading operation is completed. ERASE READY Appears while waiting for the erase operation to be ready.
  • Page 30 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 4) Installation / Un-installation 1) Installation Execute “setup.exe” and activate the setup wizard. Figure 44 Select a folder you wish to install to. Figure 45 2 – 24...
  • Page 31 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 The confirmation screen appears. Select [Next]. Figure 46 The Up Grading Tool is being installed. Figure 47 2 – 25...
  • Page 32 Figure 48 The icon of the Up Grading Tool as shown below is configured on your desktop. You can also activate this application selecting “The GX20 Up Ggrading Tool” from Start menu. Figure 49 The icon of theUp Grading Tool icon 2) Un-installation Execute “setup.exe”...
  • Page 33 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 The preloaded program is being un-installed. Figure 51 The un-installation is complete. Figure 52 2 – 27...
  • Page 34 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 3.3.6 Matters to be attended to the Installation /Uninstallation • If installing the Up Ggrading Tool to the PC that the tool has been already installed, uninstall the preloaded tool first then start installing the program again.
  • Page 35 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 6) Press “Reset”. The following confirmation message appears. Figure 56 7) Press “Yes” . Figure 57 8) When initialization is complete, the dialog box below appears. Press “OK” to turn off the phone.
  • Page 36 1. Set PWB and make connections as shown in Figures 62 and 63. Make sure connections are correct at the points shown in Figure 64. 2. Connect PC and GX20 with Data Cable. 3. Turn on the phone. 4. Start RF Test Tool.
  • Page 37 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Setting Pin Hook Setting Pin Hook Hook Setting Pin Figure 62 PWB installation Black Data Cable Figure 63 Connections 2 – 31...
  • Page 38 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Points Figure 64 Contact points Push Figure 65 Turning power on 2 – 32...
  • Page 39 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 3. Tests 3.1. BAND Select & Channel Select a band and a channel to test. Settings are applied to all tests. Input box Band selection Channel bar Figure 66 [Procedure] 1. Select a band. (GSM, DCS or PCS) 2.
  • Page 40 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL GX20 TX power Table (Target power during calibration, supply voltage: 3.7[V]) DCS/PCS TX Power [dBm] TX Power [dBm] 31.6 28.6 30.0 27.0 29.0 26.0 27.0 24.0 25.0 22.0 23.0 20.0 21.0 18.0...
  • Page 41 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 3.4. RSSI Measure The phone notifies you of input power value at the antenna connector. Measured power box Estimated Power Input box (Integer only) Measure button Figure 69 [Procedure] 1. Connect the phone and GSM tester (or Signal Generator) with RF cable.
  • Page 42 6. Send the [PWRDOWN] command to power off. 7. Hold down the "End/Power" key to display "****". 8. Press the "3" key to display "H/W CHECK *GX20*". Then the test mode is started. 9. Access the TEMP ADJ mode by pressing the “...
  • Page 43 6. Hold down the "End/Power" key to display "****". 7. Press the "3" key to display "H/W CHECK *GX20*" and then to access the test mode. 8. Press the "8" key to show the following pattern on the external display.
  • Page 44 2. Access the normal mode by holding down the “End/Power” key. 3. Send the [AT+XDIAG] command to receive the response [DIAGREADY]. 4. "Function Mode *GX20*"is shown on the display. 5. Cover the camera front to block off light completely. 6. Transmit the [WHC00840120000000] command.
  • Page 45 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 [4] Test points MAIN PWB-A (REAR SIDE) TP213 TP109 TP138 TP430 TP421 TP425 TP141 TP418 Figure 72 TEST POINT TP No. Signal name TP No. Signal name TP No. Signal name...
  • Page 46 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (FRONT SIDE) TP344 TP308 TP323 TP322 Figure 73 TEST POINT TP No. Signal name TP308 VEXT_CN TP344 DGND 2 – 40...
  • Page 47 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 KEY PWB-B (REAR SIDE) TP328 TP330 TP329 TP301 TP321 TP345 TP346 TP348 TP319 TP324 TP320 Figure 74 TEST POINT TP No. Signal name TP No. Signal name TP301 VSIM (2.85V) TP328...
  • Page 48 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [5] Troubleshooting 1. Power does not turn on. Connect a battery with voltage of more than 4.0 V. NOTE: If the cause is damage to 4-level memory (IC106), ensure to upload flash data before operation as initializing user area may prevent detecting the damaged data.
  • Page 49 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 (From page 2-42) More than 3.6 V output at BATT terminal (TPB336)? Battery terminal defective, adhesive foreign matter at contact battery (CN303) terminal, or bad soldering. Voltage of below 1.6 V applied to SENSE terminal (TPB331)? Battery or battery mounting defective.
  • Page 50 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 2. Incoming audio cannot be heard. Phone Signal output at the Back light FPC earpiece contact terminal? Built-in earpiece defective or defective connection between TP167 and TP168. Signal output at CN402 1 pin and 2 pin? Back light FPC or CN402 defective.
  • Page 51 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Hands free kit (Headset) When replacing the hands free kit, output available? Hands free kit defective. Signal output at JK301 4 pin? JK301 defective or defective connection. Signal output at IC101 5 pin?
