Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu-

facturer.

Welcome to your new vehicle

0.1

Table of Contents

Chapters

Table of Contents

Summary of Contents for Renault Captur

Page 1 It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains about the vehicle and its functions and new features. If certain points are still unclear, our Renault authorisesd dealers will be pleased to provide you with any additional information.
Page 3: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 5 The RENAULT card: general information and use ........
Page 6: Battery Life
3 Switch on courtesy light remotely. surroundings:when handling RISK OF DEATH OR SERIOUS 4 Integrated key. RENAULT card, it is important to make INJURY sure that you do not lock/unlock the 5 Locking/unlocking tail gate. doors by inadvertently pressing the but- When the battery of the card is flat, you tons.
Page 7: Using The Key
RENAULT CARD:GENERAL INFORMATION (2/2) Using the key This RENAULT card is used to start the engine by Please refer to the information - inserting the card into the card on,”Locking and unlocking the opening reader/placing the card in the passeng- elements”.
Page 8: Remote Control Renault Card: Use
If a door or the luggage compartment is open Renault card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and luggage compartment lock then quickly...
Page 9: Hands Free Renault Card: Use
HANDS FREE RENAULT CARD: USE (1/3) Unlocking the vehicle On equipped vehicles, in addition to With the RENAULT card in zone 1 and the functions of the remote control the vehicle locked, press button 3 on RENAULT card, it can be used to lock/...
Page 10: Locking The Vehicle
With the doors and tail gate closed, press 3 on one of the front door han- dles. The vehicle will lock. Note: a RENAULT card must be within the vehicle’s access zone (zone 1) to be able to lock the vehicle using the button.
Page 11 HANDS FREE RENAULT CARD: USE (3/3) “Hands-free” RENAULT card nond- tection alarm With the engine running, if you open and close a door and the card is no longer within range 6, the message “Keycard not detected” and a beep warns you of this.
Page 12 Opening the doors from outside inside. With the doors unlocked, pull handle 2. Pull handle 3. Special feature of RENAULT hands- free card Lights ON reminder buzzer With the doors locked, press button 1 If you have switched off the ignition...
Page 13: Opening And Closing The Doors
OPENING/CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle. Never leave an animal, child or adult who is not self suffi- cient alone in your vehicle,even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as elec- tric windows or locking doors.
Page 14 Section 1. In certain cases, the RENAULT card may not work, or its access area will be modified: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used;...
Page 15 Unlocking the vehicle from the outside possible to open the doors from inside is only possible with the RENAULT card using door handle during emergency in the vehicle's access zone or using conditions without pressing switch 4.
Page 16: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the function With the engine running, press the button 1 for approximately 5 seconds, until you hear a warning beep. Operating faults If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the open- ing elements, etc.), firstly check that the opening elements are properly closed.
Page 17: Rear View Mirrors
REAR VIEW MIRRORS Folding door mirrors (depending on vehicle) Turn knob 1 to position D to fold the door mirrors 2. To reset them for driv- ing, return to position B. If the door mirrors are folded manually, turn the knob 1 to position D and then to position B to reset.
Page 18: Front Headrests
FRONT HEADRESTS To remove the headrest Raise the headrest to its highest posi- tion (tilt the seatback backwards if ne- cessary). Press button 1 and lift the headrest to release it. To refit the headrest Insert the headrest rods into the holes (tilt the seatback backwards if neces- sary).
Page 19: Front Seats
FRONT SEATS To move forwards or backwards Make sure that the seat- - Lift handle 3 to unlock and move the. backs are correctly locked seat. in place. - Release the handle once the seat is in the desired position and ensure that the seat is locked.
Page 20: Seat Belts
SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 21 SEAT BELTS (2/4) Seat belt reminder warning ß light It lights up on the central display when the engine is started then, if the driv- er’s seat belt is not fastened, the light flashes and a beep sounds for about 2 minutes when the vehicle reaches a speed of approximately (12.4 mph) 20 km/h.
Page 22 SEAT BELTS (3/4) Rear side seat belts Rear centre seat belt Fastening the belt in the (depending on vehicle) Slowly unwind belt 7 and click buckle 9 centre seat may be diffi- into red catch 8. Fasten sliding buckle 10 into red cult when the 1/3 section of catch 11.
