Briv ® - Imperial - Stanley Genesis 07537 Original Instructions Manual
Hydro-pneumatic power tool
Hide thumbs
Also See for Genesis 07537:
- Instruction and service manual (292 pages) ,
- Instruction and service manual (364 pages) ,
- Instruction and service manual (100 pages)
Table of Contents
Advertisement
N o s e A s s e mb l i e s
To find the correct part number of a mandrel for a particular application, read the instructions below after you have gathered the following information as per
example alongside. Answers for the example are shown in
FASTENER NAME
FASTENER SIZE
DATASHEET
APPLICATION HOLE SIZE
CLEARANCE BEHIND APPLICATION
'REF.Nş' FROM NOSE JAW SELECTION TABLE
•
Subtract the minimum hole size recommended (AS REC.) in the fastener datasheet from the actual application hole size.
•
Turn to the page with the 'Mandrel Selection' table for your fastener, selecting either the imperial or the metric dimensions table (pages 16-20).
-example: page 16.
•
Staring with the 'Standard Mandrel - Green' section, find your fastener size in the left-hand column.
•
If you selected a nose jaw which place you fastener, you should now be able to find a line within your fastener section with the same 'Ref No.' as that
from the 'Nose Jaw Selection' table.
number. This line continues into the second half of the table for the '2nd' and '3rd' oversize mandrels.
•
Scan along the line to the 'hole size' columns and select which ever is the nearest or equal to the figure calculated in step one. You may now read the
mandrel part number next to the 'hole size'.
•
For Chobert
®
and Grovit
®
only, most mandrels are also available in a 'short reach' version (see illustration on page 19). Short reach mandrels are used
to minimise the possibility of the mandrel head contacting an obstruction. This would result in the underside of the fastener head not seating properly on
the application surface, causing a lack on clench in the joint.
•
Whichever size mandrel you settle on, you will also need to check the 'P' figure against that mandrel is adequate. 'P' is the clearance required for the
mandrel head at the back of the application IN ADDITION to the length of the fastener protruding through the application, as shown in the illustration on
page 19.
•
You may now read the corresponding mandrel follower spring part number in the right-hand column of the table.
In all cases, satisfactory clenching of the joint should be assessed particularly if the size of the hole in your application is very close to the next oversize hole
condition, when it will be safe to select the greater size of mandrel to obtain a higher clench. REMEMBER that this will increase the broach load and reduce
the mandrel life.
®
Bri v
- Impe ria l
For mandrel or mandrel follower spring selection, follow instructions above.
REF.
HOLE
FASTENER
Nº
SIZE
3/32" BRIV ®
13
AS REC.
Brass only
14
AS REC.
1/8" BRIV ® Al.
15
AS REC.
Alloy, Brass, Steel
16
AS REC.
5/32" BRIV ® Al.
17
AS REC.
Alloy, Brass, Steel
18
AS REC.
5/32" BRIV ®
19
AS REC.
St.Steel only
20
AS REC.
3/16" BRIV ® Al.
21
AS REC.
Alloy, Brass, Steel
22
AS REC.
3/16" BRIV ®
23
AS REC.
St.Steel only
24
AS REC.
6mm BRIV ® Al.
25
AS REC
Alloy, Steel
26
AS REC
REF.
HOLE
FASTENER
Nº
SIZE
3/32" BRIV ®
13
+.008
Brass only
14
+.008
1/8" BRIV ® Al.
15
+.010
Alloy, Brass, Steel
16
+.010
5/32" BRIV ® Al.
17
+.010
Alloy, Brass, Steel
18
+.010
5/32" BRIV ®
19
-
St.Steel only
20
-
3/16" BRIV ® Al.
21
+.010
Alloy, Brass, Steel
22
+.010
3/16" BRIV ®
23
-
St.Steel only
24
-
6mm BRIV ® Al.
25
+.010
Alloy, Steel
26
+.010
18
grey italic.
-example: 5.
This is your line 'Ref. No.' in which you will find both your mandrel and mandrel follower spring part
-example: 07150-06104
STANDARD MANDREL - GREEN
HEAD Ø
MANDREL PART Nº
.072
07150-06013
.072
07150-06013
.092
07271-06414
.092
07271-07414
.110
07150-06015
.110
07150-07015
.120
07170-06805
.120
07170-07805
.141
07150-06016
.141
07150-07016
.150
07170-06806
.150
07170-07806
.179
07150-06018
.179
07150-07018
2ND OVERSIZE MANDREL - BLUE
HEAD Ø
MANDREL PART Nº
.079
07150-06213
.079
07150-06213
.102
07271-06614
.102
07271-07614
.120
07150-06215
.120
07150-07215
-
-
-
-
.151
07150-06216
.151
07150-07216
-
-
-
-
.189
07150-06218
.189
07150-07218
example
Chobert
®
1/8"
Series 1125
0.1335"
Infinite
5 (standard flat)
-example
1ST OVERSIZE MANDREL - YELLOW
HOLE
SIZE
P MAX.
HEAD Ø
MANDREL PART Nº
.119
+.004
.076
07150-06113
.119
+.004
.076
07150-06113
.120
+.005
.097
07271-06514
.120
+.005
.097
07271-07514
.136
+.005
.115
07150-06115
.136
+.005
.115
07150-07115
.126
+.005
.124
07170-06825
.126
+.005
.124
07170-07825
.157
+.005
.146
07150-06116
.157
+.005
.146
07150-07116
.150
+.005
.1535
07170-06826
.150
+.005
.1535
07170-07826
.165
+.005
.183
07150-06118
.165
+.005
.183
07150-07118
3RD OVERSIZE MANDREL - RED
HOLE
SIZE
P MAX.
HEAD Ø
MANDREL PART Nº
.126
-
-
.126
-
-
.133
-
-
.133
-
-
.149
-
-
.149
-
-
-
-
-
-
-
-
.170
+.012
.153
07150-06316
.170
+.012
.153
07150-07316
-
-
-
-
-
-
.177
-
-
.177
-
-
-example: 0.005.
1
/
" Chobert
®
& Grovit
®
.
8
-example: 07150-06804.
SPRING PART Nº
P MAX.
.123
07170-06873
.123
07170-06903
.126
07150-06814
.126
07150-07814
.142
07170-06875
.142
07170-07875
.132
07170-06875
.132
07170-07875
.164
07170-06876
.164
07170-07876
.156
07170-06876
.156
07170-07876
.171
07150-06846
.171
07150-07846
SPRING PART Nº
P MAX.
-
-
07170-06873
-
-
07170-06903
-
-
07150-06814
-
-
07150-07814
-
-
07170-06875
-
-
07170-07875
-
-
-
-
-
-
.173
07170-06876
.173
07170-07876
-
-
-
-
-
-
-
-
07150-06846
-
-
07150-07846
Advertisement
Table of Contents