  • Page 52 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Hands free car kit When replacing the hands free car kit, output available? Hands free car kit defective. Calling available in the hands free kit mode? Refer to "Hands free kit" in Troubleshooting "Incoming audio cannot be heard"...
  • Page 53 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 (From page 2-46) Voltage of approx. 1 V applied to IC102 54 pin? Voltage of approx. 1 V applied to IC102 64 pin? IC102 defective. Voltage of more than 2.4 V applied to Q101 3 pin?
  • Page 54 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Hands free kit (Headset) When replacing the hands free kit, output avilable? Hands free kit defective. Voltage of 1 to 1.9 V applied to JK301 3 pin? Voltage of 1 to 1.9 V applied to TP106? Parts of L105 to JK301 3 pin defective.
  • Page 55 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Hands free car kit When replacing the hands free car kit, output available? Hands free car kit defective. Calling available in the hands free kit mode? Refer to "Hands free kit" in Troubleshooting "Audio cannot be sent/recorded."...
  • Page 56 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 5. Vibrator does not operate. Vibrator terminals contacting the land? Vibrator deformed. Dirt or foreign matter detedted at vibrator terminals and the (Remove foreign matter or replace parts.) land? Check the vibrator during operation.
  • Page 57 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 7. Speaker does not operate. * When ring tones sound but only key touch tones do not, "Keypad Tones" are set to OFF. * When the ring tone volume is set to “Silent”, Voice Memo is not played back.
  • Page 58 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 8. Movie, Voice Memo cannot be played back. Speaker Key pad tones and incoming-call ring tones normally ? Refer to Troubleshooting, "Speaker does not operate." (see page 2-51). When normally starting playback on the playback screen, is IC104 or IC106 defective.
  • Page 59 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 9. Back light does not turn on. Do the keypad tones and ring tone sound from the speaker? Jumper (TPB333 to CN305 36, 37 pin) or Relay FPC_A, CN305, CN201 defective.
  • Page 60 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL (From page 2-53) Is the external display back light set to ON? ON Setting by the following menu. Settings → Phone settings → External display → Back light Does the back light turn on? Nondefective.
  • Page 61 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 10. "No Service" display and receiving/transmitting do not function. 10.1. "No Service" display and receiving/transmitting do not function in the EGSM band. [Checkpoints for GSM tester transmission] Fixed line: During input of –70 dBm.
  • Page 62 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 10.2. "No Service" display and receiving/transmitting do not function in the DCS/PCS band. [Checkpoints for GSM tester transmission] Fixed line: During input of –70 dBm. After replacing the main PWB unit with normal one, trans- IC104, IC102, CN201, CN202, or PWB defective.
  • Page 63 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 11. Main display does not function. Is main display to CN404 surely inserted? Connector insertion defective. Clean the connector CN404 contact point and insert the main Connector insertion part soiled. display again. Does it function? Does the display function after replacement? Main display defective.
  • Page 64 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 12. External display does not function. Does the main display function? Refer to Troubleshooting, “Power does not turn on.” (see page 2-42). Is the external display set to ON? ON Setting by the following menu: Settings →...
  • Page 65 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 13. Camera does not function. Does the camera flexible unit operate after replacement? Camera unit defective. Voltage of 2.5 V applied to TP211? Regulator IC208 or jumper (IC208 5 pin to TP211) defective.
  • Page 66 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL From the previous page C177, C413 and R410 defective. Voltage of –7 V applied to camera (CA1001) 31 pin? Are appearance and mounting of C177, C413 and R410 prop- erly given? Jumper (CN101 5 pin to TP413) and CN101 defective.
  • Page 67 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 14. Strobe light does not light up. Execute the AT command (STROBOR1, STROBOG1and STROBOB1) and then check which color does not light up among Red, Green and Blue. Red only Which color does not light up?
  • Page 68 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 15. SIM Card is not recognized. Can SIM card be recognized after replacement? SIM card defective or undesignated SIM card used. 2.8 V Output at Q208 5 pin? IC104 defective. 2.85 V Output at SIM power supply IC202 18 pin? IC202 or Q208 defective.
  • Page 69 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 16. IrDA Communications unavailable Set the specified distance and angle necessary for IrDA com- Check in the IRDA test mode. munications. 2.8 V output at Q207 2 pin? IC104 defective. Does IrDA power source TP216 output 2.8 V? Q207 defective.
  • Page 70 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [6] Specification for function test • Outline AT commands are used for the function test mode. To enter the general mode, send the command “AT+XDIAG”. Then the machine can accept all key test functions (see “All Key Test and Others” on page 2-76) and further commands from the computer.
  • Page 71 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 • Basic procedure (when using Hyper terminal) Flow chart Connect the phone to PC. Turn on the phone. Open Hyper terminal. Send “AT+XDIAG” with 115200 bps and proper “ASCII setting”. The phone is in the All key test mode. * Send further commands to check the phone.
  • Page 72 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL (Details) 1. Connect the phone to the computer via a data cable. 2. Turn on the phone. 3. Open Hyper terminal. (Start → Program → Accessory → Communication → Hyper terminal) 4.
  • Page 73 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 6. Adjust the port settings and click “OK”. Figure 77 7. From the file menu, select “Properties” and click the Settings tab. Figure 78 2 – 67...
