Panasonic SD XC WV-SFN480 Installation Manual page 2

The installation tasks are explained using 4 steps.
Step1 Step2
Make sure all items are prepared before Mount the brackets to a ceiling or wall.
beginning installation.
Step1 Preparations
There are 6 methods to install the camera to a ceiling or wall as described below. Prepare the
required parts for each installation method before starting the installation. The following are the
requirements for the various installation methods.
Recommended Minimum pull-
Installation method
screw
[1] Mounting the camera on the two-gang junction box
of the ceiling or wall using the A attachment plate M4 screws x 4
(accessory)
[2] Directly mount the camera onto the ceiling or wall
M4 screws x 4
using the attachment plate
[3] Placing the camera on a table using the J desk-
—
top cover (accessory)
[4] Mounting the camera on a standard tripod stand
—
(locally procured)* 1
[5] When mounting the camera on an insufficiently
strong ceiling using the WV-Q105A (ceiling mount anchor bolt x 2
brackets: approximately 150 g {0.33 lbs})*
2
M6 or M8 screws x 4 562 N {126 lbf}/ 1 pc.
[6] For mounting on ceiling
*4
(mount bracket: approx. 260 g {0.57 lbs},
M4 x 1 (for the safety
camera: 400 g {0.88 lbs}) *2
wire)
*1 Size of the camera bracket mounting hole: 1/4-20UNC camera tripod mounting hole (depth
6.0 mm (1/4 inches)).
*2 Refer to the operating instructions included with the WV-Q105A or the mounting bracket
(locally procured) for the procedure on installing the camera using the respective bracket.
*3 Make sure that the installed mount bracket can support more than 5 times of the total
weight of the camera, brackets and anchor bolt itself.
[5] [6]
K Safety wire (accessory)
Safety wire (WV-Q105A supplied)
L Washer
(accessory)
Roof space
WV-Q105A
Anchor bolt
M Spring washer
Fixing screw
(locally procured)
(accessory)
(4 pcs.
(WV-Q105A supplied))
G Cable tie (accessory)
Ceiling board such
as plaster board
A Attachment
Camera
plate (accessory)
Step3 Camera mounting
■ When using the attachment plate 2 Remove the D power cord plug (acces-
1 Insert a thin slotted head screwdriver, etc. sory) and E external I/O terminal plug
into the sub cover groove of the camera,
(accessory) attached to the camera.
rotate the slotted head screwdriver as 3 Check the position of the 3 attachment
shown in the illustration below, and then mounting screws on the bottom side of the
remove the sub cover.
camera.
Sub cover groove
Attachment mounting screws
Side cable
access hole
Sub cover sheet
Sub cover
* Wiring and the sub cover are not shown in
Note:
some illustrations from this point.
● When installing the camera directly on
the ceiling or wall with cables
IMPORTANT:
exposed, cut out a portion of the
● Because the sub cover is attached to
enclosure to open a cable access
the camera with the sub cover sheet,
hole.
do not pull the sub cover with exces-
sive force. Failure to observe this may
damage the sub cover.
● To prevent injury and protect cables,
smooth opened cable access holes of
the enclosure with a file or other tool.
● To prevent filings or other substances
entering inside the camera, open the
sub cover when using a file or other
tool to smooth the cable access
holes.
Side cable access hole
Installation
Step3
Connect cables, and then attach the
camera to the mount bracket.
IMPORTANT:
● Procure 4 screws (M4) to secure the A attachment plate (accessory) to a ceiling or a wall.
● When mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for securing.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
● Select screws according to the material of the ceiling or wall that the camera will be mount-
ed to. Do not use wood screws and nails.
out strength
● If a ceiling board such as plaster board is too weak to support the total weight, the area
196 N {44 lbf}/
shall be sufficiently reinforced.
1pc.
196 N {44 lbf}/
1pc.
Step2 Fixing the attachment plate
—
(1) Using a two-gang junction box
—
(2) Using the attachment plate (accessory)
Note:
*3
● The direction of " TOP" on the A attachment plate (accessory) determines the upwards
direction of the image on the PC monitor.
● When mounting on a ceiling, determine the direction that you want images to be dis-
played upwards on the PC monitor, and then mount so that the A attachment plate
24.5 N {5.5 lbf}
(accessory) aligns with " TOP" on C template A (accessory).
● When installing on a wall, attach the A attachment plate (accessory) so that " TOP"
faces upward.
