Installation - Honeywell S9200U1000 Installation Instructions Manual

Table 1. S9200U1000 Replaces These Integrated
Furnace Controls.
[Only use the S9200U1000 on 120 Vac applications.]
SKU Harness
50A50-113
50A50-295
50A50-296
50A50-408
50A50-241
A
Inducer & HSI
Connector
50A55-143
G
50A55-288
A
Inducer & HSI
50A50-285
Connector
50A55-285
G
1
Amana
10207701
A
10207702
Inducer & HSI
10207703
Connector
10207710
ICP
1010806
A
1380-686
Inducer & HSI
Connector
1380-699
Lennox
1214201
A
Inducer & HSI
Connector
1
Wiring harness G should be used if the control being
replaced has a 2-pin inducer/igniter connector instead of
a 4-pin inducer/igniter connector.
S9200U1000 UNIVERSAL HOT SURFACE IGNITION INTEGRATED FURNACE CONTROL
Field Settings Settings -
Recommendation - DIP Switch
DIP Switch S1
SW1: ON
SW2: OFF
SW3 & SW4: 60/90/
120/180
SW1: ON
SW2: OFF
SW3: ON
SW4: OFF
SW1: OFF
SW2: ON
SW1: ON
SW2: OFF
SW3 & SW4: 60/90/
120/180
SW1: OFF
SW2: OFF
SW3 & SW4: 60/90/
120/180
SW1: ON
SW2: OFF SW1: OFF
SW3 & SW4: 60/90/ SW2: ON
120/180
SW1: ON
SW2: 30/60
SW3 & SW4: 60/90/
120/180
SW1: ON
SW2: OFF
SW3 & SW4: 60/90/
120/180
SW1: OFF
SW2: OFF
SW1: OFF
SW2: OFF
SW3: ON
SW4: OFF
SW1: ON
SW2: OFF
SW3 & SW4: 60/90/
120/180
SW1: ON
SW2: OFF SW1: OFF
SW3: ON SW2: ON
SW4: OFF
SW1: OFF
SW2: OFF
SW1: ON
SW2: OFF SW1: OFF
SW3 & SW4: 60/90/ SW2: ON
120/180
SW1: OFF
SW2: ON
SW1: ON
SW2: OFF SW1: OFF
SW3: ON SW2: OFF
SW4: OFF
NOTE: To replace controls in Table 2, a jumper
(included with harness kit) may be required
to short out the rollout switch on the main 12-
pin connector plug from the furnace. The roll-
Safety
out switch is located between pins 5 and 11
Timing
on the 12-pin connector. Refer to Table 3 and
Fig. 2 on page 7.
S2
Table 2. Replacing Additional Controls.
[Only use the S9200U1000 on 120 Vac applications.]
SKU
D330927P01
D330930P01
D330934P01
D340035P01
D340354P01
D340774P01
D341235P01
50A50-571
50A55-571
50A50-473
50A50-474
50A50-405
50A50-406
50A50-471
50A55-474
50A55-438

INSTALLATION

When Installing This Product...
1. Read these instructions carefully. Failure to follow
them could damage the product or cause a hazard-
ous condition.
2. Check the ratings given in these instructions to
make sure the integrated furnace control is suitable
for your application.
3. Installer must be a trained, experienced service
technician.
4. After installation is complete, check out operation
as provided in these instructions.
5
Field Settings
Recommendatio
n - DIP Switch
Harness S1
SW1: ON
SW2: OFF
SW3 & SW4: 60/
90/120/180
SW1: OFF
SW2: OFF
SW3 & SW4: 60/
90/120/180
Jumper
SW1: ON
(Roll-out
SW2: OFF
Switch)
SW3: ON
SW4: OFF
SW1: ON
SW2: OFF
SW3 & SW4: 60/
90/120/180
SW1: OFF
SW2: OFF
SW3: ON
SW4: OFF
SW1: OFF
SW2: OFF
A
SW3 & SW4: 60/
Inducer & HSI
90/120/180
Connector
SW1: OFF
SW2: OFF
SW3: ON
SW4: OFF
SW1: Check
Settings
SW2: OFF
SW3 & SW4: 60/
90/120/180
Safety
Timing
Settings -
DIP Switch
S2
SW1: OFF
SW2: OFF
SW1: OFF
SW2: ON
SW1: OFF
SW2: OFF
SW1: OFF
SW2: ON
SW1: OFF
SW2: OFF
SW1: OFF
SW2: OFF
69-2075EF—01