  • Page 74 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 8. Click “ASCII setting” and check “Send line ends with line feeds” and “Echo typed characters locally”. Figure 79 9. Click “OK” for “ASCII setting” and “Properties” to exit. Figure 80...
  • Page 75 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 10. Send “AT+XDIAG” • You will see AATT++XXDDIIAAGG instead of AT+XDIAG as shown below by the Local echo mode, although you input AT+XDIAG. • After sending you will receive “OK”, and the machine should enter the All key test mode (see “All Key Test and Others” on page 2-76).
  • Page 76 Then enter AT+XDIAG without pressing any key. → Start up in the general function test mode. (3 sec. until startup) • Back light lights up in the standby mode. • After startup, “Function Mode * GX20 *” is displayed. Serial Signal Format for Basic Operation Test...
  • Page 77 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Incoming Serial Signal Outgoing Serial Signal Item Contents Test Method Command Response Temperature TMPADJ TMPADJ4nn Battery side -nn ºC. (Not cumula- Correcting difference between the correction tive subtraction) ambient temperature and the tem- TMPADJ3nn Battery side +nn ºC.
  • Page 78 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL * 1: The LED test is also available in the manual test mode F45. <Startup> 1. Fit a battery in the set to start the manual test mode. 2. Press the keys “4” → “5” → “Right Soft” to start the manual test mode F45 (LED Setting).
  • Page 79 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Description Contents Volume control. Turn up the volume by 1 level. “ ” During playback of ring tone: Ring tone is changed. During key touch tone output: Incoming audio volume is changed.
  • Page 80 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 3. Display Test Serial Signal Format for Main Display Test Incoming Serial Signal Outgoing Serial Signal Item Contents Test Method Command Response Checking LCDDISP LCDDISPn VCOM adjustment pattern. Checking for the main display.
  • Page 81 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 4. Audio Test Serial Signal Format for Audio Test Incoming Serial Signal Outgoing Serial Signal Item Contents Test Method Command Response Audio system PCMLP PCMLPnxx Mic to JackEar path check. Loop-back test for codec IC.
  • Page 82 4) Send the [PWRDOWN] command to power off. 5) Hold down the “End/Power” key to display “****”. 6) Press the “3” key to display “H/W CHECK *GX20*” and then to access the test mode. • After the test mode is started, the Data cable can be removed.
  • Page 83 RTC contents are displayed at the time the key “9” is pressed. Clock does not tick. KEY CHECK ∗ GX-20 ∗ ROM VERSION : ∗∗∗ GX20 Diag Version ∗∗∗ CVS Ver. A∗∗_∗∗∗_∗∗∗∗_GX20 BLCD (256) : 089+004 BLCD (64K) : 075 2003/**/** **: **: ** Press all keys except the key “0”...
  • Page 84 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Contents Shifting to the mode for temperature correction. “ ” TEMP ADJ 1. CAM TEMP 2. BAT TEMP 0. EXIT “1” (Selecting the camera side) or “2” (Selecting the battery side) “0” Exit TEMP ADJ (BAT) Temp.
  • Page 85 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL OZ/IQ/YO/Calc GX20 Service Manual TQGX20 Market CHAPTER 3. DISASSEMBLY AND REASSEMBLY [1] Servicing Concerns • SOLDERING SPECIFICATION Soldering iron must be set to 350° C for 5 seconds. 1. General • Diagram for Service Label Position 1.
  • Page 86 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Cushion, Battery Sheet, Shade Standard Standard position position Standard position Holder, Mg [Sheet, Shade] Back Cabinet (key) [Cushion, Battery] Standard position Standard Sheet, position Sensitivity decrease prevention Standard position Standard Tape, Mg Holder...
  • Page 87 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Standard Spacer, position Main PWB-A Standard Key PWB position (Rear Side) Cushion, Main Connector Standard position Electrostatic Sheet, Side keys Standard position Spacer, Standard External Display position Standard position [Cushion, Main Connector/Spacer, External Display FPC]...
  • Page 88 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Application range Cushion, Reinforcement Back Cabinet (Display) [Cushion, Reinforcement] Standard Driver Sheet position Application range Cushion, Driver Standard position Sheet, Driver Front Cabinet (Display) [Cushion, Driver/Sheet, Driver] 3 – 4...
  • Page 89 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [2] Disassembly and reassembly • To reassemble, follow the reverse procedure. (A1) x 1 STEP REMOVAL PROCEDURE FIGURE Back Cabinet 1.Battery Cover..(A1)x1 (Key) Ass’y 2.Li-Ion Battery..(A2)x1 (A2) x 1 3.Screw Cover..
  • Page 90 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL STEP REMOVAL PROCEDURE FIGURE Back Cabinet (Display) Back Cabinet 1.Screw Cover..(C1)x4 Ass'y (C3) x 7 (Display) Ass’y 2.Screw....(C2)x4 3.Hook..... (C3)x11 Main PWB-A 1.Solder....(D1)x3 2.Sheet....(D2)x2 3.Socket....(D3)x6 4.Hook.....
  • Page 91 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL - MEMO - 3 – 7...