Page 23 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 24: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they will – Have the entire restraint consist of: system checked following – seat belt inertia reel pretensio- an accident. ners; – No operation whatsoe- –...
Page 25 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Airbags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
Page 26 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation Operating faults This system is only operational when å Warning light 4 will light up on the ignition is switched on. the instrument panel when the ignition In a severe frontal impact, the air bags is turned on and then go out after a few inflate rapidly, cushioning the impact seconds.
Page 27 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 28: Side Protection Devices
SIDE PROTECTION DEVICES Side Airbags These airbags may be fitted to the front Depending on the vehicle, a marking on the windscreen informs you of the pres- seats and are deployed at the sides of ence of additional means of restraint (air bags, pretensioners, etc.) in the pas- the seats (door side) to protect the oc- senger compartment.
Page 29: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
Page 30: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 31 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 32 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 33: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/3) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
Page 34 CHILD SAFETY: choosing a child seat mounting (2/3) The two rings 1 and 2 are located be- Before installing an ISOFIX seat Note: if you remove the ISOFIX seat, tween the seatback and the seat base in the rear at the side, please ensure remember to take out and reposition of the seat and are identified by a mark- that you have retracted the seat belt...
Page 35 CHILD SAFETY: choosing a child seat mounting (3/3) The third ring 5 is used to attach the upper strap on some child seats. The 4 belt should be positioned be- tween the seatback and the rear parcel shelf. To do this, remove the rear parcel shelf (refer to the information on the “Rear parcel shelf”...
Page 36: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat: general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, when this child seats. The diagrams on the fol- is possible, you can move the vehi- The laws concerning children travel- lowing pages show you how to attach cle seat forward if necessary (so as to...
Page 37 CHILD SAFETY: fitting a child seat: general information (2/2) In the rear side seat Always remove the headrest from the Rear centre seat rear seat used for the child seat (see A carrycot can be installed across the A child seat may only be fitted in this “Rear headrests”...
Page 38: Child Seats: Attachment By The Seat Belt
CHILD SEATS: attachment by the seat belt (1/3) The table below summarises the information already shown on the diagram on the following pages, to ensure the ap- plicable regulations are respected. Front passenger Type of child seat Weight of the child Rear side seats Rear centre seat seat (1)
Page 39 CHILD SEATS: attachment by the seat belt (2/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 40 CHILD SEATS: attachment by the seat belt (3/3) Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child.
Page 41 CHILD SEATS: attachment using the ISOFIX system (1/3) Child seat fitted using the ISOFIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
Page 42 CHILD SEATS: attachment using the ISOFIX system (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Five-seater version Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats Rear centre seat...
Page 43 CHILD SEATS: attachment using the ISOFIX system (3/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. (1) If necessary, position the vehicle seat as far back as possible.
Page 44: Driving Position: Right-Hand Drive
DRIVING POSITION, RIGHT-HAND DRIVE (1/2) 1.40...
Page 45 DRIVING POSITION, RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Left side air vent -. 11 Right side air vent -. 21 Gear knob. 2 Tweeter. 12 Cruise control/Speed lock switch. 22 Gear lever. 3 Location for passenger airbag.
Page 46: Steering Wheel/Power-Assisted Steering
STEERING WHEEL/POWER-ASSISTED STEERING Power Assisted Steering For safety reasons, only With the engine running, do not leave adjust the steering wheel the steering wheel at full lock while sta- when the vehicle is station- tionary as this may damage the power- ary.
Page 47 INSTRUMENT PANEL(1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Main beam headlight tell-tale á light Dipped beam headlight tell- tale light Front fog light tell-tale light Rear fog light tell-tale light Left-hand direction indicator tell-tale light Right-hand direction indica- tor tell-tale light...
Page 48: Warning Lights
INSTRUMENT PANEL(2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Air bag warning light Toxic Fume Filter System å Ä Warning Light This comes on when the igni- tion is switched on and goes out after a This lights up when the ignition is few seconds.
Page 49 INSTRUMENT PANEL(3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Battery charge warning light Hand brake on and brake Ú circuit fault warning light This comes when ignition is ON and goes out after few sec- comes when ignition...
Page 50: Displays And Indicators
DISPLAYS AND INDICATORS Rev counter 1 Low engine oil level warning (graduations x 1000) When the engine is started, display 2 alerts the driver when the oil level is at Driving style indicator 3 its minimum. Refer to the information on the “Engine oil level”...
