4.1 Dealing with lithium batteries..................... 22 Starting up..............................24 Connections and controls........................26 Operating..............................32 7.1 Starting the device........................... 32 7.2 Operating on the unit........................32 7.3 IR remote control..........................35 7.4 Menu overview..........................36 BAT.PAR 144 RGBW LED spotlight...
Page 4
7.6 Functions in 4-channel DMX mode................... 37 7.7 Functions in 6-channel DMX mode................... 38 7.8 Functions in 7-channel DMX mode................... 39 Technical specifications........................41 Plug and connection assignments....................42 Troubleshooting............................43 Cleaning............................... 45 Protecting the environment......................46 BAT.PAR 144 RGBW LED spotlight...
If you sell the unit please make sure that the buyer also receives this manual. Our products are subject to a process of continuous development. Thus, they are subject to change. BAT.PAR 144 RGBW LED spotlight...
Our online guides provide detailed information on technical basics Online guides and terms. Personal consultation For personal consultation please contact our technical hotline. If you have any problems with the device the customer service will Service gladly assist you. BAT.PAR 144 RGBW LED spotlight...
The letterings for connectors and controls are marked by square brackets and italics. Examples: [VOLUME] control, [Mono] button. 1.3 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this manual. BAT.PAR 144 RGBW LED spotlight...
Page 9
This combination of symbol and signal word indicates a pos- sible dangerous situation that can result in material and environmental damage if it is not avoided. Warning signs Type of danger Warning – high-voltage. Warning – suspended load. BAT.PAR 144 RGBW LED spotlight...
Page 10
General information Warning signs Type of danger Warning – danger zone. BAT.PAR 144 RGBW LED spotlight...
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety. BAT.PAR 144 RGBW LED spotlight...
Page 12
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged. BAT.PAR 144 RGBW LED spotlight...
Page 13
Eye damage caused by high light intensity Never look directly into the light source. WARNING! Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights. BAT.PAR 144 RGBW LED spotlight...
Page 14
Follow the advice on the correct handling of lithium batteries in the present sec- tion. NOTICE! Risk of fire Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked flames. BAT.PAR 144 RGBW LED spotlight...
Page 15
Failure to do so could result in damage to the device and possibly injure the user. Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire. BAT.PAR 144 RGBW LED spotlight...
Page 16
Ensure that proper polarity is observed when inserting batteries. NOTICE! Possible damage by leaking batteries Leaking batteries can cause permanent damage to the device. Take batteries out of the device if it is not going to be used for a longer period. BAT.PAR 144 RGBW LED spotlight...
Page 17
Store the equipment at a tempera- ture between 10 °C and 32 °C in as dry an environment as possible. During extended storage periods, charge the batteries to 50 % approximately every three months. BAT.PAR 144 RGBW LED spotlight...
Stand-alone operation with static colours Sound control Battery or mains powered Power adapter and infrared remote control included Suitable for use in clubs, bars, theatres, exhibitions, etc. or for mobile use BAT.PAR 144 RGBW LED spotlight...
Risk of injury caused by falling objects Make sure that the installation complies with the standards and rules that apply in your country. Always secure the device with a secondary safety attachment, such as a safety cable or a safety chain. BAT.PAR 144 RGBW LED spotlight...
Page 20
When mounting the device onto a stand, ensure that the stand is in a safe and stable position and that the weight of the device does not exceed the maximum permissible load capacity of the stand. BAT.PAR 144 RGBW LED spotlight...
Page 21
Always work from a stable platform whenever installing, moving or servicing the unit. In doing so, the area underneath the unit must be cordoned off. The safety-rope must be attached to the bracket. BAT.PAR 144 RGBW LED spotlight...
In the event of a short circuit, overheating or mechanical damage, lithium bat- teries can cause severe injuries. Follow the advice on the correct handling of lithium batteries in the present sec- tion. When handled correctly and appropriately lithium batteries pose no risk. BAT.PAR 144 RGBW LED spotlight...
Page 23
Before disposing of the device remove the lithium batteries. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape. Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning lithium battery. BAT.PAR 144 RGBW LED spotlight...
Starting up Starting up Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards. BAT.PAR 144 RGBW LED spotlight...
Page 25
Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 Ω, ¼ W). BAT.PAR 144 RGBW LED spotlight...
Connections and controls Connections and controls BAT.PAR 144 RGBW LED spotlight...