  • Page 92 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL OZ/IQ/YO/Calc GX20 Service Manual TQGX20 Market CHAPTER 4. DIAGRAMS [1] Block diagram [Main] RF I/F VANA CLKIN IRXP ITXP RAMPDAC GPO_18(SYNTHEN) CLKON,GPO_1(TXON) VCORE (13MHz) IRXN ITXN AFCDAC GPO_20(SYNTHDATA) GPO_2(BS2),GPO_9(RFON) VMEM QRXP...
  • Page 93 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL GPIO_8(Hardware revison monitor[0]) GPIO_16(Hardware revison monitor[1]) CA1001 GPIO_17(Hardware revison monitor[2]) CAMERA UNIT When JTAGEN=H, VSIM automaticaly VCORE GPIO_18 nWE,nRD,nDISPLAYCS2, VMEM X102 GPIO_19 sensor ADD[19:17],ADD[2:1],D[15:0] VINT 32kHz GPIO_20 IP part VRTC CRYSTAL...
  • Page 94 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [RF] +B(VRF) IC991 NL27WZ08 IC992 TC7W00FK IC993 NL27WZ08 LOGIC RAMPDAC SYNTHEN SERIAL DATA IC901 SYNTHDATA INTERFACE HD155148TF SYNTHCLK ITXN ITXP I&Q PHASE DETECTOR QTXN QTXP TCXOOUT 28,30,31,32,41,46 +B(VTCXO) 90DEG TCX951 SHIFT1/2...
  • Page 95 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC881 +B(VTXVCO) 4,9,10 HD155173 AUTO 5,6,7 POWER 11,14 CONTROL 1,2,15,16 TxVCO R811 R816 EGSM 880.2MHz - 914.8MHz DCS 1710.2MHz - 1784.8MHz PCS 1850.2MHz - 1909.8MHz +B(VBAT) +B(VTXVCO) DIRECTIONAL COUPLER FL816 LOOP...
  • Page 96 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL - MEMO - 4 – 5...
  • Page 97 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL OZ/IQ/YO/Calc GX20 Service Manual TQGX20 Market CHAPTER 5. SCHEMATIC DIAGRAM AND WIRING SIDE OF P.W.BOARD [1] Notes on schematic diagram • The indicated voltage in each section is the one measured by Digi- tal Multimeter between such a section and the chassis with no sig- •...
  • Page 98 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [3] Waveforms of circuit RF UNIT PLL_IC SERIAL COMMUNICATION SYNTHDATA TCXOEN (STAND-BY) (STAND-BY) IC901 39Pin IC304 1Pin RFON_B (STAND-BY) R351 (Q304 5Pin) SYNTHEN (STAND-BY) IC901 35Pin TXON_B (Talking) R352 (Q304 4Pin)
  • Page 99 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL ITXN IRXN (Talking) (Talking) C923 IC901 27Pin (IC901 20Pin) ITXP IRXP (Talking) (Talking) C923 IC901 26Pin (IC901 21Pin) QRXN BS0(GSM) (Talking) (Talking) IC901 24Pin IC993 1Pin QRXP BS1(GSM) (Talking) (Talking) IC901 25Pin IC993 2Pin 5 –...
  • Page 100 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL CLKIN BS2(GSM) (Stand-by) (Talking) C148 IC992 1Pin (IC104 142Pin) CLKOUT BS0(DCS) (Stand-by) (Talking) Jumper IC993 1Pin (IC104 84Pin –IC102 46Pin) OSCIN BS1(DCS) (32 kHz) (Talking) (Stand-by) IC993 2Pin R147 (IC104 49Pin)
  • Page 101 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL VSYNC BS2 (PCS) (Stand-by) (Talking) TP426 IC992 1Pin SUBFLM (Stand-by) L445 7Pin In this case, the external display is in 256-color mode with the handset closed. BS0 (PCS) (Talking) IC993 1Pin...
  • Page 102 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [4] Schematic diagram/wiring side of P.W.Board MAIN PWB-A (1/3) MAIN PWB-A(1/3) C448 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 1 2 3 4...
  • Page 103 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL LCD100 MAIN DISPLAY TP430 C447 1 2 3 4 TP426 C472 TP425 10P(CH) C469 TP424 10P(CH) TP422 TP421 TP420 1 2 3 4 C474 10P(CH) C471 10P(CH) MP4_PLLCK MP4_P0 GTDIO_B MP4 RESET_B...
  • Page 104 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (1/3) C416 /LCD_RESET TP415 FS402 Fuse FS403 0.63A Fuse FS401 0.63A Fuse LED401 LED402 NSCW335 NSCW335T R455 470K NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1. Figure 3 SCHEMATIC DIAGRAM (3/24)
  • Page 105 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL R413 100K IC402 IX3053AF C415 POWER MANAGEMENT R410 1.2K TP413 C413 5-15 (11-C) CAMN GND3 CAMP GND2 GND1 5-15 (12-C) CAPN2 C411 TEST CAPP2 CUR1 CAPN1 C409 CUR2 CAPP1 R407 TP412...
