Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Neilsen Manuals
  4. Spreader
  5. CT2207
  6. Original manual

Neilsen CT2207 Original Manual

60lb walk-behind spreader
Hide thumbs Also See for CT2207:

Advertisement

Quick Links

Download this manual See also: User Manual
60LB WALK-BEHIND SPREADER CT2207
ORIGINAL MANUAL
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Advertisement

loading

Related Manuals for Neilsen CT2207

Summary of Contents for Neilsen CT2207

  • Page 1 60LB WALK-BEHIND SPREADER CT2207 ORIGINAL MANUAL SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
  • Page 2 In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: WALK-BEHIND SPREADER Model: CT2207 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 12100, EN 349, EN 953, EN ISO 13857 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
  • Page 3 IMPORTANT INSTRUCTIONS 1. HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY WHEN ALL ELSE FAILS, READ THE DIRECTIONS AGAIN If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must turn clockwise. Reversing the gear box will cause the impeller to turn counter clockwise.
  • Page 4 3. ASSEMBLY INSTRUCTIONS STEP 1. Install impeller onto the Gear Box & Axle Assembly. Insert Screw M4x20 through impeller then through Gear Box Axle.
  • Page 5 STEP 2. Insert the support leg into the hole of the Support Leg Assembly, then insert 4 pieces of Hex Bolt M6x45 to each hole on the Support Leg Assembly. STEP 3: 1. Connect the Wheel Assembly Frame and Support Leg by inserting the Hex Bolts. 2.
  • Page 6 STEP 4: 1. Attach the Wheel Assembly Frame on each side of the Gear Box Axle. 2. Make sure the hole on Axle of Gear Box is to be on the right side when assembly as shown. Tighten all the bolts and nuts. 3.
  • Page 7 STEP 5: 1: Insert the Hopper into the Axle of Gear Box. 2: Insert 4pcs Bolt M6X35 into the holes in the bottom of the hopper with 4 flat washers bolts through the holes on the Wheel Assembly Frame. locked by 4pcs lock nut M6.
  • Page 8 STEP 6: Connect the Gauge and Handle Assembly by inserting the Hex Bolt M6x30 and Lock Nut M6. STEP 7: Connect the Handle Assembly and the Support leg by inserting the Carriage Bolt.
  • Page 9 STEP 8: ADJUSTABLE. When you finished all above steps, if you find the three big holes at the bottom of hopper just match the three holes of adjustable plate. You don't need to do the following steps. If they are not match neatly, you may need to do the following steps. (1)Release two bolts M5x10 on clamp as shown.

  • Page 10: Operating Instructions

    OPERATING INSTRUCTIONS Before filling hopper, become familiar with the operation of this spreader. 1- Move stop bolt on rate gauge assembly to the proper setting. 2- While pushing spreader forward, pull control lever back to stop bolts. 3- Top stop, push lever forward to close flow holes before you stop moving. 4- When finished, empty any remaining material from hopper.
  • Page 11 PARTS DRAWING...

  • Page 12: Parts List

    PARTS LIST Ref# Description Ref# Description Carriage Bolt M6x25 Lock Nut M6 Outside Teeth Lock Washer Ø8 Support Leg Gauge and Lever Assembly Cotter Pin Ø5x45 Adjust Handle Pole Thin Washer Adjust Handle A Plastic Wheel Adjust Handle B Tube Cover Ø30 Screw ST4x18 Wheel Axle Handle Grip...