46 mm
83.5 mm
46 mm {1-13/16
{3-9/32
{1-13/16 inches} inches}
inches}
Two-gang
junction box
Camera
TOP
mount bracket
Screw
TOP
(M6 or M8 x 4 pcs.
(locally procured))
Locking arm TOP
A Attachment
Platform plate (accessory)
Fixing M4 screws
Fixing M4 screws (4 pcs., locally procured)
Camera (4 pcs., locally procured)
4 Connect cables to the camera according to the 5 Secure the camera using the camera fixing
instructions in "Making connections", and fix screw. (Recommended tightening torque:
the camera by inserting attachment mount- 0.78 N·m {0.58 lbf·ft})
ing screws into the holes of the A attachment
plate (accessory).
Camera fixing screw
Protruding part
TOP
OPEN mark
IMPORTANT:
● Disconnect either the 12 V DC power
source or PoE power source to pre-
vent power from being supplied while IMPORTANT:
mounting the camera. ● Be sure to tighten the camera fixing
screw. Failure to observe this may cause
camera trouble due to camera falling.
Note:
(Recommended tightening torque:
● After the cables have been connected
0.78 N·m {0.58 lbf·ft})
to the camera, align the direction of
the Panasonic logo on the camera
with " TOP" of the A attachment
plate (accessory). Align the OPEN
mark on the side of the camera with
the protruding part of the attachment
plate, insert 3 attachment mounting
screws into the attachment plate,
rotate the camera approximately 15 °,
and move the LOCK mark to the pro-
truding part of the attachment plate to
temporarily secure the camera.
● After connecting the cables, use a
G cable tie (accessory) for wiring pro-
cessing as necessary.
Step3 Camera mounting (continued)
■ When installing the camera on a desktop or standard tripod stand (locally procured)
When installing the camera on a desktop or standard tripod stand (locally procured), attach the
J desktop cover (accessory) to the camera. The A attachment plate (accessory) is not used
Step4
when installing the camera on a desktop or standard tripod stand (locally procured).
Open sub cover, secure camera, close
1 Connect the cables to the camera.
after image direction adjustment. 2 Align the attachment position marker on
the desktop cover with "OPEN" on the side
of the camera, and engage the camera
attachment fixing screws in the rear of the
camera with the camera mounting holes of
the desktop cover.
OPEN
Attachment
position
marker
J Desktop
cover
(accessory)
4 When mounting on a standard tripod stand
(locally procured), attach the desktop cover
to the camera before mounting on the
standard tripod stand.
Camera mount bracket
83.5 mm
fixing screw hole
{3-9/32 inches}
(screw: 1/4-20 UNC
standard, depth 6 mm
(1/4 inches))
Cable access hole
(ø30 mm
{ø1-3/16 inches})
C Template A (accessory)
A Attachment plate
(accessory)
Step4 Adjustment
1 Loosen the SD memory card slot cover fix-
ing screw on the side of the camera using
the B bit (accessory), then insert the tip of
a small slotted head screwdriver, etc. into
the notched area to remove the SD memory
card slot cover.
2 Remove the cover film from the lens sur-
face.
3 Turn on the camera. The LINK indicator
inside the SD memory card slot cover lights.
Make sure that the ACT indicator is blinking.
(Refer to the descriptions in "Major operat-
ing controls" for more information about the
indicators.)
* After turning on the camera, there may be
a sound produced from the lens for several
seconds. This is not a malfunction.
Camera fixing
screw
SD memory card Notched area
slot cover
SD memory card slot cover fixing
screw
Image rotation gear
B Bit
(accessory)
* Part of the sub cover is not shown.
■ When mounting the camera on the WV-Q105A or the mounting bracket (locally pro-
cured)
Refer to the operating instructions included with the WV-Q105A or the mounting bracket (locally
procured) for the procedure on installing the camera using the respective bracket. The following
are descriptions of K safety wire (accessory) attachment when mounting the camera on the
3 Rotate the desktop cover in the direction of
mounting bracket (locally procured).
the arrow to secure the camera. Process
the wiring by passing the cables through the
1 Secure the H safety wire lug (accessory) to the camera with the I wire lug fixing screw
cable access hole in the desktop cover.
(accessory). Secure the safety wire lug as shown in the following illustrations.
Make sure that the attachment position
marker on the desktop cover will be set to
I Wire lug fixing screw (accessory)
the "LOCK" position.
Attachment
LOCK
J Desktop cover position marker H Safety wire lug
(accessory) (accessory)
Cable access hole
Note:
The screw hole in the J desktop cover
(accessory) is not used.