  • Page 106 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (2/3) MAIN PWB-A(2/3) RECEPTION SIGNAL 5-18 (3-D) TRANSMISSION SIGNAL VIB_CNT SPEAKER SIGNAL TP110 SP1-1 5-18 (6-B) SP2-1 TP111 SIMIO SIMCLK 5-18 (4-G) SIMRST KEYPADROW[0-4],KEYPADCOL[0-4] 5-18 (5-E) 3.0V 5-12 (2-F)
  • Page 107 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 5-18 (4-G) R124 C144 VBAT_AP VINT 0.047 R182 C141 VIB_CNT VBAT_AP 5-8 (6-D) C142 R172 C143 SPOUT1 VREF SPOUT2 C146 IC103 EXT2 0.001 DATA[7] R173 PLLC YMU759B DATA[6] R128 IFSEL SOUND 3.3K...
  • Page 108 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (2/3) 5-19 (10-C) 5-18 (4-G) 2.45V VANA SYNTHDATA VANA_AD6521 SYNTHEN 5-18 (5-H) SYNTHCLK 5-18 (3-C) ITXP ITXN 5-18 (4-D) QTXP 5-18 (3-C) QTXN IRXP IRXN 5-18 (4-C) Q101 R106...
  • Page 109 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL VINT GPIO_21 [TDO] MC_CLK MC_CMD MC_DAT[0] MC_DAT[1] MC_DAT[2] MC_DAT[3] GPIO_22 [Not use] DPLUS DMINUS GPO_00 [RXON] 5-19 (7-E) TXON 2.8V 1.8V GPO_01 [TXON] VMEM VCORE GPO_02 [BS2] GPO_03 [ADC_MTC] C133 C131...
  • Page 110 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (2/3) 5-18 (3-D) FLIP_SW 5-18 (12-F) (11-F) (3-G) KEY_BL_ON LEDR LEDG 5-18 IR_O ADD[1] DATA[0-15] ADD[19] 5-18 ADD[18] (4-G) ADD[17] ADD[1] 1.8V 2.85V 3.0V 2.8V 3.0V 3.0V ADD[2] VRTC...
  • Page 111 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 5-19 (10-D) 3.0V VINT UN101 INFRARED PORT SGND LEDA IR_SD 5-18 (6-D) 5-18 (6-D) IR_ON 5-19 (10-D) 5-19 (9-F) 5-9 (7-B) 5-9 (7-C) 2.5V 3.0V 3.1V +13V VCCD VINT VCAM C184...
  • Page 112 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (2/3) TP128 nAUXCS1 [Not use] TP151 [LCD Controller /CS] GPIO_42 GPIO_43 [Camera /CS] GPIO_44 [Not use] GPIO_45 [Not use] TP130 GPIO_46 [Sound_IC /CS] R171 nHWR [/UBS] R178 nLWR [/LBS]...
  • Page 113 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL to LCD Curcuit SUB_BL_ON /LCD_CS 5-8 (4-F) 5-8 (4-F) DATA[0-15] 5-8 (4-F) DATA[0-15] 3.0VV 5-8 (5-F) VINT 5-8 (4-F) /LCD_WAIT BUFOFF 5-8 (4-F) LCD_RST 5-8 (3-F) 5-14 5-18 (6-F) (6-B) TP176 3.0V...
  • Page 114 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC201 MAIN PWB-A(3/3) 5-17 (8-C) XC6209B302MR 3.0V VBACK RECEPTION SIGNAL HIGH SPEED LDO VBAT_BB TP203 REGULATOR TRANSMISSION SIGNAL TP202 Vout SPEAKER SIGNAL IC204 RELAY FPC_A BACK_BATT R3111Q251C 5-8 (6-D) PWB-C VOLTAGE...
  • Page 115 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL VANA IC203 P203 Q204 2.46V RQ5RW18B 2SA1989 SR 1.8V REGULATOR Q203 RT1N144 U ADC_MTC 5-12 (2-G) 1.8V BATT_SENSE 2.44V VOUT 5-12 (1-F) TP205 VBAT_BB C210 VBAT_BB 5-13 (9-G) PWRON C220 PWRON...
  • Page 116 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (FRONT SIDE) IC210 L103 C182 C157 C159 L104 C183 C448 TP139 C158 R178 C474 IC405 TP123 TP128 TP129 TP148 C462 TP147 TP140 TP142 TP149 IC106 TP150 TP152 IC104 IC403...
  • Page 117 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL MAIN PWB-A (REAR SIDE) 5-34 (5-F) FROM LCD100 TP168 TP167 TP430 TP425 TP109 TP420 TP418 TP426 TP213 TP421 TP422 TP141 TP138 TP424 CN404 FROM R193 BACK LIGHT FPC C470 C457 ASS'Y PWB-F...
  • Page 118 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (1/2) FLEXIBLE PWB, SIDE SWITCH PWB-I KEY PWB-B(1/2) RECEPTION SIGNAL SIDE-UP SIDE-DOWN TRANSMISSION SIGNAL SPEAKER SIGNAL V318 D310 V317 RSB6.8S 100P 100P CENTRE RIGHT RIGHT SO "VODAFONE LIVE" SEND...
  • Page 119 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL TP451 and TP452 are patterns for Vibrator. VVIB MO100 VIBRATOR DGND SP100 5-18 (1-C) SPEAKER AGND KEYPADCOL0 KEYPADCOL1 KEYPADCOL2 KEYPADCOL3 KEYPADCOL4 GOAST TP305 On the FPC On the FPC KEYPADROW0 CENTRE...