Page 51 ON-BOARD COMPUTER: general information (1/2) f) distance travelled; g) average speed; j) clock and temperature; On-board computer 1 Display selection keys 2 and 3 Depending on the vehicle, this includes the following functions: Scroll through the following information upwards (key 2) or downwards (key 3) –...
Page 52 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 53 ON-BOARD COMPUTER (1/2) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT and COUNTRY. Interpreting the display selected DISPLAY Total distance recorder/Trip distance recorder Fuel used (Fuel consumed since last reset) Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset.
Page 54 ON-BOARD COMPUTER (2/2) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT and COUNTRY. Interpreting the display selected DISPLAY Estimated range with remaining fuel. This value is displayed after driving approximately 400 metres. Distance travelled since last reset. Average speed since last reset.
Page 55: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE (1/2) 9°C 12:00 Display A Wait a few seconds, the minutes will flash: repeatedly press or press and To access the display 2 for setting the hold button 3 or 4 to set the time. time, press button 3 or 4 on the stalk 1. When setting is complete, the hours Wait a few seconds;...
Page 56 CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator Special note: When the exterior temperature is betw- een -3°C to + 3°C, the °C characters flash (signalling a risk of ice on the road). Display B Vehicles fitted with touch-screen multimedia, navigation aid systems, telephones, etc.
Page 57: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/4) Daytime running lights Side lights Position function in headlamp is disa- š bled and the same is integrated in the function Turn the ring 2 until the symbol Day light running light A, when the ring (front lights only) is opposite mark 3.
Page 58 EXTERIOR LIGHTING AND SIGNALS (2/4) Dipped beam headlights Manual operation Turn the ring 2 until the symbol is oppo- site mark 3. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) Turn ring 2 until the AUTO symbol is op- posite mark 3: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
Page 59 EXTERIOR LIGHTING AND SIGNALS (3/4) Switching off the lights “Follow-me-home lighting” function There are two possibilities: – manually, move ring 2 to position 0; This function allows you to briefly switch – the lights will go out automatically on the dipped beam headlights (to pro- when the engine is switched off, the vide light when opening a gate, etc.).
Page 60: Rear Fog Light
EXTERIOR LIGHTING AND SIGNALS (4/4) Cornering lights function Turning off the fog lights Whenever the dipped beam headlights There are two possibilities: are on and under certain conditions (at – manually, depending on the vehicle, speed, the steering wheel at an angle, turn centre ring 4 again until mark 5 in forward gear, the indicator lights on, is opposite the symbol for the fog...
Page 61: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 62: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) For manual settings Examples of positions for adjusting control A according to the load Criteria Driver alone or with front passenger Driver with one front passenger and three rear passengers On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the vehicle’s Driver with one front passenger,...
Page 63 HEADLIGHT BEAM ADJUSTMENT (2/2) Temporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors. For each headlight, using a screw- driver, turn the screw 1 by a quarter turn towards the - symbol to lower the beams.
Page 64 WIND SCREEN WASH / WIPE (1/3) Vehicles with automatic wiper function With the engine running, move stalk 1 – A park. – B automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed.
Page 65: Windscreen Washer
WIND SCREEN WASH / WIPE (2/3) Do not try to lift the wiper blades. They cannot remain detached from the windscreen. To replace the In freezing or snowy weather, ensure blades, refer to Section 5: “Wiper they are not stuck to the windscreen blades”.
Page 66 WIND SCREEN WASH / WIPE (3/3) In the event of obstacles present on the windscreen (dirt, snow, ice, etc.), clean the windscreen (inclu- ding the central area located behind Before performing any the interior rear-view mirror) and action in the engine com- the rear screen before starting the partment, the ignition must wipers (risk of motor overheating).
Page 67 REAR SCREEN WASH, WIPE Rear screen wash/wipe With ignition on, turn the end of the stalk 1 to bring the mark 2 in line with the symbol. When the stalk is re- leased, it returns to the rear windscreen In freezing or snowy weather, ensure wiper position.
Page 68: Fuel Tank
FUEL TANK (1/2) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must comply with the specifications given on the label on the cover A. Please refer to the in- formation on “Engine specifications” in Section 6.
