Draytek Vigor2762 Quick Start Manual
  1. Manuals
  2. Brands
  3. Draytek Manuals
  4. Network Router
  5. Vigor2762 series
  6. Quick start manual

Draytek Vigor2762 Quick Start Manual

Adsl2/2 + & vdsl2
Hide thumbs Also See for Vigor2762:
Table of Contents

Advertisement

Quick Links

See also: User Manual
i

Advertisement

Table of Contents
loading

Related Manuals for Draytek Vigor2762

Summary of Contents for Draytek Vigor2762

  • Page 2: Quick Start Guide

    We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from a DrayTek authorized dealer in the UK/Ireland.

  • Page 3: European Community Declarations

    Product: Vigor 2762 Series DrayTek Corp. declares that the Vigor2762 Series of routers are in compliance with the following essential requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU, ErP 2009/125/EC and RoHS 2015/863/EU, Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU by complying with the requirements set forth in EN55032/Class B, Low Voltage (LVD) Directive 2014/35/EU by complying with the requirements set forth in EN60950-1.
  • Page 4 The outside of the product’s box will state the region compatibility (e.g. “Applied Region: UK”). If you are unsure, check with DrayTek or your supplier. The use of unofficial components (e.g. PSUs) or adapting interfaces or the use of unauthorized software/firmware may cause malfunction, product damage or personal danger and...

  • Page 5: Table Of Contents

    1. Introduction ......................1 2. Package Contents ....................2 3. Panel Explanation ....................3 3.1 Vigor 2762n ..........................3 3.2 Vigor 2762ac ..........................5 4. Installing your Vigor 2762 router ................. 7 4.1 Wall-Mounting the Vigor 2762 ....................8 5. Setup & Configuration ..................9 5.1 Accessing the Router Web Interface ..................

  • Page 6: Introduction

    The Vigor2762 series is an ADSL2+ / VDSL2 router / firewall with guest network capability for fast and secure home and small office connectivity, designed for bandwidth-intensive applications such as high-definition video streaming, online gaming and Internet telephony. Packed with advanced features, the Vigor 2762 series offers truly comprehensive DSL connectivity and security.

  • Page 7: Package Contents

    DrayTek Vigor 2762 router Quick Start Guide (This document) RJ-45 Cable (Ethernet) RJ-11 to RJ-11 Cable (Connects to your PC or Switch) (Connects to your DSL line) UK Power Adapter Antenna...

  • Page 8: Panel Explanation

    Status Explanation Blinking The router is ready and operating normally The router is powered off (Activity) 2.4GHz Access Point is active Blinking Data is being transmitted on the router’s 2.4 (Wireless LAN GHz wireless interface On/Off/WPS) Blinking in WPS pairing mode is active for two minutes unison with (Activity) 2.4GHz Access Point is turned off...
  • Page 9 Interface Description Wireless LAN WLAN On - Press the button and release it within 2 seconds. ON/OFF/WPS When the wireless function is enabled, the green LED will be WLAN Off - Press the button and release it within 2 seconds to turn off the WLAN function.

  • Page 10: Vigor 2762Ac

    Status Explanation Blinking The router is ready and operating normally The router is powered off (Activity) 2.4GHz Access Point is active (2.4GHz Blinking Data is being transmitted on the router’s 2.4 Wireless LAN GHz wireless interface On/Off/WPS) Blinking in WPS pairing mode is active for two minutes unison with (Activity) 2.4GHz Access Point is turned off...
  • Page 11 Interface Description Wireless LAN Press for less than 2 seconds to switch toggle the router’s ON/OFF/WPS wireless interfaces: For example, 2.4G (On) and 5G (On) – Default state. 2.4G (Off) and 5G (On) – press and release the button once. 2.4G (On) and 5G (Off) –...

  • Page 12: Installing Your Vigor 2762 Router

    ADSL/VDSL Connections: Connect the DSL port to the Modem or DSL port of the external splitter/microfilter (not supplied) with the RJ-11 line cable. In some cases, your RJ-11 DSL socket will be built-into your phone line socket on the wall and you won’t have a separate microfilter/splitter.

  • Page 13: Wall-Mounting The Vigor 2762

    DrayTek Vigor 2762 series routers have keyhole type mounting slots on the underside to hang the router on, using screws attached to a wall or other surface. A template is provided in the Vigor router packaging box to enable you to...

  • Page 14: Setup & Configuration

    & & This section provides examples of how to initially access the router and configure internet access for the most common types of Internet connection in the UK. If the instructions in this quick start guide do not allow you to get online with your ISP or type of Internet connection, there are additional guides available on in the Product Knowledgebase.
  • Page 15 This is from Microsoft Edge: Most other browsers will present equivalent warnings. In each case, following the prompts/links will allow you to access the router's web interface. It is still encrypted with SSL/TLS. Note This warning appears because the router's default certificate is 'self-signed' rather than issued to you by a certificate authority who has verified your identity.
  • Page 16 Note If you cannot access the web interface, please go to the “Trouble Shooting” section in the User Guide to determine the cause of and solve your problem. Upon successful login, the router will display the Dashboard, which shows a summary of the router model, WAN status, front panel port status and other information: Note...