  • Page 120 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (1/2) Power(-) V301 L305 R310 100P FERRITE BEADS FLashload_ON "High" Genie_CHG L306 R312 FERRITE BEADS L307 R313 Debug_Tx FERRITE BEADS L308 R314 FERRITE BEADS D307 R315 L309 "Low" ADPDET RSB6.8S...
  • Page 121 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL GENIE_CHG 2.99V TP309 D301 HN2S01FU TP313 TP311 ADPDET D302 CONT2 HN2S01FU CONT1 3.0V VINT TP314 C316 TP315 Q301 UM6K1 IC301 TC7WH04FK LOGIC 0.01V 0.93V Q302 IC308 UM6K1 TC7SZ04A LOGIC TP322 TP323...
  • Page 122 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (1/2) IC302 VBAT NJM2871F03 VBAT 3.0V REGULATOR CONT VOUT C340 Q303 2SC4617 R C341 D304 TP346 1SS388 R325 1.2K TP345 R327 VBAT Vout ON/OFF IC306 D309 TK71635S CUS01 HIGH SPEED LDO...
  • Page 123 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL RERAY FPC_A PWB-C 5-18 (2-E) CN405 IC307 C308 LM20BIM7 VINT TEMPERATURE 2.715V SENSOR R368 IC305 EW6671 HALL 5-22 (4-G) 2.715V VEXT_CN VBAT_AP VBAT_S CN305 DGND CONT1 CONT1 DGND IRXN IRXN GATEDR...
  • Page 124 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (1/2) 2.9V TP319 2.9V 5-30 (2-C) Q309 VTXVCO VTXVCO 2SA1955 A IC304 TK11129CSIL 2.9V REGULATOR TCXOEN R351 1.2K RFON 2.88V R352 1.2K TXON 2.87V Q304 EMG9 TP324 L314 C326...
  • Page 125 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL TXON TXON ADIN_B VEXT_ON ADIN_B GENIE_CHG GENIE_CHG POWONKEY POWONKEY 2-C) POWONKEY 5-24 5-26 5-24 (3-F) (2-F) (2-C) VINT VSIM VBAT_BB CHGIN CN306 VBAT_BB KEYPADCOL[0] KEYPADCOL0 VBAT_BB KEYPADCOL[1] KEYPADROW[2] KEYPADCOL1 KEYPADROW2 KEYPADCOL[2]...
  • Page 126 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B(2/2) TRANSMISSION SIGNAL RECEPTION SIGNAL BS1 BS2 HIGH IC992 TC7W00FK HIGH HIGH LOGIC HIGH LOW LOW HIGH HIGH HIGH HIGH HIGH 5-29 (1-D) IC993 NL27WZ08 5-23 (11-G) BATT LOGIC VTXVCO...
  • Page 127 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC991 NL27WZ08 LOGIC IC881 C885 Pin 8 0.01 HIGH C836 1 2 3 4 100P(CH) C834 C833 100P R885 C882 C860 (CH) (CH) R853 100P(CH) 22P(CH) DCS/PCS TX DCS/PCS TX IC831...
  • Page 128 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL KEY PWB-B (FRONT SIDE) LEFT RIGHT SOFT SOFT CENTRE V317 V318 R345 R346 LED311 LED312 TP344 R344 R335 END/ SEND POWER "VODAFONE LED310 LED301 LIVE!" TP308 D308 Q303 TP323 FL303 C326...
  • Page 129 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 5-34 (4-D) (103-6) KEY PWB-B (REAR SIDE) FROM RELAY FPC_B PWB-D FROM RELAY AERIAL FPC_C PWB-E 5-34 (6-C) 5-34 (2-D) TP348 FROM RELAY FPC_A SOLDER SOLDER PWB-C TP305 TP307 CN405 TP321...
  • Page 130 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL RELAY FPC_B RELAY FPC_A RELAY FPC_C PWB-C PWB-D PWB-E TO MAIN PWB-A (FRONT SIDE) TO MAIN PWB-A (FRONT SIDE) CN201 5-20 (4-G) CN202 5-20 (3-G) 5-20 (4-G) TO MAIN PWB-A (FRONT SIDE)
  • Page 131 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Conditions: SIM card inserted, power on, in stand-by mode (opened) Measuring instrument: Digital multimeter : Unmeasurable IC101 IC203 IC210 IC107 IC307 PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO.
  • Page 132 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC831 IC901 IC991 PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE 0.19V 2.94V 3.89V 2.94V 3.89V 2.95V 2.94V 2.94V 0.14V IC992 0.14V IC881 PIN NO. VOLTAGE PIN NO. VOLTAGE 2.94V 0.19V...
  • Page 133 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL OZ/IQ/YO/Calc GX20 Service Manual TQGX20 Market CHAPTER 6. OTHERS [1] Function table of IC IC101 VHINJM2149R-1+ (NJM2149R): SPEAKER AMP. Pin No. Terminal name Input/Output Description of terminal Input Chip disable control terminal...
  • Page 134 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC102 (AD6521ACA): ANALOG BASEBAND Pin No. Terminal name Input/Output Description of terminal DVDD1 – Digital core power supply (1.6V AVDD1/2) DGND1 – Digital ground IDACREF Output Current DAC bias resistor connection, rset...
