Electrical Specifications; Standard Specifications; Supplied Accessories - Kenwood TK-2180 Modification Information

2 CONNECT OPTIONAL DEVICES

2.5.5 Electrical Specifications

!
Terminal Specifications
Table 2-16 Terminal Specifications
PCB interconnection connector: E40-6378-x5 (14-pin
Connector)
Panel Side
Description
Pin Signal
Number Name
Front Panel
1 SPI
Speaker Input
2 GND Ground
3 8C 8 V Power Supply
Power Entry After
4 SB
Power-on
5 GND Ground
Power Switch
6 PSW Control Signal
Input
7 MIC Mic Signal Output
8 ME Mic Ground
Panel Separate
9 PSENS
Output
Serial Data
10 TXD
Output
Serial Data
11 RXD
Output
12 GND Ground
13 SHIFT Beat Shift Output
Sub -com Reset
14 RST2
Input

2.5.6 Standard Specifications

Table 2-17 Standard Specifications
" MIL STANDARD
Meets the following specifications to comply with the
specifications. The KMC-35/ 36 must be used with
the specifications.
MIL810-C MIL810-D
500.2/
500.1/
Low
Procedure
Pressure Procedure I
I, II
501.2/
501.1/
High
Procedure Procedure
Temp.
I, II
I, II
502.2/
Low 502.1/
Procedure
Temp. I
Procedure
I, II
18
Side Transceiver
Pin Signal
Number Name
14 SPI
13 GND
12 8C
11 SB
10 GND
9 PSW
8 MIC
7 ME
6 PSENS
5 TXD
4 RXD
3 GND
2 SHIFT
1 RST2
MIL-810E MIL-810F
500.3/ 500.4/
Procedure Procedure
I, II I, II
501.3/ 501.4/
Procedure Procedure
I, II I, II
502.3/ 502.4/
Procedure Procedure
I, II I, II
Modification Information
MIL810-C MIL810-D
503.1/ 503.2/
Temp.
Shock Procedure I Procedure
Solar 505.1/ 505.2/
I
Radiation Procedure Procedure
506.1/ 506.2/
Rain Procedure Procedure
I, II I, II
507.1/ 507.2/
Procedure Procedure
Humidity
I, II II, III
509.1/ 509.2/
Salt Fog
Procedure I Procedure
510.1/ 510.2/
Dust
Procedure I Procedure
514.2/
514.3/
Procedure
Vibration
Procedure
VIII, X
516.2/ 516.3/
Shock Procedure Procedure
I, II, III, V I, IV, V
" IEC 529 (IP Code) IP-XX
Meets the following specifications to comply with the
specifications. The KMC-35/ 36 must be used as an
optional microphone.
Element Code Letters
IP
Numbers or
(International
Letters
Protection)
*1
If IP-x5 is applicable to the head unit only, IP-x4 is applicable to
the transceiver body.
If the head unit is mounted to the transceiver body, IP4X is
applicable to the transceiver.
" Display
No remarks.

2.5.7 Supplied Accessories

Table 2-18 Supplied Accessories
No. Name Part Number Qty.
1 Screw Set N99-2040-x5
2 Bracket J29-0698-x3
3 Dressed Screw N08-0550-x4
4 Interface Cable E30-7514-x5
5 Rubber Cap F07-1884-x3
MIL-810E MIL-810F
503.4/
503.3/
Procedure
I Procedure I
I, II
505.3/ 505.4/
I I
Procedure Procedure
506.3/ 506.4/
Procedure Procedure
I, II I, III
507.3/
Procedure
507.4
II, III
509.3/
509.4
I Procedure I
510.4/
510.3/
Procedure
I I
Procedure
I, III
514.4/ 514.5/
I I
Procedure Procedure
516.4/ 516.5/
Procedure Procedure
I, IV, V I, IV, V
First Code Second Code
4 (Splashing)
5 (Dust-
*1
protection)
5 (Jetting)
Remarks
1 -
1 -
2 -
1 Length: 700 cm
2 -
Version: 1.13 USA
I
I