Page 69 FUEL TANK (2/2) Filling with fuel Diesel versions It is essential to use diesel fuel that con- With the ignition off, insert the nozzle firms to the specifications given on the and insert it fully before turning it on to label inside fuel flap A.
Page 70 1.66...
Page 71 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in, Starting, Stopping the engine ..........Gear lever/Handbrake .
Page 72: Running In, Starting/Stopping The Engine
In this case, RENAULT card must not Service intervals: refer to the be located in the luggage compartment. Maintenance Document for the vehi-...
Page 73: Special Features
(radio, navigation, wipersetc.,). For other functions, - vehicles with remote control RENAULT CARD, insert the card into reader 1. - vehicles with a RENAULT hands-free card, with the card in the passenger...
Page 74 In certain cases, the RENAULT hands- free card may not work: With the card in reader 1, press button 2 : the engine will stop. Removing the - when the RENAULT card battery is card from the reader locks the steering flat, drained etc.., column.
Page 75: Gear Lever/Handbrake
GEAR LEVER/HANDBRAKE Handbrake Make sure that the hand- brake is properly released To release when driving (hand brake Pull the lever 3 up slightly, press button warning light off),otherwise 2 and then lower the lever to the floor. over heating, or even damage may occur.
Page 76: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 77: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 78: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Driving style indicator 2 Fuel consumption is accredited in ac- cordance with a standard regulatory (depending on variants) method. Identical for all manufactu- Informs you about the driving style rers, this enables vehicles to be com- adopted in real time.
Page 79: Journey Record
DRIVING ADVICE, ECO-DRIVING (2/5) An overall rating from 0 to 100 is dis- played to let you assess your eco driv- ing performance. The higher the rating, the lower the fuel consumption. Eco advice is given to help improve your performance. With your favourite journeys saved, you can evaluate your performance.
Page 80 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode ECO mode is a function which op- timises fuel consumption. It acts on certain power consuming systems in the vehicle (heating, air conditioning, power-assisted steering, etc.) and on certain driving actions (acceleration, gear changing, cruise control, deceler- ation, etc.).
Page 81 DRIVING ADVICE, ECO-DRIVING (4/5) – Avoid sudden acceleration. – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level.
Page 82 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 83: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life, which entered nents with parts other than those origi- be replaced.
Page 84: Environment
ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Our vehicles are equipped with a par- its entire service life: during production, centres to ensure that it is recycled.
Page 85: Driving Correction Devices / Aids
DRIVING CORRECTION DEVICES / AIDS (1/4) ABS (anti-lock braking Depending on the vehicle, this is com- posed of: system) – the (anti-lock braking In an emergency, apply firm and Under heavy braking, the ABS prevents system); continuous pressure to the brake the wheels from locking, allowing the –...
Page 86 DRIVING CORRECTION DEVICES / AIDS (2/4) Emergency brake assist with Operating faults Operating faults electronic brake distribution When the system detects an operating – If the warning light on the in- (depending on the vehicle) © fault, warning light. comes on. strument panel comes on while you Consult an approved dealer.
Page 87: Electronic Stability Program
DRIVING CORRECTION DEVICES / AIDS (3/4) Electronic stability program Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an opera- and traction control ESC in the case of pronounced under- ...
Page 88 DRIVING CORRECTION DEVICES / AIDS (4/4) Hill start assistance (depending on the vehicle) This function assists the driver when The hill start assistance starting on hills. It prevents the vehicle system cannot completely from rolling forwards or backwards by prevent the vehicle from automatically applying the brakes when rolling backwards in all sit- the driver lifts their foot off the brake...
Page 89: Speed Limiter
SPEED LIMITER(1/3) The speed limiter function helps you Controls Indicator light Ð stay within the driving speed limit that This warning light 6 on the 1 Main ON/OFF switch; you choose. instrument panel comes on to indicate 2 Limit speed activation , storage and This may be useful, for example, when that the limiter function is in operation.
Page 90 SPEED LIMITER (2/3) Limiting the speed At a stable speed (from approximately (18 mph) 30 km/h) press switch 1: the function is activated. Varying the limit speed You may change the limit speed at any time by pressing – 2 (+) to increase the speed, –...
Page 91 SPEED LIMITER (3/3) Exceeding the limit speed In the event of an emergency It is possible to exceed the limit speed at any moment. To do this: depress the accelerator pedal firmly and fully (beyond the kickdown point). The vehicle speed flashes on the in- strument panel (trip computer) to inform you that the limit speed is being ex- ceeded.