IMPORTANT:
● Because the bottom side of the cam-
era may become hot, make sure to
2 Attach the safety wire (accessory) to the wire mounting hole of the safety wire lug. (The cam-
use the camera with the J desktop
era is not shown in the following illustrations.)
cover (accessory) attached.
● The specified operating temperatures
for the camera are -10 °C to +40 °C
{14 °F to 104 °F} when it is installed
Wire mounting hole
on a desktop or standard tripod stand.
● Use a standard tripod stand with a tri-
pod head of ø75 mm or less.
● When mounting on a standard tripod
stand, take care because knocking
over the tripod or damaged screws
Pass the ring part of the safety
Tripod
may cause the camera to fall.
wire (accessory) through the wire
(locally procured)
● Use a standard tripod stand that is
mounting hole.
capable of supporting a load more
than the weight of the camera (440 g
{0.97 lbs}).
4 Perform camera settings while referring to 6 Insert an SD memory card into the slot, if
the included "Configure the settings of the necessary.
camera" (leaflet), and check if camera im-
● Insert the SD memory card with its label
ages are displayed on the PC monitor.
facing down.
5 Align the upwards direction of the image
7 Close the SD memory card slot cover, and
while rotating the image rotation gear and
tighten the SD memory slot cover slot cover
checking the image on the PC monitor.
fixing screw to secure the cover.
(Recommended tightening torque: 0.39 N·m
Rotate the image rotation gear using the bit
{0.29 lbf·ft})
(accessory), and align the upwards direction of
the image as necessary.
SD memory card
Rotating the image rotation gear clockwise
slot cover
also rotates the PC image clockwise. Rotating
the image rotation gear counterclockwise also
rotates the PC image counterclockwise.
Adjustable range of the PC image
-45° to +45°
● The default position of the image rotation
Image rotation gear
gear is 0°.
Note:
● When Double Panorama or Panorama
is selected for the Image capture
mode, you can rotate the image at 90°
SD memory card slot cover fixing screw
intervals by using preset position set-
tings. To make further fine adjustments
* Part of the sub cover is not shown.
to the image angle, adjust the image
rotation gear. Refer to 11.1 and 11.5.4
● To remove the SD memory card, hold down
of the Operating Instructions for more
the SD ON/OFF button for about 2 seconds.
information.
When the flashing SD MOUNT indicator
goes out, you can remove the SD memory
card.
Note:
● After the SD memory card has been
Take care of the following points when
replaced, press the SD ON/OFF button, and
using monitor out.
make sure the SD MOUNT indicator is con-
● Select "9M Fisheye" or "4M Fisheye"
tinually lit.
for "Image capture mode".
● If you do not press the SD ON/OFF button
● Locally procure the ø3.5 mm monaural
after replacing the SD memory card, the SD
mini plug⇔RCA pin jack conversion
MOUNT indicator is continually lit approxi-
cable.
mately 5 minutes later.
● Select the [Setup]→[Basic] tab, and
then select On (NTSC) or On (PAL) for
[Monitor out].
IMPORTANT:
● Make sure to attach the safety wire lug so
Wire lug fixing
that the wire mounting hole faces outward.
screw hole
When it is attached facing inward, it may
touch the camera mount bracket.
● Use the I wire lug fixing screw (accesso-
ry) to attach the H safety wire lug (acces-
sory). When using different length screws,
it may damage the camera or cause the
camera to fall.
(Recommended tightening torque:
0.39 N·m {0.29 lbf·ft})
Safety wire lug
attachment example
Wire mounting hole
Safety wire
(accessory)
Pass the other end of the safety
wire through the ring part of the
safety wire.
8 Return the sub cover to its original position
and secure it.
SD memory card
Sub cover exterior
Sub cover interior
Sub cover exterior hook
Sub cover
interior hook
● Secure the sub cover exterior hook first,
then push in the interior hook.
IMPORTANT:
● Ensure that the SD memory card slot
cover's fixing screw is firmly secured.
● Make sure that the sub cover is
securely fixed.
● After the installation is completed,
clean the lens surface with a soft
cloth, etc.
● After the installation is complete, if the
image is out of focus, turn off the
camera, and then turn it on again. If
the image is still out of focus, select
the [Image/Position] tab from
[Setup]→[Image/Audio], and then re-
adjust the back focus from [Setup>>]
of [Back focus].
* When removing the camera, perform
removal by following the installation
procedure in the reverse order.