Extreme Networks ERS 4950GTS Quick Installation

Ethernet Routing
Switch 4900 Series
Quick Installation for Ethernet Routing Switch 4900 Series
You can download all documents referenced in this Quick Installation Guide at
http://www.extremenetworks.com/documentation/.
Depending on your hardware model, your switch can appear different than the figures
shown in this guide.
1

Before you start

Confirm that you have the following tools and package contents:
Tools required:
• Phillips #2 screwdriver
• Console cable
• Console cable or Ethernet cable (if using the default IP address to access the
device for configuration)
Package contents:
2
3
4
5
1. Ethernet Routing Switch 4900 Series.
2. Rack-mounting hardware that includes:
• Rack-mount brackets (2)
• Screws to attach brackets to the switch (8)
• Screws to attach the switch to the equipment rack (3 x 4).
3. Standard .5 m stacking cable.
4. Documentation includes the Quick Install poster and Regulatory documents.
5. Field replaceable power supply.
Note: Two field replaceable power supplies are supported for models ERS 4950GTS,
ERS 4926GTS, ERS 4950GTS-PWR+, and ERS 4926GTS-PWR+. One power supply is
already installed.
Note: Ensure to order Direct Attach cables and SFP or SFP+ Transceivers
if required.
Other optional requirements:
REPLACEMENT/OPTIONAL POWER SUPPLY UNITS
Model Primary PSU
ERS 4950GTS, 250W AC power supply
ERS 4926GTS (replacement order code:
AL1905A09-E6)
ERS 4950GTS-PWR+, 1025W AC POE+ power supply
ERS 4926GTS-PWR+ (replacement order code:
AL1905A19-E6)
Note: Power cords must be ordered separately. For information about order codes, see
Installing Ethernet Routing Switch 4900.
CABLES FOR INSTALLING THE SWITCH INTO A NETWORK
Product Number Name
AL2011022-E6 RJ-45/DB-9
CONSOLE CABLE
AL2011020-E6 RED DB-9 FEMALE TO
RJ-45 ADAPTOR
STACKING CABLES FOR STACKING
Material code Description
700511668 0.5 m stacking cable
700511669 1.5 m stacking cable
700511670 3.0 m stacking cable
700511671 5.0 m stacking cable
1
Optional Secondary PSU
250W AC Power Supply
(order code: AL1905A09-E6)
1025W AC power supply (order
code: AL1905A19-E6)
Short Description
1.5m cable with DB-9 Female for
terminal/PC on one end and RJ-45 for
device console port connectivity on
the other.
Converts DB-9 MALE to RJ-45 serial
port. The adaptor can be used for PC or
device with DB-9 MALE console port.
Also, can be used with Category 5
RJ-45 straight cable to provide
console connection.
2
Prepare the rack
1. Provide the equivalent of one rack of vertical space for each switch in an EIA or
IEC-standard 19-inch (48.2-centimeter) equipment rack.
2. Ensure that the equipment rack is stable and securely attached to a
permanent structure.
3. Ground the rack to the same grounding electrode used by the power service in the
area. The ground path must be permanent and must not exceed 1 Ohm of
resistance from the rack to the grounding electrode. Using a filter or surge suppressor
is recommended.
3
Front-mount the switch in a rack
1. Attach the brackets to each side of the device using the screws provided.
2. Slide the switch into the rack. Insert and tighten the rack-mount screws.
To rear-mount the switch in a rack, see Installing the Ethernet Routing Switch
4900 Series.
4
Stacking
The ERS 4900 Series provides fail-safe stackability. You can connect up to eight 4900 Series
devices in a stack to provide uninterrupted connectivity for up to 400 ports. The stack is
managed as single unit, using the IP address of the base unit.
ERS 4900 series rear panel
The switch back panel provides a Base Unit Select switch, Cascade Down connector, and
Cascade Up connector for stacking purposes as shown below:
Cascade Cascade Ports
Up Down
Base Unit Select switch – used to designate the base unit in a stack. When set DOWN, this unit
acts as the Base Unit for the stack. Only one switch in the stack must have the Base Unit Select
in base position.
Ports – used for device management and cannot be used to access network (out-of-band
management). For more information, see Quick Start Configuration for Ethernet Routing
Switch 4900 and 5900 Series.
Note: The port labeled AUX is disabled.
Cascade Down and Cascade Up connectors – used connect a switch to the next unit in the
stack through a cascade cable. Connect one end of the Cascade Down cable to the Cascade
Up connector of the next switch in the stack (shown in the simple two-switch stack connection
block diagram below):
1
2
3
Simplified Stacking diagram
1= Base unit
2= Last unit
3= Cascade/Stack Cable
To create a stack connection, order the appropriate ERS 4900 Series cascade cables to ensure
fail-safe stacking. For stacking three or more units (maximum eight units per stack),
order the cables as applicable (see other optional requirements).
1. Ensure that all switches for the stack are rack mounted.
2. Slide the Base Unit Select switches on the back of the units to the appropriate
position, depending on whether they are a base unit or non-base unit:
• Base Unit (Unit 1) - Slide the Base Unit Select switch DOWN.
• Non-Base Unit (Units 2-8) - Slide the Base Unit Select switch UP.
Because stack parameters are associated with the base unit, the physical stack
order depends on the base unit position and whether you configure the stack
cascade up (stack up) or cascade down (stack down). This designation depends
on the stack cabling arrangement.
IMPORTANT: Using a Cascade Down configuration is recommended.
Base
Switch
Unit 1
Unit 2
Unit 3