Page 92: Cruise Control
CRUISE CONTROL (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- stances replace the driver’s respon- The cruise control function helps you to Controls sibility to respect speed limits and to maintain your driving speed at a speed...
Page 93 CRUISE CONTROL (2/4) Driving Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelera- tor pedal. Important: you are never- theless advised to keep your feet close to the pedals in order to react if neces- By Pressing switch 1, this warning light Activating cruise control...
Page 94 CRUISE CONTROL (3/4) Exceeding the cruising speed In the event of an emergency The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel.
Page 95 CRUISE CONTROL (4/4) Returning to the cruising Switching off the function speed Press the main switch 1 to deactivate this function. In this case, speed is no If a speed is stored, it can be longer stored. It is confirmed once the recalled,once you are sure that the warning lights 6 and 7 goes off.
Page 96: Parking Distance Control
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic detectors, installed in the rear bumper (depending on the vehi- cle), measure the distance between the vehicle and an obstacle whilst revers- ing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi-...
Page 97 PARKING DISTANCE CONTROL (2/2) Operating faults Depending on the vehicle, when the s y s t e m d e t e c t s o p e r a t - ing fault,you can hear a contin- uous beep sound lasting approxi- mately 3 seconds and then sound goes off,...
Page 98: Reversing Camera
REVERSING CAMERA (1/2) This function is an add tional aid. It cannot, there- fore, under any circum- stances replace the vigi- lance or the responsibility of the driver. The driver should always pay attention to sudden incidents during driving: always ensure that there are no moving obstacles (such as a child, animal, pram, bicycle, etc.) or small, narrow objects such as...
Page 99 REVERSING CAMERA (2/2) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. Static guide line 3: The static guide line 3 has coloured markers A, B and C showing the dis- The screen shows a reverse image.
Page 100 2.30...
Page 101: Your Comfort
Section 3: Your comfort Air Vents ..............Automatic climate control .
Page 102 AIR VENTS, air outlets (1/2) 1 Left-hand side window demister 6 Right-hand side window demister outlet. outlet. 2 Left-hand side air vent. 7 Driver/Passenger footwell 3 Centre air vents. heater/cooler outlets. 4 Windscreen demisting vents. 8 Air conditioning Control panel 5 Right-hand side air vent.
Page 103: Air Vents
AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Direction control Air flow Slide cursors 10 to the required posi- To open air vent 12, press on the air tion. vent (point 13) until it is open as far as required.
Page 104: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/4) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 6 to increase or reduce the ventilation speed.
Page 105 AUTOMATIC CLIMATE CONTROL (2/4) Clear View function Press button 3 – the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 106 AUTOMATIC CLIMATE CONTROL (3/4) Adjusting the distribution The air flow is mainly distrib- Ø uted between the front side of air in the passenger window demisting air vents and the compartment windscreen demisting vents. Press one of the buttons 4. The in- The air flow is mainly directed ½...
Page 107 AUTOMATIC CLIMATE CONTROL (4/4) Manual use Press button 7 – the integrated indica- tor light comes on. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows. We therefore advise you to return to au- tomatic mode as soon as air recircula- tion is no longer needed, by pressing button 7.
Page 108: Maintenance
AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
Page 109 AIR CONDITIONING: information and operating instructions (2/2) Type of refrigerant fluid Ñ Type of oil in the air condi-  tioning circuit Inflammable product  Consult the driver’s hand-  book Maintenance  Quantity of refrigerant fluid present in the ve- x.xxx kg hicle.
Page 110: Electric Windows
Driver’s responsibility 3 for driver to prevent operation of Never leave your vehicle with the rear electric windows. A confirma- RENAULT card inside, and never tion message will display in the leave a child, adult who is not self- cluster.
Page 111 (still on the closure side) for side, press the locking button on the Pressing the switch again stops the one second then lower and raise the RENAULT card twice in quick suc- window moving. window fully to reinitialise the system. cession hands-free mode, all the Note: If the driver’s window detects re-...
Page 112: Interior Lighting
INTERIOR LIGHTING (1/3) Courtesy lights Courtesy lights Map reading lights Depending on the vehicle,Using Depending on the vehicle,press Depending on the vehicle,press, switch 1 will activate: switch 3 for: - 5 for front passenger lights ON/OFF; – permanent lighting in position A; –...