Page 27
Selects an option of the respective operating mode, confirms the set value. 2 Locking screws for the mounting bracket. 3 Bracket for floor placement or hanging. 4 [POWER] Connection socket for the 15 V power supply unit. 5 Rechargeable battery compartment. BAT.PAR 144 RGBW LED spotlight...
Page 28
Remaining battery capacity display. When all the LEDs are on, the battery is fully charged. If only the red LED is on, the unit must be connected to the mains again to charge as soon as possible. 8 [DMX IN] DMX input. 9 [DMX OUT] DMX output. BAT.PAR 144 RGBW LED spotlight...
Page 29
Connections and controls Remote control BAT.PAR 144 RGBW LED spotlight...
Page 30
14 [UP], [DOWN] Buttons to switch between programmes and to increase / decrease numeric values. 15 Buttons for colour selection. [W] for white light. [R], [G] or [B] for primary colours red, green and blue. BAT.PAR 144 RGBW LED spotlight...
Page 31
Connections and controls 16 [STROBE] Button to turn the strobe effect on or off. 17 Numeric buttons 0 … 9 for direct value input. 18 [SOUND 1], [SOUND 2] Buttons to activate sound-control mode 1 or 2. BAT.PAR 144 RGBW LED spotlight...
Use [UP] and [DOWN] to select a value between 1 and 512 (the display shows ‘A001’ … ‘A512’ ). Confirm with [ENTER]. Make sure that this number matches the configuration of your DMX controller. Sound control Press [MENU], [UP] or [DOWN] repeatedly until the display shows ‘Soun’ . Confirm with [ENTER]. BAT.PAR 144 RGBW LED spotlight...
Page 33
Use [UP] and [DOWN] to select a constant colour in a range from ‘Col1’ … ‘Col51’ . Confirm with [ENTER] Operating mode Auto Press [MENU], [UP] or [DOWN] repeatedly until the display shows ‘Auto’ . Confirm with [ENTER]. BAT.PAR 144 RGBW LED spotlight...
Page 34
The display shows ‘Sla’ , the unit is now in Slave mode. DMX mode Press [MENU], [UP] or [DOWN] repeatedly until the display shows ‘Chnd’ . Confirm with [ENTER]. With [UP] or [DOWN] you can now select one of the following DMX modes: BAT.PAR 144 RGBW LED spotlight...
7.3 IR remote control Press [MENU], [UP] or [DOWN] repeatedly until the display shows ‘reno’ . Confirm with [ENTER]. Use [UP] and [DOWN] to select the option ‘on’ to enable IR remote control. Confirm with [ENTER]. BAT.PAR 144 RGBW LED spotlight...
Channel Value Function 0…255 Intensity red (0 % to 100 %) 0…255 Intensity green (0 % to 100 %) 0…255 Intensity blue (0 % to 100 %) 0…255 Intensity white (0 % to 100 %) BAT.PAR 144 RGBW LED spotlight...
Intensity red (0 % to 100 %) 0…255 Intensity green (0 % to 100 %) 0…255 Intensity blue (0 % to 100 %) 0…255 Intensity white (0 % to 100 %) 0…255 Stroboscope effect (0 % to 100 %) BAT.PAR 144 RGBW LED spotlight...
(lithium ion battery, 10.8 V, 1500 mAh) Power consumption 20 W Operating time per battery approx. 5 h charge Dimensions (W × H × D) 250 mm × 254 mm × 134 mm Weight 2 kg BAT.PAR 144 RGBW LED spotlight...
The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug. Configuration Ground, shielding Signal inverted (DMX–, ‘cold signal’) Signal (DMX+, ‘hot signal’) BAT.PAR 144 RGBW LED spotlight...
Never connect the DMX input or output to audio devices such as mixers or ampli- fiers. In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting: BAT.PAR 144 RGBW LED spotlight...
Page 44
Do not attempt to replace the built-in battery yourself. be recharged Please contact our service centre. If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. BAT.PAR 144 RGBW LED spotlight...
The fan grids of the device must be cleaned on a regular basis to remove dust and dirt. Before cleaning, switch off the device and disconnect AC-powered devices from the mains. Use a lint- free damp cloth for cleaning. Never use solvents or alcohol for cleaning. BAT.PAR 144 RGBW LED spotlight...
They should be returned to the manufacturer for disposal or recycled elsewhere in accordance with your local regulations. Remove lithium batteries from the device before disposal. Protect used lithium batteries against short circuit, for example by taping the poles. BAT.PAR 144 RGBW LED spotlight...
Page 47
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. BAT.PAR 144 RGBW LED spotlight...