  • Page 135 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal VOUTAUXP Output Differential voiceband auxiliary output (Jack Earpiece audio output) VINNORN Input Differential voiceband normal input In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
  • Page 136 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC103 VHIYMU759B+1FL (YMU759B): SOUND Pin No. Terminal name Input/Output Description of terminal CLKI Input Clock input terminal (2 – 20 MHz) EXT1 Output External control terminal 1 /IRQ Output Interrupt output terminal...
  • Page 137 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC104 (AD6529): DIGITAL BASEBAND Pin No. Terminal name Input/Output Description of terminal ASDO Output Audio serial port data output BSDI Input Baseband serial port data input BSOFS Input Baseband serial port output framing signal...
  • Page 138 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal MC_DAT[1] Input/Output MC_DAT [1] – Ground VEXT – External device power supply 2.4V to 3.3V KEYPADCOL[0] Input/Output KEYPADCOL [0] VEXT – External device power supply 2.4V to 3.3V...
  • Page 139 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal VMEM – Memory power supply 2.7V to 3.3V memory support – Ground – Core power supply voltage 1.7V to 1.9V USC[6] Input USC pin (CONT2) –...
  • Page 140: Table Of Contents

    All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal nAUXCS1 Output Sound IC chip select GPIO_43 Input/Output Display 2 chip select VDDUSB – USB power supply 2.8V to 3.3V GPIO_23 Input/Output SIM Reset...
  • Page 141: Pin No

    All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC106 (LRS1B24): 4-LEVEL STACK MEMORY Pin No. Terminal name Input/Output Description of terminal – Not used – Not used Input Address input (Flash, Smartcombo RAM) Input Address input (common) Input Address input (common)
  • Page 142 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) SC-/CE1 Input Chip enable input (Smartcombo RAM) –...
  • Page 143 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC201 VHIXC620930-1L (XC6209B302MR): HIGH SPEED LDO REGULATOR Pin No. Terminal name Input/Output Description of terminal Input Input – Ground Input ON/OFF Control – Not used VOUT Output Output In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
  • Page 144: Terminal Name Input/Output

    All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC203 VHIRQ5RW18B-1L (RQ5RW18B): 1.8 V REGULATOR Pin No. Terminal name Input/Output Description of terminal – Ground – Power supply VOUT Output Output Input Chip enable VOUT VREF CURRENT LIMIT IC204 VHIR3111Q25-1L (R3111Q251C): VOLTAGE DETECTOR Pin No.
  • Page 145: Input/Output

    All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC206 VHITK11131C-1R (TK11131C): REGULATOR IC209 VHITK11130C-1R (TK11130C): REGULATOR Pin No. Terminal name Input/Output Description of terminal CONT Input Control (IC209: VCONT) – Ground – Capacitor VOUT Output Output Input Input VOUT Over Heat &...
  • Page 146: Input/Output

    All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC210 VHIR3112Q26-1L (R3112Q261A): VOLTAGE DETECTOR Pin No. Terminal name Input/Output Description of terminal – Power supply – Ground Input External condenser connection terminal for delay Output Output terminal (L: when output is detected, H: when output is cancelled)
  • Page 147 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC303, IC304 VHITK11129C-1R (TK11129CSIL): 2.9 V REGULATOR Pin No. Terminal name Input/Output Description of terminal CONT Input Control – Ground – Capacitor VOUT Output Output Input Input VOUT Control Constant Over Heat &...
  • Page 148 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC306 VHITK71635S-1R (TK71635S): HIGH SPEED LDO REGULATOR Pin No. Terminal name Input/Output Description of terminal – Power supply – Ground ON/OFF Input ON/OFFcontrol Input VREF (NP) VOUT Output Output 5 VOUT...
  • Page 149 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC402 (IX3053AF): POWER MANAGEMENT Pin No. Terminal name Input/Output Description of terminal – Dummy terminal (connected with T2 internally.) LEDG Output G LED drive output terminal (Constant current drive) GND1 –...
  • Page 150 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL LEDG GND1 VBAT1 LSO11 LSO12 WVOUT TEST LEDR LEDB TRSW LSO21 LSO22 CAPP1 CAPN1 SENSP SENSN CPIN CAPP2 VPLUS2 CAPN2 GND3 STRB VPLUS12 CAMP DATA IREF VREF LEDCTL CUR2 CUR1 FLED...
  • Page 151 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC403 (LR38863): DISPLAY CONTROLLER Pin No. Terminal name Input/Output Description of terminal DUMMY4 – Dummy 4 VDDPLL – PLL Power supply 1.8 V (1.6 V~ 2.0 V) PLLGND – PLL Ground...
  • Page 152 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal SUBDB0 Input/Output Data bus for External display SUBDB2 Input/Output Data bus for External display HSD5 Input/Output Data bus for high-speed serial transfer Input/Output...
  • Page 153 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal DB14 Input/Output Data bus DB15 Input/Output Data bus WAIT_B Output External wait signal (“Low” is active) SUBFLMIN Input Driver FLM signal input for External display...
