Related Manuals for Neilsen CT2206
Summary of Contents for Neilsen CT2206
- Page 1 100LB WALK BEHIND SPREADER CT2206 Instruction & Assembly SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE...
- Page 2 In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: WALK BEHIND SPREADER Model: CT2206 Applicable EC Directives: EC Machinery Directive 2006/42/EC 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
-
Page 3: Table Of Contents
Table of Contents General Warnings and Rules ................3 Hazard Signal Word Definitions ................4 Controls and Features Identification ..............5 Component & Hardware ..................6 Assembly Instructions ................7, 8, 9 10 Operation Instructions ................... 11, 12 Spreading Instructions ..................13 Maintenance and Storage ................... - Page 4 GENERAL WARNINGS READ and UNDERSTAND this manual completely before using Push Spreader. Operator must read and understand all safety and warning information, operating instructions, maintenance and storage instructions before operating this equipment. Failure to properly operate and maintain the push spreader could result in serious injury to the operator or bystanders. Operation Warnings Do not at any time carry passengers sit or stand on the spreader.
-
Page 5: Hazard Signal Word Definitions
Hazard Signal Word Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates an imminently hazardous DANGER situation which, if not avoided, will result in death or serious injury. -
Page 6: Controls And Features Identification
Controls and Features Identification Read this owner’s manual before operating the equipment. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 1) Handle – Pushes and moves the spreader easily. 2) Flow Control – Controls the flow of material being spread. 3) Hopper –... - Page 7 CAUTION Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment could result in serious injury to the user or bystanders, or cause equipment damage. PUSH SPREADER COMPONENT PARTS AND ASSEMBLE. Take all parts out of the shipping crate and inspect components to ensure there are no missing pieces before starting to assemble the push spreader follow steps 1 through 8.
-
Page 8: Assembly Instructions
Assembly Instructions STEP 1: Install impeller onto the Gear Box 1. Insert Screw M4x20 through impeller then through gear box axle . STEP 2: Install Wheel Assembly Frame on the Gear Box 1. Make sure the hole on axle of gear box is on the right side of the assembly as shown below. Attach one end of frame brace to hopper frame assembly using bolts M6x35 and lock nuts M6. - Page 9 STEP 3: Insert Inner Axle Bushing into Outer Axle Bushing 1. Make sure everything has been tightened. Install the right tire assembly to right axle using bolt M5x45 and lock nut M5, and then install nylon washer and end cap onto right axle using a wooden or rubber hammer.
- Page 10 STEP 5: Installing Gauge and Handle 1. Upper handle has three positions for operator comfort before installing the gauge operator needs to determine the best. 2. Insert bolt M6X50 through both upper handles, flat washer and loosely tighten the M6 lock nut. 3.
- Page 11 STEP 7: Installing Control Rod 1. Push the handle gauge to the lowest position and insert the upper end of control rod into the hole on the adjustable handle. 2. Remove one of nuts from threaded pole and insert the nut through the hole of pivot & bracket and threaded pole and tighten.
-
Page 12: Operation Instructions
Operation Instructions WARNING Before using the push spreader, review the instructions below and safety information before operating. Failure to follow these instructions may result in property damage or injury to the operator or bystanders . USING YOUR SPREADER 1. Inspect your spreader before each use. Make sure the wheels turn easily, and the gearbox moves when the spreader is pushed. -
Page 13: Operation Instructions
Operation Instructions ADJUSTING THE FLOW 1. Push the handle to the top position (upwards). Move the position of the wing nut on the gauge & lever to adjust the three holes between hopper and adjustable plate when spreading material. CONSISTENT COVERAGE To insure consistent coverage, make sure each broadcast pattern slightly overlaps the previous broadcast pattern as shown in figure below for large particles. -
Page 14: Spreading Instructions
SPREADING INSTRUCTIONS CALCULATING AMOUNT OF MATERIAL NEEDED To calculate the amount of fertilizer you will need to cover your lawn, divide the coverage amount listed on the label by the weight of the fertilizer bag. For example a 10LB. bag of fertilizer with coverage of 10,000 square feet will distribute 1LB. -
Page 15: Maintenance And Storage
Maintenance and Storage WARNING Improper maintenance and storage of the push spreader may void your warranty. MAINTENANCE • After each use clean material out of hopper. • Rinse/dry inside and outside of the spreader after each use. • Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE 25 PSI. •... -
Page 16: Specification
Specifications Load Capacity ....................100lb Spreader Type ..................Broadcast Hopper Material ................Polypropylene Hopper Dimensions ..............21.5” x 21.5”x14” Overall Dimensions ..............48.8”x32.1”x21.7” Wheel size ....................... 12.5” Tire Pressure (PSI) ....................25 Unit Weight ....................25.35lb The manufacturer reserves the right to make improvements in design and/or changes in specifications at any time without incurring any obligation to install them on units previously sold. -
Page 17: Parts Drawing & Parts List
Parts Drawing & Parts List - 17 -... - Page 18 Ref# Drawing No. Description N572-00003 Handle Spacer 9114-06025-DG Carriage Bolt M6x25 9315-08000-DG Teeth Lock Washer Ø8 N570-10000 Gauge & Lever Assembly N570-00001-DG Adjustable Handle Pole N570-00014 Adjustable Handle A N570-00015 Adjustable Handle B 9118-04018-DG Screw M4x18 N510-00016 Spacer N510-00019 Wing Nut M6 9101-06045-DG Hex Bolt M6x45 C130-00004...
- Page 19 Ref# Drawing No. Description N570-00023 Shut off plate 9302-04000-DG Big Flat Washer Ø4 9118-04012-DG Screw M4x12 N572-00005 Hopper Assembly Frame N570-00010-DG Frame Brace 9101-06050-DG Hex Bolt M6X50 9101-06035-DG Hex Bolt M6X35 9301-16000-DG Flat Washer Ø16 N511-40000-BXG End Cap N570-00020 Tire N570-00018 Inner Bushing N570-00011...
- Page 20 CANNON TOOLS LTD 20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K. Made in China - 20 -...