Page 113 INTERIOR LIGHTING (2/3) Glove box light 10 Light 10 comes on when the cover is opened. Unlocking and opening the doors or tailgate switches on the timed - Depending on the vehicle, unloc- courtesy lights and lights. king and opening the doors/tail gate will switch ON the lights.
Page 114: Ambient Light
INTERIOR LIGHTING (3/3) Boot light 11 Ambient light 12 It comes on when the boot is opened. Depending on the vehicle, it is equip- ped with ambient light 12. This will glows when position lamp is ON and re- mains ON in low/high beam condition. In AUTO mode, ambient light 12 will be ON only in low beam ON condition.
Page 115: Storage, Cabin Fittings, Sun Visor
STORAGE, CABIN FITTINGS , SUN VISOR (1/4) Front door storage pockets 1 Sun visor storage 2 Centre console storage compartment 3 They can hold a 1 litre bottle. This can be used for storing motorway tickets, cards, etc. Nothing should be placed Ensure that no hard, heavy on the floor area in front of or pointed objects are...
Page 116 STORAGE, CABIN FITTINGS , SUN VISOR (2/4) Dashboard storage Glovebox 6 Cooled Glovebox 7 compartment 5 To open the glove box, lift catch 6. Depending on the variant, opening/ closing along the arrow direction will To open it, press the lid 4. enable/disable the cooling inside glove box..
Page 117 STORAGE, CABIN FITTINGS , SUN VISOR (3/4) Front seat storage pockets 8 Rear door storage compartment 9 They can hold a 0.5-litre bottle. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passen- gers during sudden turning, braking or in the event of an accident.
Page 118 STORAGE, CABIN FITTINGS , SUN VISOR (4/4) Courtesy mirrors 11 12 Lift the cover 12 Depending on the vehicle, the light 13 comes on automatically. Grab handle 10 Front sun visor This offers support and can be held Lower the sun visor 11 over the wind- when the vehicle is being driven.
Page 119: Accessories Socket
ACCESSORIES SOCKET Accessories sockets 1, 2 Connect accessories with They are provided for connecting ac- a maximum power of cessories approved by our Technical 120 watts (12 V) only. Department. When several accessory sockets are used at the same time, the total power of the connected accessories must not exceed 180 watts.
Page 120: Rear Headrests
REAR HEAD RESTS Position for using headrest A To put the headrest back in place A Lift the headrest to maximum height, then lower it until it locks. Insert the rods in the holes, press button 1, lower the headrest and check that it is securely in place.
Page 121: Rear Bench Seat: Functions
REAR BENCH SEAT: FUNCTIONS (1/2) To reposition the seat back A – Lift the seat back; – make sure you lock the seat back in place. The seatback may be folded down to To fold the back A allow bulky objects to be transported. –...
Page 122 REAR BENCH SEAT: FUNCTIONS (2/2) When refitting the seat- back, make sure it is cor- rectly locked in place. If seat covers are fitted, make sure these do not prevent the seatback latch from locking in. Make sure that the seat belts are positioned correctly.
Page 123: Luggage Compartment
BOOT To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.
Page 124 REAR PARCEL TRAY The parcel shelf 2 is made up of two Lift the parcel shelf 2 to half height and rigid sections. unclip the mountings 3 located on each side of the parcel shelf. Gently lift the parcel shelf 2 and pull it Removal towards you, holding it at each end.
Page 125: Transporting Objects In The Luggage Compartment
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT If you have to place objects on the Always position the objects transported folded seatback, it is necessary that so that the largest surface is against: you lower the headrests before folding the seatback so that it can be folded as flat as possible against the seat.
Page 126: Multimedia Equipment
MULTIMEDIA EQUIPMENT The presence, operation and location of this equipment depends on the ve- hicle version. 1 Multimedia touchscreen; 2 Multimedia sockets; 3 Voice commands; 4 Steering column control; 5 Microphone. Refer to the equipment instructions for information on how to operate Using the telephone this equipment.
Page 127 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 128: Bonnet
BONNET (1/2) Do not press down on the bonnet: there is a risk that the bonnet may accidentally close. To open the bonnet, pull handle 1. Closing the bonnet Before closing the bonnet, make sure Unlocking the bonnet latch that nothing has been left in the engine compartment.
