Onkyo TX-NR929 Service Manual page 15

OPERATION CHECK-4
2.CONFIRMATIONS OF OPERATIONS
2-15. CONFIRMATION OF CEC OPERATION.
a. When TX-SR805 is used as CEC JIG.
1.When TX-SR805 is used as CEC JIG, this TX-SR805 JIG is set as follows.
2.After SETUP button is pushed, select next menu "Hardware Setup", "HDMI", "Control", "Enable".
3. HDMI Output(Main) of the set for inspection is connected with HDMI Input of the set for TX-SR805 JIG.
4. When the set for inspection is Power on, then change the state to "TEST 6-00".
5.FL is displayed "OK" or "NG".
b. When Panasonic TV (TH-20LX70) is used as CEC JIG.
1.HDMIOutput(Main) of the inspection is connected with Panasonic TV(TH-20LX70).
2. When the set for inspection is Power on, then change the state to "TEST 6-00".
3.FL is displayed "OK" or "NG".
2-16. COMFIRMATION OF NETWORK
1. PC and the set are connected through the router.
2.When set to TEST 3-18 confirm that the display of AVR change IP adress.
*Please wait for about 20 seconds after turning on the power supply of the set when you use from TEST 3-18.
3.Change the state to "TEST 3-09"(Front) ".
4.When Connect USB storage to AVR USB front port ,
confirm this USB storage is shown on FL display and HDMI main out of AVR .
5.Confirm the audio signal is output, when TEST MODE is set from TEST 3-11 to TEST 3-17.
(Confirm at Zone2 Preout/Line out terminal.)
2-17. CONFIRMATION OF Zone2 HDMI SIGNAL. *CONNECT HDBaseT RX box to AVR(DTR-60.5(exceptMJJ),DHC-60.5)
1. When TEST 5-14, confirm the sound outputs of HDMI IN4 input from the Powered Zone2 speakers(except DHC-60.5).
When TEST 5-14, confirm the sound outputs of HDMI IN4 input from Zone2 PRE/LINE OUT(only DHC-60.5).
And confirm the HDMI video and audio output of HDMI IN4 input from the TV connected OUT Zone2 HDMI terminal.
2. WAfter set to the "TEST 6-13", confirm that LED of HDMI Zone2 CEC JIG does not shine.JIG use is carried out and it inspects.
3.After set to the "TEST 6-12", confirm that LED of HDMI Zone2 CEC JIG shines. JIG use is carried out and it inspects.
4.When 6-15, The check of Zone2 HDMI CEC of operation. FL is displayed "OK" or "NG".JIG use is carried out and it inspects.
HDMI IN1
a. When TX-SR805 is used as CEC JIG.
1.When TX-SR805 is used as CEC JIG, this TX-SR805 JIG is set as follows.
2.After SETUP button is pushed, select next menu "Hardware Setup", "HDMI", "Control", "Enable".
3. HDMI Output(Main) of the set for inspection is connected with HDMI Input of the set for TX-SR805 JIG.
4. When the set for inspection is Power on, then change the state to "TEST 6-15".
5.FL is displayed "OK" or "NG".
b. When Panasonic TV (TH-20LX70) is used as CEC JIG.
1.HDMIOutput(Main) of the inspection is connected with Panasonic TV(TH-20LX70).
2. When the set for inspection is Power on, then change the state to "TEST 6-15".
3.FL is displayed "OK" or "NG".
HDMI IN2 HDMI IN3 HDMI Front
TX-NR929/ DTR-60.5/ DHC-60.5
HDMI
Main OUT