Cisco uBR10012 Hardware Installation Manual page 36

Upgrading to Cisco 10000 Series SPA Interface Processor-600
If a TFTP server is available, use the copy running-config tftp command. If a TFTP server is not available,
copy the configuration file to the PRE flash drive and transport the configuration file to a system that can be
used to edit the file.
Step 3
Open the configuration file in a text editor and search for the string 2jacket-1 and replace it with 4jacket-1.
After replacing this string, the line should read card 1 4jacket-1 where 1 is the slot location of the Cisco 10000
Series SPA Interface Processor-600.
Note
Step 4 Search for all configurations related to bay 0 in the configuration file and change it to bay 3 as shown below:
Change card 1/0 24rfchannel-spa-1 to card 1/3 24rfchannel-spa-1.
Change controller modular-cable 1/0/0 to controller modular-cable 1/3/0.
Step 5 Search for every wideband interface related to bay 0 and change bay 0 to bay 3.
Search for the string interface wideband-cable1/0/0 and change all instances of it to interface
wideband-cable1/3/0. For example, a line such as interface wideband-cable1/0/0:0 changes to interface
wideband-cable1/3/0:0.
Step 6 Search for the string downstream modular-cable 1/0/0 and change all instances of it to downstream
modular-cable 1/3/0.
Step 7 Once the configuration file has been edited for use with the Cisco 10000 Series SPA Interface Processor-600,
copy the configuration file back to the PRE. If a TFTP server is available, use the copy tftp ubr10k-config
startup-config command.
If a TFTP server is not available, copy the configuration file back to the PRE flash drive, and then transport
the file to the PRE.
Step 8 Remove Cisco Wideband SPAs from the Cisco Wideband SIP. Then remove the Cisco Wideband SIP.
Note
Step 9 Insert the Cisco 10000 Series SPA Interface Processor-600 in the same slot from which the Cisco Wideband
SIP was removed. If the Cisco Wideband SIP was in slot 1/2, insert the Cisco 10000 Series SPA Interface
Processor-600 in slot 1/2.
Step 10 If a PRE 4 is in use or a PRE 4 upgrade is planned immediately after the Cisco 10000 Series SPA Interface
Processor-600 upgrade, then insert Cisco Wideband SPAs in bays 0 and 1 of the Cisco 10000 Series SPA
Interface Processor-600.
Once inserted, restore the cable connections. Attach the cable from Cisco Wideband SIP bay 0 to the
Cisco Wideband SPA in bay 0 of the Cisco 10000 Series SPA Interface Processor-600. Attach the cable from
Cisco Wideband SIP bay 1 to the Cisco Wideband SPA in bay 1 of the Cisco 10000 Series SPA Interface
Processor-600.
Cisco uBR10012 Universal Broadband Router SIP and SPA Hardware Installation Guide
28
If you are using a PRE2 and do not plan to upgrade to a PRE4, then continue with Step 4, Step 5,
and Step 6, as additional changes must be made to the configuration file for a PRE2. If you plan to
use a PRE4 after upgrading to the Cisco 10000 Series SPA Interface Processor-600, skip Steps 4
through 6, and resume with Step 7. The Cisco Wideband SPA cannot be adjacent to a WAN SPA
when the Cisco 10000 Series SPA Interface Processor-600 is used with a PRE2. Therefore, when
Cisco Wideband SPAs are moved from the Cisco Wideband SIP to the Cisco 10000 Series SPA
Interface Processor-600, they must be placed in bays that differ from the original Cisco Wideband
SIP configuration. The recommended bays for the Cisco 10000 Series SPA Interface Processor-600
are 1 and 3. So you need to search for all configurations related to bay 0 in the configuration file and
change it to bay 3. The configuration for bay 1 remains intact.
Make a note of which cable is connected to which Cisco Wideband SPA. Later, the cable connections
must be restored to the correct bay.
Overview of SPA Interface Processors