Page 129 BONNET (2/2) Before performing any action in the engine com- partment, the ignition must be switched off by press- ing the engine stop button, do not activate the remote engine start-up and ensure that its programming is not activated (please refer to the in- formation on “starting, stopping the engine”...
Page 130: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 131: Engine Oil Level: Topping Up/Filling
ENGINE OIL LEVEL - TOPPING UP,FILLING (1/2) Exceeding the maximum engine oil level Under no circumstances must the maximum fill level be exceeded: risk of damage to the engine and catalytic converter. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
Page 132: Oil Change
ENGINE OIL LEVEL - TOPPING UP,FILLING (2/2) Oil change Filling: take care when Before performing any Service interval: refer topping up the oil that action in the engine com- Maintenance Service Booklet for your no oil drips onto engine partment, the ignition must vehicle.
Page 133: Levels
LEVELS (1/3) Level Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI” warn- Only use fluids approved by our ing line shown on brake fluid reservoir1.
Page 134: Coolant
LEVELS (2/3) Coolant level checking frequency Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 135: Filters
LEVELS (3/3) Filters The filter elements (air filter, passenger compartment filter, etc.) should be re- placed during the maintenance opera- tions carried out on your vehicle. Consult an approved dealer at once Replacement intervals for filter el- if you notice an abnormal or re- ements: refer to the Maintenance peated drop in any of the fluid levels.
Page 136: Tyre Pressure
TYRE PRESSURE For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile should be used on a single axle. Label A B: dimension of the tyres fitted to the They must: either have a load ca- vehicle.
Page 137: Battery
BATTERY (1/2) The charge status of your battery can Handle the battery with care decrease especially if you use your ve- as it contains sulphuric acid, hicle: which must not come into – for short journeys; contact with eyes or skin. If it does, wash the affected area with –...
Page 138 BATTERY (2/2) Label A Observe the indications on the battery: – 2 naked flames and smoking are for- bidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; Please note when work- – 6 refer to the handbook; ing close to the engine that –...
Page 139: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 140 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning Scrapping off mud or dirt without equipment or by spray- pre-wetting. ing on products not ap- Allow dirt to accumulate on the exterior. proved by our Technical Department on below Allow rust to form following minor im-...
Page 141 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning the headlights finish Return the windscreen wiper stalk to As the headlights are made of plastic the Park position (refer to the informa- “glass”, use a soft cloth or cotton wool This type of paint requires certain pre- tion on the “Windscreen washer, wiper”...
Page 142: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 143: The Vehicle
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 144 4.18...
Page 145: Practical Advice
RENAULT card: battery ........
Page 146: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) To store the wheel in the cage: – clip protector 2 onto the punctured wheel; Never leave tools unse- – turn the puncture wheel over and cured in the vehicle: there slide it into cage 4; is a risk that they may be –...
Page 147 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use. Vehicle fitted with an emergency spare wheel that differs from the other wheels: –...
Page 148: Tools
TOOLS (1/2) Never leave tools unsecu- red in the vehicle: there is a risk that they may be thrown Accessing the tools After using the tools, make sure you about during braking. After close the flap A properly. The tools are located in the luggage use, make sure the tools are cor- compartment.
Page 149 TOOLS (2/2) Jack 2 Hubcap tool 3 Towing hitch 4 To use the jack, unscrew nut 6. When This tool is used to remove the wheel Please refer to the information on replacing the jack, fold it up completely trims. «Towing: breakdowns»...
Page 150: Changing A Wheel
CHANGING A WHEEL (1/2) Mark hole 1, which is the nearest to Switch on the hazard warn- the wheel in question. The jack must ing lights. be fitted in this location. Offer up jack 3 horizontally and position jack head 2 Park the vehicle away from under the sill.
Page 151 CHANGING A WHEEL (2/2) If the vehicle is not equipped with a jack or wheelbrace, you can obtain these from your approved dealer. Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Tighten the bolts, checking that the make sure the tools are correctly wheel is correctly positioned on its hub...
Page 152: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.
Page 153: Tyre Pressures
TYRES (2/3) Tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre or following a fast journey. pressures should be checked at least If tyre pressures cannot be checked once a month and additionally before...