  • Page 17: Wan1 - Adsl And Vdsl2 Connection Setup

    The WAN1 interface of the Vigor 2762 router can connect to either an ADSL / ADSL2+ connection or a VDSL2 connection. If your Internet connection uses VDSL2 and your ISP has supplied you with a Username and Password to connect to the Internet, go to section 5.2.1 PPPoE connection with FTTC VDSL2 If your Internet connection uses VDSL2 and your ISP does not supply or require a Username and Password to connect to the Internet, go to section...
  • Page 18 Openreach VDSL2 network, if your ISP operates on a different VDSL2 network, this tag value may differ; please check with your ISP or the DrayTek UK Knowledgebase for ISP specific guides. Click OK on that page to apply the changes.
  • Page 19 3. Go to [WAN] > [Internet Access] Firstly set the WAN1 Access Mode to PPPoE / PPPoA, then click the Details Page button to proceed: 4. On the PPPoE / PPPoA settings tab: Select the Enable radio button at the top of the page to ensure that the PPPoE interface is enabled.
  • Page 20 5. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the VDSL information and PPP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully: Note If the WAN 1 IP address displayed begins with 172.16.x.x, it’s possible that the ISP has not accepted the supplied Username and Password for the Internet connection.
  • Page 21 1. Go to [WAN] > [General Setup] and click on the WAN1 link: 2. On the settings page: • Set the Enable option to Yes to activate the WAN1 connection • Set the Active Mode to Always On • Enable the Service – VLAN Tag insertion •...
  • Page 22 Openreach VDSL2 network, if your ISP operates on a different VDSL2 network, this tag value may differ; please check with your ISP or the DrayTek UK Knowledgebase for ISP specific guides. Click OK on that page to apply the changes.
  • Page 23 Click OK on this page to apply the changes and the router will then prompt to restart. Click the OK button to restart the router. 5. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the VDSL information and DHCP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully:...

  • Page 24: Pppoa Connection With Adsl / Adsl2

    1. Go to [WAN] > [Internet Access] Firstly set the WAN1 Access Mode to PPPoE / PPPoA, then click the Details Page button to proceed: 2. On the PPPoE / PPPoA settings tab: The details for the VPI and VCI settings for ADSL should be correct for UK usage, with 0 and 38 being the defaults.

  • Page 25: Wan2 - Ethernet Connection Setup

    3. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the ADSL information and PPP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully: Note If the WAN 1 IP address displayed begins with 172.16.x.x, it’s possible that the ISP has not accepted the supplied Username and Password for the Internet connection.

  • Page 26: Enabling The Ethernet Wan Port

    The Vigor 2762 series router uses the GigaLAN4 port to connect to an Ethernet based Internet connection. In its default state, the GigaLAN4 port operates as a standard LAN port and the WAN2 (Ethernet WAN) options cannot be selected in the router’s web interface.
  • Page 27 3. Set the Enable option for WAN2 to Yes, this enables the other options on this page. Set the Active Mode to Always On to make the Ethernet port the active Internet connection. 4. Click OK to apply the change and the router will prompt to restart. Click OK to restart the router.

  • Page 28: Pppoe

    This connection method will typically be used with a modem such as the Vigor 130 VDSL2 modem, which passes through the PPPoE connection from the ISP to the router. 1. Go to [WAN] > [Internet Access] Firstly set the WAN2 Access Mode to PPPoE, then click the Details Page button to proceed: 2.

  • Page 29: Static Or Dynamic Ip

    1. Go to [WAN] > [Internet Access] Firstly set the WAN2 Access Mode to Static or Dynamic IP, then click the Details Page button to proceed: 2. In the Static or Dynamic IP settings: Select the Enable option and select Obtain an IP address automatically which will obtain an IP from the ISP with DHCP.

  • Page 30: Wan3 / Wan4 - 3G / 4G Usb Modem Setup

    USB modem to provide internet access through the router. The list of supported modems can be found under: [USB Application] > [Modem Support List] or on the DrayTek UK site: https://www.draytek.co.uk/support/guides/usb-3g-4g-modem-support-list There are two USB modem connection modes available:...
  • Page 31 To set the APN Name, enter the APN required by the SIM card / network into the APN Name field and click the Apply button: This will move the APN Name into the Modem Initial String to indicate that it has been saved.

  • Page 32: Dhcp Mode

    To set up the USB WAN for DHCP mode, go to [WAN] > [Internet Access] Select 3G/4G USB Modem (DHCP mode) from the drop-down box Click the Details Page button to continue: In the USB WAN settings, select the Enable option to enable the WAN interface. Enter a SIM PIN code only if your SIM card has a PIN set on it, otherwise leave this blank.

  • Page 33: Getting Further Help

    Internet connectivity and more advanced features: https://www.draytek.co.uk/support/product-knowledgebase Now that you have your DrayTek product, you should keep up to date with product updates (firmware), security advisories and other product news, advice or special offers. Users in the UK/Ireland can subscribe to our mailing list. For...

  • Page 34: Firmware Updates

    - simple mistakes which could then be exploited by others. We've produced our free guide "Router Best Practice" which contains essential information for anyone installing, configuring or using a broadband router or wireless LAN. Available to download: https://www.draytek.co.uk/best...

Table of Contents