Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Scotsman MDT5N40A-1J
Summary of Contents for Scotsman MDT5N40A-1J
- Page 1 Installation and User's Manual for Ice Maker-Dispenser Models MDT5N25 and MDT5N40...
-
Page 2: Table Of Contents
MDT5N25 & MDT5N40 User Manual INTRODUCTION To the owner or user: This manual is intended to The ice dispensing section is a seamless plastic provide you, and the maintenance or service storage bin, with a stainless steel rotating vane to technician with the information needed to install, sweep the ice into the dispensing chute. -
Page 3: For The Installer: Specifications
Basic Cond. Ref. Charge, Minimum Circuit Maximum Electric Type R-404A in ounces* Ampacity Fuse Size H” x W” x D” MDT5N40A-1J 48.5 x 26 x 22.5 115/60/1 Air 19.3 MDT5N40W-1J same 115/60/1 Water 17 17.8 MDT5N40A-6J same 230/50/1 Air 11.5... -
Page 4: For The Installer: Environmental Limitations
CEILING and performance. They meet or exceed the standards of UL and NSF. CUT AWAY Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman SPACE that have been altered in any way, including the ABOVE... -
Page 5: For The Installer
Counter Top or Machine Stand Installation The base of the icemaker-dispenser must be sealed to the object it rests upon. Food grade silastic sealant such as Scotsman part number 19-0529-01 is recommended. Place a bead of the sealant on the machine stand... -
Page 6: For The Installer: Wall Mount Kit
MDT5N25 & MDT5N40 User Manual FOR THE INSTALLER: Wall Mount Kit CAUTION It is recommended that the wall mounting installation be done by an experienced contractor. The weight of the machine when in use may exceed 350 pounds. The unit should be mounted on a solid, rigid wall with proper fasteners for that type of wall and of adequate strength to support the weight of the machine when in use. -
Page 7: For The Plumber
MDT5N25 & MDT5N40 User Manual FOR THE PLUMBER CONFORM TO ALL APPLICABLE CODES Water Inlet Air Cooled Models: The recommended water supply is clean, cold water. Use 3/8" O.D. copper tubing, connect to the 3/8" male flare at the back of the cabinet. -
Page 8: For The Electrician
MDT5N25 & MDT5N40 User Manual FOR THE ELECTRICIAN CONFORM TO ALL APPLICABLE CODES The electrical power to the unit is supplied through the junction box at the INDIVIDUAL CIRCUIT rear of the machine. FOR ICE DISPENSER Check the nameplate (located on the back panel) for the voltage requirements, and for the minimum circuit ampacity. -
Page 9: For The Installer: Final Check List & Start Up
Water cooled models will begin to discharge warm water (110 F) down the 10. Fill out the Customer Evaluation and Warranty drain. Registration form, and mail it in to Scotsman. 5. The unit should soon be making ice. November 2008 Page 8... -
Page 10: Operation: Ice Vending
MDT5N25 & MDT5N40 User Manual OPERATION: Ice Vending Dispensing takes place when the Touch Free sensor’s infrared beam bounces back to the sensor from a container placed directly in front of ICE DISPENSING VANE If the container is in front of the Touch Free sensor on the left side, the ice dispensing vane will rotate and sweep ice over the ice... -
Page 11: Dispense Area Sanitation
MDT5N25 & MDT5N40 User Manual DISPENSE AREA SANITATION The dispense area; spouts, sink, grill and splash panel will need periodic cleaning and maintenance. 1. The ice chute may be pulled down to remove it from the ice dispenser. Wash and sanitize it. 2. -
Page 12: Cleaning And Sanitizing
MDT5N25 & MDT5N40 User Manual CLEANING and SANITIZING A Scotsman Ice System represents a sizable investment of time and money in any company’s business. In order to receive the best return for that investment, it MUST receive periodic maintenance. It is the USER’S RESPONSIBILITY to see that the unit is properly maintained. It is always preferable, and less costly in the long run, to avoid possible down time by keeping it clean;... -
Page 13: Maintenance And Cleaning
At least twice a year, If the bearing needs grease, inject grease into the the probe should be removed from the reservoir, bearing using Scotsman grease needle pn and the tip wiped clean of mineral build-up. 02-3559-01 and Scotsman bearing grease cartridge, pn A36808-001. -
Page 14: Service Diagnosis
MDT5N25 & MDT5N40 User Manual SERVICE DIAGNOSIS Symptom Possible Cause Probable Correction No ice made, nothing operates Unit off due to no power Restore power Unit off due to master switch in Switch master switch to ON OFF position Unit off due to low water level Check water supply, filter, strainer, float valve. -
Page 15: Service Diagnosis: Circuit Board
MDT5N25 & MDT5N40 User Manual SERVICE DIAGNOSIS: Circuit Board Explanation of Indicator Light Position On Name and Meaning of Board Light or Reset On at all times when the master switch is ON and machine is Power, connected to electrical power. ON = Normal On when ice level is low (unit making ice). - Page 16 SCOTSMAN ICE SYSTEMS 775 Corporate Woods Parkway, Vernon Hills, IL 60061 800-533-6006 www.scotsman-ice.com 17-3282-01...