Page 1
MyWirelessTV3 4K Wireless HD Connection Kit Model#: MWTV3TX & MWTV3RX Serial Model Name: MWTV3KIT User Manual V0.01 Applied to 4K Wireless HD Connection Kit MyWirelessTV3 Wireless HD Transmitter MyWirelessTV3 Wireless HD Receiver...
Table of Contents Part I. Introduction ..........................1 1.1. Minimum System Requirements .................... 1 1.2. Package Contents ........................1 1.3. Getting To Know MyWirelessTV 3 ..................1 1.3.1. MyWirelessTV 3 Transmitter ..................1 1.3.2. MyWirelessTV 3 Receiver .................... 3 Part II. Connecting MyWirelessTV 3 ...................... 5 2.1.
Page 3
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part I. Introduction Thank you for purchasing MyWirelessTV 3. This product will allow you to transmit high-definition content from a set top box, gaming console, or other source with an HDMI port, to an HDTV monitor in another location, without lag or picture quality loss. It allows you to view movies and television programs in two different locations at the same time, without wires, or play a game on a television in one room, while the gaming console resides in another.
Page 5
LINK LED. The LINK LED isused to display the state of pairing between the Transmitterand Receiver. If it is blinking or off, the Transmitter is not paired with any Receiver. If it is glowing steadily, it has paired witha Receiver. SELECT button.
firmware update is available. See "错误!未找到引用源。" for more details. Power port. The 5V DC / 2A power portisused to connect the Transmitter to a power source. HDMI Input port. The HDMI Input port is used, via an HDMI cable, to connect the ...
Page 7
LINK LED. The LINK LED isused to display the state of pairing between the Transmitterand Receiver. If it is blinking or off, the Transmitter is not paired with any Receiver. If it is glowing steadily, it has paired witha Receiver. POWER LED.
Part II. Connecting MyWirelessTV 3 Connecting MyWirelessTV consists of two parts: connecting theTransmitter to a source of high-definition video, and connecting thereceiver to a high-definition television monitor. This chapter will take youthrough both procedures, as well as setting up the IR Blaster and IRReceiver to allow you to use the remote control of the source device in thelocation you are watching (or playing) your content.
2.2. Connecting the MyWirelessTV Transmitter You should install the Transmitter near the video source device (settop box, Blu-ray player, gaming console, etc.). Follow the procedure below to set up the MyWirelessTV transmitter: Select the source device (i.e. a Cable/Satellite set-top box or Blu-ray player) you wish to transmit signal to the TV, and power off that device.
Plug oneend of the HDMI cable into an HDMI port on the HDTV monitor. Plug the other end of the HDMI cable into the HDMI OuttoTV port on the Receiver. Plug the connector of the power cord into the 5VDC / 2Aport on the Receiver.And plug the AC adapterof the power supply into a power outlet.
Page 11
Plug theIR Receiver ExtensionCable's green connector into the green IR Ext port on the Receiver. Remove the protective covering of the double-stick tape and attach theflat end of the IR Receiver ExtensionCable to the front corner of the HDTVmonitor's bezel or frame. You should now be able to use the remote control of the source devicefrom the location of the HDTV monitor to which you are streamingcontent.
Appendix I. Specifications This chapter lists the specifications of the MyWirelessTV 3devices. Video: H.264 video compression Supports up to 3840*2160@60fps in oneTx to one Rx setup Audio: Non-compressed LPCM Pass-through 5.1 surround A/V interface: Transmitter: One HDMI input &one HDMI pass-through ...
Page 13
Regulatory and compliance: Warranty: One (1) year limited Draft...