DC connections and result in a fire. ► Always take into account the maximum cur- rent of the DC connections when planning the installation. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Check the delivery for completeness and all com- ponents for damage before starting installation work. Do not use any damaged components. Keep the packaging. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
The inverter must not be disposed of as standard household waste, but in accordance with the applicable elec- tronic waste disposal regulations of your country or region. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
For example, the power of the inverter will be reduced if it is too heavily heated by solar radiation. This is normal operat- ing behavior for the inverter and is necessary to protect the internal electronics. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
1. Attach the mounting plate to the wall / the mounting system with 8 M6 screws. 2. Mount the inverter on the mounting plate. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 11
Two voltage sources Prior to any work, disconnect 3 Washer - Distribution network both sources 4 Spring washer - PV modules 5 M4 screw Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Allowed Requirements for the grid voltage 3P3W Voltage 3P4W Voltage L1-L2 400 V ±20 % L1-N 230 V ±20 % Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 13
3 = L3 4 = N Connecting to a 3-phase grid without a neutral conductor (3P3W) 2 = L2 1 = L1 3 = L3 Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 14
3. Fit and crimp the wire end sleeves to the ends of the wires. 4. Unscrew the nut and housing from the AC plug. 7. Fit the housing and nut and screw the nut tight. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 15
10. If the inverter is connected to a grid without a neutral con- ductor, the AC connection type must be changed using the display to 3P3W after commissioning, see “AC connection type”, page 23. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
3. Plug the DC plugs with the DC cables into the DC connec- tions on the inverter. → The installation should look like the following illustration. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 17
5.5-9 32.0017P0001-UR 1) Included in the scope of delivery of the M6A / M8A 2) Included in the scope of delivery of the M10A Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Termination resistor = ON 1 RS485 (terminal block) 2 DIP switch for the RS485 termination resistor DIP switch for the RS485 termination resistor RS485 Data logger Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 19
► Set a different inverter ID at each inverter during commis- sioning of the inverters. Termination resistor = ON Termination resistor = OFF Termination resistor = OFF RS485 Data logger Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
V1 + K5 Reserved V1 + K6 Reserved After commissioning, the relays can be defined as make-contact or break-contact for the external shutdown on the display. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
M a x . P o w e r : 8 8 0 0 0 W R e t u r n t o F a c t o r y Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
R e t u r n t o F a c t o r y Use the buttons to configure a value and then press the button. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
See “Connecting the digital inputs, dry contacts and external power-off (optional)”, F a n F a i l page 20 for the available options. I n s u l a t i o n Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Total harmonic distortion (THD) < 3% at rated apparent power DC injection < 0.5% at rated current Power loss in night mode < 2 W Overvoltage category Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...
Page 27
Limited to 4.99 kVA, when grid type AU/NZ PL 4.99k is selected. AC voltage and frequency range are programmed using the corresponding country specifications. Quick installation guide for solar inverters RPI M6A M8A M10A EU V4 EN 5013221703 00 2017-11-16...