  • Page 154 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL RESET_B Reset SE_LD2/PORT5 FULL Some MHz SE_LD3/PORT6 Halt MasterClock (MCLK) TEST ····· VRAM/HOST/HS/BS/ to 68 MHz Scan Some MHz to 33 MHz VDIF/VSPetc Ctrl PWM0/PORT3 LCDTimingClock (TCLK) PLLDIV[2:0] ····· TG/Pallet/LCD IF...
  • Page 155 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC404 VHILT1937++-1R (LT1937): DC - DC Pin No. Terminal name Input/Output Description of terminal Output LED voltage output – Ground Input LED ground SHDN# Input Chip enable – Ground Input Input...
  • Page 156 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC831 VHIPF08123B-1L (PF08123B): RF POWER AMP. Pin No. Terminal name Input/Output Description of terminal Pin GSM Input Input power from TXVCO (GSM) Vapc Input Power control voltage from APCIC Vdd1 –...
  • Page 157 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC901 VHIHD155148-1L (HD155148TF): RF Pin No. Terminal name Input/Output Description of terminal GNDLNA – Ground for LNA bias VCCLNA Input VCC for LNA transistor and LNA bias GNDDUM,GNDPCS – Ground for emitter of LNA transistor (PCS)
  • Page 158 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL IC991, IC993 VHINL27WZ08-1R (NL27WZ08): LOGIC Pin No. Terminal name Input/Output Description of terminal Input Input 1 Input Input 1 Output Output 2 – Ground Input Input 2 Input Input 2 Output Output 1 –...
  • Page 159 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL [2] Function table of Camera CA1001 (DKENDW025AFSI): CAMERA UNIT Pin No. Terminal name Input/Output Description of terminal – Digital ground VDD1 – Power supply input (2.5 V/DSP core) Input Address bus 19...
  • Page 160 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL PARTS GUIDE DIGITAL MOBILE PHONE GX20 MODEL (INTERNAL MODEL NAME: TQ-GX20E/G/R/T/S/H/EP/PP/W/B/D/A/Z/Q/L/F/C) E : For U.K. G : For Germany R : For Ireland T : For Italy S : For Spain H : For Netherlands EP : For U.K.
  • Page 161 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 PRICE PRICE PART CODE DESCRIPTION PARTS CODE DESCRIPTION RANK RANK INTEGRATED CIRCUITS D310 VHERSB6R8S+-1L AC Zener,6.8V,RSB6.8S D401 VHDRB520S30-1- AB Schottky,RB520S30 D402 VHDRB521S30-1- AB Silicon,RB521S30 IC101 VHINJM2149R-1+ AF Speaker Amp.,NJM2149R D403 VHERD22SL++-1L...
  • Page 162 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL PRICE PRICE PART CODE DESCRIPTION PARTS CODE DESCRIPTION RANK RANK AB 0.01 µF,16V ARRAY PARTS C226 VCKYCZ1CB103KT AD 4.7 µF,6.3V C227 RC-KZ1308AFZZT AA 0.22 µF,10V C228 VCKYCY1AB224KT L445~451 RCILZ0390AFZZN AC Array,120 ohms AC 2.2 µF,6.3V...
  • Page 163 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 PRICE PRICE DESCRIPTION DESCRIPTION PART CODE PARTS CODE RANK RANK C821 VCCCCZ1EH1R5CT AB 1.5 pF (CH),25V R197 VRS-CZ1JB124JT AB 120 kohms,1/16W C824 VCCCCZ1EH1R0CT AA 1 pF (CH),25V R199 VRS-CZ1JB333JT AB 33 kohms,1/16W...
  • Page 164 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL PRICE PRICE PART CODE DESCRIPTION PARTS CODE DESCRIPTION RANK RANK CN301 QSOCZ9171AFZZL AH SIM Card Connector DKENDW025AFS3 CV Board Unit [A] CN302 QSOCN1801AFZZL AM External Connector DKENDW025AFS4 CV Board Unit [EP]...
  • Page 165 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 PRICE DESCRIPTION PART CODE RANK ACCESSORIES/PACKING PARTS GFTAB1404AFSA AH Cover,Battery RADPT6214AF01 AC Charger [A] [Z] RADPT7203AF01 AC Charger [B] [D] [G] [H] [PP] [S] [T] [W] [Q] [F] [C] RADPT8201AF01 AC Charger [E] [EP] [R] [L]...
  • Page 166 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL 107x2 602x2 602x2 102-5 102-1 103-3 102-2 102-3 103-6 104-27 104-18x2 103-4 (LCD001) 104-37 104-16 103-1 104-43x2 104-14 104-36 104-38 103-2 104-40 103-8 [F], [C] and Except for [F], [C] 104-41...
  • Page 167 All manuals and user guides at all-guides.com CONFIDENTIAL GX20 Packing method 1. GFTAB1404AFSA Cover,Battery 12. TGANZ1111AFZZ Guarantee [PP] 2. RADPT6214AF01 AC Charger [A] [Z] 12. TGANZ1112AFZZ Guarantee [W] 2. RADPT7203AF01 AC Charger [B] [D] [G] [H] [PP] [S] [T] [W] [Q] 12.
  • Page 168 All manuals and user guides at all-guides.com GX20 CONFIDENTIAL © COPYRIGHT 2003 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents