Philips HQ6832/A Service Manual

!
Service
Information
Philips Domestic Appliances and Personal Care
Service Manual
R1
D3
T1
L1
C7
Mains D4
D1
C1 C2
D2
D5
IC3
R5
1 8 R2
SRC DRN
2 5
GND VAUX
C4
3 7
CBT NC C3
6
R6
GND
R4
4
RREF
Power plug
Power module
TIPS FOR REPAIR
- Remove the shaving unit to prevent damage during repair.
- Remove screws A1 (2x, of which 1 is under trimmer slide).
- After the cover (item 27) has been removed, it must be
checked if the rubber seal (item 3) has not been damaged.
- The cover contains a sticker that is permeable to gas yet
impermeable to water.
This sticker may nor be removed under any circumstances.
- Remove the metal brackets.
- Unsolder the motor connector and remove the PCB.
- To replace the motor (item 20) or the driving unit (item 16),
screws B1 must be removed fi rst.
- Then push the entire unit out of the housing (item 2) and
check if its sealing is damaged.
- Detach the motor clamping springs (item 21) with a small
screwdriver.
- The entire driving unit (item 16) is supplied as a single part
to guarantee optimal sealing of the gear shafts.
- To guarantee that the shaver is completely watertight, only
the original screws may be used.
- To charge the shaver only the original HQ6000 power plug
may be used.
Published by Philips Domestic Appliances and Personal Care
4322 277 00593
02/12
D1
R3
R18
C8 D6
5 14 IC2a
2
R19
4
6 3
7 R20
SK1
C6
R21
C5
C4 C5 C6
C10
R29
TS6a
R32
D5
C11
R35 R31
TS6b
R34 R30
Printed in the Netherlands

Rechargeable shaver

IC2b
TS5
1
C7
IC2c IC2d
8 11
C8
D4a D4b
10 13
9 12
R22 R23
R25 R1 R4 R5
R41
R27
R17
R3
C2
R33
TS1
R26
TS7
D3
R39
R28 R2
R40
TECHNICAL DATA
Input voltage
Power consumption
Motor voltage
Battery
Battery capacity
Charging indicator
Charging time
Charging current
Power supply
Shaving heads
Cleaning
Comfort control
Mains shaving
SAP CODING
© Copyright reserved
HQ6832/A
QUADRA ACTION
C9 R36 PM
R13
D43
R14
TS9
L3
C3
MF2
D6 R24
R6 R15 R11
TS2
IC1
8 6
VCC TH
2
TR
TS3
5
CV
R7
3
Q
4
R38 TS4
R
R8
1 7
GND DIS TS8
R37 R12 R10 R16
: 100-240 V, 50/60 Hz
: max. 7 W
: 2.4 V
: 2x NiMH AA
: approx. 1100 mAh
: 1x LED green - charge
: approx. 1 hour
: initial 4 hours
: 1100/40 mA temp. dependent
: HQ6000 external transformer
: HQ6010 car cord
: HQ6 - 4822 690 10214
: wet / dry
: fi xed setting
: 3-D contour following
: yes
: HQ6832
Subject to modification
A
NiMH
2 x AA
R9
L1
D2
MF1
C1