Page 1
(Wireless models) Guide Version: Region: United Kingdom & Ireland For updates and support, visit www.draytek.co.uk March 2022 / Firmware V4.2.3 Note: Product specification is subject to continuous evolution which may not always be reflected in current documentation. For the formal specification...
Page 2
We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from a DrayTek authorized dealer in the UK/Ireland. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase.
Page 3
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2763 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2763/Document/CE/ Manufacturer: DrayTek Corp. Address: No.
DrayTek Vigor router Quick Start Guide and Antenna (This document) RJ-45 Cable (Ethernet) RJ-11 to RJ-11 Cable (Connects to your PC or Switch) (Connects to your DSL line) UK Power Adapter The maximum power consumption is 17-23 Watts. Important Remove the protective film from the router before use to Note ensure ventilation.
Status Explanation Blinking The router is ready and operating normally The router is powered off (Activity) DSL connection synchronised Blinking DSL connection not currently synchronizing or (DSL) (Slowly) not detected Blinking DSL connection is synchronising (Quickly) On (Green) 2.4GHz Access Point is active Blinking Data is being transmitted on the router’s 2.4 (Wireless LAN...
Page 7
P1~P4 RJ-45 Gigabit Ethernet connectors for local network devices. LAN port P4 can be configured as the Ethernet WAN port, see: https://www.draytek.co.uk/support/guides/kb-ethernetwan-enable RJ-11 connector for ADSL or VDSL line Power Switch. Turns the unit on (I) or off (O) Connector for the power adapter...
Status Explanation Blinking The router is ready and operating normally The router is powered off (Activity) DSL connection synchronised Blinking DSL connection not currently synchronising or (DSL) (Slowly) not detected Blinking DSL connection is synchronising (Quickly) The phone connected to this port is off-hook The phone connected to this port is on-hook Blinking A phone call is incoming...
Page 9
Thermometer P1~P4 RJ-45 Gigabit Ethernet connectors for local network devices. LAN port P4 can be configured as the Ethernet WAN port, see: https://www.draytek.co.uk/support/guides/kb-ethernetwan-enable RJ-11 connector for ADSL or VDSL line Phone2/Pho RJ-11 connectors for VoIP usage with analogue telephones Power Switch. Turns the unit on (I) or off (O)
Here we take the Vigor2763ac as an example. ADSL/VDSL Connections: Connect the DSL port to the Modem or DSL port of the external splitter/microfilter (not supplied) with the RJ-11 line cable. In some cases, your RJ-11 DSL socket will be built-into your phone line socket on the wall and you won’t have a separate microfilter/splitter.
DrayTek Vigor 2763 series routers have keyhole type mounting slots on the underside to hang the router on, using screws attached to a wall or other surface. Drill two holes on the wall. The distance between the holes shall be 168mm.
& & This section provides examples of how to initially access the router and configure internet access for the most common types of Internet connection. If the instructions in this quick start guide do not allow you to get online with your ISP or type of Internet connection, contact your dealer for advanced information.
Page 13
An example from Microsoft Edge, click “Continue to this webpage” to proceed: Most other browsers will present equivalent warnings. In each case, following the prompts/links will allow you to access the router's web interface. It is still encrypted with SSL/TLS. Note This warning appears because the router's default certificate is 'self-signed' rather than issued to you by a certificate authority...
Page 14
Note If you cannot access the web interface, please go to the “Trouble Shooting” section in the User Guide to determine the cause of and solve your problem. Upon successful login, the router will display the Dashboard, which shows a summary of the router model, WAN status, front panel port status and other information: Note...
– & – & The WAN1 interface of the Vigor 2763 router can connect to VDSL2 and ADSL2+ lines. If your Internet connection uses VDSL2 and your ISP has supplied you with a Username and Password to connect to the Internet, go to section 4.2.1 PPPoE connection with FTTC VDSL2 If your Internet connection uses VDSL2 and your ISP does not supply or require a Username and Password to connect to the Internet, go to section...
Page 16
Click OK on that page to apply the changes. Go to [WAN] > [Internet Access] Set the WAN1 Access Mode to PPPoE / PPPoA, then click the Details Page button to proceed: On the PPPoE / PPPoA settings tab: Select the Enable radio button at the top of the page to ensure that the PPPoE interface is enabled.
Page 17
Click OK on this page to apply the changes and the router will then prompt to restart. Click the OK button to restart the router. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the VDSL information and PPP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully:...
Page 18
Note If the WAN 1 IP address displayed begins with 172.16.x.x, it’s possible that the ISP has not accepted the supplied Username and Password for the Internet connection. Check that the ISP Access Setup - Username and Password match the details supplied by your ISP. Go to [WAN] >...
Page 19
Click OK on that page to apply the changes. Go to [WAN] > [Internet Access] Set the WAN1 Access Mode to MPoA / Static or Dynamic IP, then click the Details Page button to proceed: In the MPoA / Static or Dynamic IP settings: Select the Enable option and select Obtain an IP address automatically which will obtain an IP from the ISP using DHCP.
Page 20
Click OK on this page to apply the changes and the router will then prompt to restart. Click the OK button to restart the router. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the VDSL information and DHCP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully:...
Go to [WAN] > [Internet Access] Set the WAN1 Access Mode to PPPoE / PPPoA and click the Details Page button to proceed: On the PPPoE / PPPoA settings tab: The details for the VPI and VCI settings for ADSL should be correct for UK usage, with 0 and 38 being the defaults.
Page 22
Click OK on this page to apply the changes and the router will then prompt to restart. Click the OK button to restart the router. Once the router has restarted, the [Online Status] > [Physical Connection] page will display the ADSL information and PPP connection status, if the WAN1 section shows an IP address, it has connected to the internet successfully: Note...
Vigor2763 series router is capable of very much more and has a plethora of other features. These are covered in the main user manual. Now that you have your DrayTek product, you should keep up to date with product updates (firmware), security advisories and other product news, advice or special offers.