ICE MAKER Use & Care Guide For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at... www.kitchenaid.com In Canada, for assistance, installation and service, call: 1-800-807-6777 or visit our website at... www.kitchenaid.ca FÁBRICA DE HIELO Manual de uso y cuidado Para consultas respecto a características, funcionamiento/desempeño, piezas, accesorios o servicio, llame al: 1-800-422-1230...
ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
Option 2—With Hinge-Side Spacers Location Requirements ■ To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed in on the top and 3 sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.
IMPORTANT: If this product is connected to a GFCI (Ground Tools Needed Fault Circuit Interrupter) equipped outlet, nuisance tripping of the Gather the required tools and parts before starting installation: power supply may occur, resulting in loss of cooling. Ice quality ■...
⁵⁄₁₆" I.D. x 32" (81 cm) vent tube (drain pump reservoir vent Rear View ■ to ice maker cabinet back) ■ Cable clamps (secures vent tube to back of ice maker) (3) #8-32 x ³⁄₈" pump mounting screws (secures drain pump to ■...
Page 7
Water Supply Line Drain Tube ⁷⁄₈ ⁷⁄₈ " adjustable hose clamp " adjustable hose clamp B. Drain tube (ice bin to drain pump) D. Drain pump reservoir inlet ¹⁄₄ " copper tubing D. Ferrule (sleeve) 5. Install vent tube (⁵⁄₁₆" I.D. x 32" [81 cm]) to drain pump reservoir vent.
Page 8
Drain Pump Mounting Tab Slot Vent Tube NOTE: Do not pinch, kink, or damage the vent tube. Check that it is not damaged, pinched, or kinked between the cabinet and the ice maker. A. Mounting tab slot Drain Pump Installed A.
NOTES: Drain Connection ■ If the drain hose becomes twisted and water cannot drain, your ice maker will not work. Gravity Drain System ■ It may be desirable to insulate the drain line thoroughly up to the drain inlet. Insulation Sleeve kit Part Number W10365792 is available for purchase.
Door Reversal—Side Swing Only Tools Needed Gather the required tools and parts before starting installation. ⁵⁄₁₆" wrench ■ ■ Flat putty knife ¹⁄₄" wrench ■ ■ Phillips screwdriver ⁵⁄₁₆ Hinge pin " hex-head hinge screw Handle screw End cap screw A.
Top Hinge 3. Install the white decorative screws on the opposite side of the door. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. A.
7. Use the level to recheck the ice maker to see that it is even 4. Using the arrow pointing to the alignment pin on the side of from front to back and side to side. If the ice maker is not the filter and the arrow inside the control housing, align the level, repeat steps 2 through 5.
5. Cubes fall into the storage bin. When the bin is full, the ice Replace the Water Filter maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will To purchase a replacement water filter, see the “Accessories” occur.
Ice Maker System Normal Sounds Your new ice maker may make sounds that are not familiar Minerals that are removed from water during the freezing cycle to you. Because the sounds are new to you, you might be will eventually form a hard, scaly deposit in the water system. concerned about them.
Page 15
5. Unplug the wiring harness from the left side of the cutter grid. Condenser A Dirty or Clogged Condenser ■ Obstructs proper airflow. ■ Reduces ice making capacity. ■ Causes higher-than-recommended operating temperatures which may lead to component failure. WARNING A.
■ Replace the ice scoop holder by replacing the screws. 12. To replace the water pan, set the water pan inside the ice bin. Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the water pan by replacing the mounting screw.
TROUBLESHOOTING Try the solutions suggested here first in order to avoid the cost of an unnecessary service call. Ice Maker Operation WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord.
Ice Production WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. PROBLEM RECOMMENDED SOLUTIONS Ice Maker Runs but Check that the control is turned on. Produces No Ice Check that the water supply is properly connected and turned on.
200 - 6750 Century Ave. Mississauga, Ontario L5N 0B7 Please include a daytime phone number in your correspondence. Accessories To order accessories, in the U.S.A., visit our website www.kitchenaid.com/accessories or call 1-800-901-2042. In Canada, visit our website www.whirlpoolparts.ca or call 1-800-807-6777. ® Water Filter...
PERFORMANCE DATA SHEET Ice Maker Water Filtration System Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 Gallons (7571 Liters) System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor. This system has been tested according to NSF/ANSI Standards 42 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42.
Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.kitchenaid.com. 2. All warranty service is provided exclusively by our authorized KitchenAid Service Providers. In the U.S. and Canada, direct all requests for...