Page 154: Changing Wheels Around
TYRES (3/3) Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhe- sion. Warning: These tyres sometimes have a specific direction of rotation and a maximum speed index which may be lower than the maximum speed of your vehicle.
Page 155 FRONT HEADLIGHTS: replacing the bulbs (1/2) Main beam headlight To change the bulb: – remove cover B; – disconnect the wiring 4 (black lead); – unclip the spring 3 and remove the bulb. Bulb type: H7. It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights.
Page 156: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: replacing the bulbs (2/2) Additional lights If you wish to fit fog lights to your ve- hicle, please see an authorised dealer. To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an ap- proved dealer.
Page 157 REAR AND SIDE LIGHTS: changing bulbs (1/2) Side lights Unlock the clips 2 and 3 and release the connectors 4 to remove the bulb Consult an approved dealer holders 5. Change the bulb. Brake lights and direction indicator lights 6 Direction indicator lights Bulb type: PY21.
Page 158: Indicator Lights
REAR AND SIDE LIGHTS: changing bulbs (2/2) High level brake light 8 Number plate lights 10 Indicator lights 12 Consult an approved dealer. – Unclip light 10 by pressing tab 11; The wing mirror needs to be removed; consult an authorised dealer. –...
Page 159: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/2) Courtesy light Glove box light Courtesy lights Unclip the lens (using a flat-blade Unclip light 2 using a flat-blade screw- Unclip the light 3 by pressing the tab on screwdriver or similar). driver or similar, by pressing on the tab its left side (using a flat-bladed screw- to move the light towards the inside of driver or similar).
Page 160 INTERIOR LIGHTING: changing bulbs (2/2) Ambient light 4 Luggage compartment light Access the bulb 6. Type of bulb: W5W. Please contact an authorised dealer. Unclip the light by pressing the tab 5 with a flat-blade screwdriver or similar. Disconnect the light. 5.16...
Page 161: Fuses
FUSES (1/4) Fuses in passenger compartment A Clip 1 Fuses in engine compartment B Some functions are protected by fuses If any electrical component does not Remove the fuse using tweezers 1, lo- located in the engine compartment work, check the condition of the fuses. cated at the back of flap A.
Page 162 FUSES (2/4) Allocation of fuses in the passenger compartment (presence of some fuses DEPENDS ON VEHICLE EQUIPMENT LEVEL) 5.18...
Page 163 FUSES (3/4) Number Allocation Number Allocation Number Allocation Accessories relay 2 Main beam headlight/ Engine Function Dipped beam headlight/ After ignition relay 1 Front Fog light/Reat Fog Air bag light Accessories relay 1 Reversing lights Electric window closer Rain/light sensor, opening control relay element warning sound/ Variable power assisted...
Page 164 FUSES (4/4) Number Allocation Number Allocation HFM / EMM Passenger electric window relayed supply Computer-Fuse protected battery Accessories relay 1 control Electric door locking After ignition relay 1 & 2 Driver side window motor control Accessories relay control 2 Accessories socket 2/ Alarm Accessories feed Instrument panel ECU...
Page 165: Renault Card: Battery
(insert the next time the vehicle is started, the ment panel, replace the RENAULT card the RENAULT card in the card reader) message will disappear. battery, press button 1, pulling on inte- and lock/unlock the vehicle (refer to the...
Page 166: Battery: Breakdown Recovery
BATTERY: BREAKDOWN RECOVERY (1/2) To avoid all risk of sparks: Connecting a battery charger Handle the battery with care – Ensure that any electrical consumers The battery charger must be com- as it contains sulphuric acid, (courtesy lights, etc.) are switched off patible with a battery with nominal which must not come into before disconnecting or reconnecting...
Page 167 BATTERY: BREAKDOWN RECOVERY (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross sec- tion) from an approved dealer or, if you a ready have jump leads, ensure that they are in perfect condition.
Page 168: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 169: Windscreen Wiper Blades
WINDSCREEN WIPER BLADES (1/2) Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
Page 170 WINDSCREEN WIPER BLADES (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 5 – With the ignition off, lift wiper arm 6; –...
Page 171: Automatic Gearbox
(lever in position D served. or R for vehicles with automatic trans- missions), insert the RENAULT card in the card reader then press the engine start button for two seconds. Reposition the lever to neutral (posi-...
Page 172: Towing
TOWING: breakdown (2/3) Only use the towing eye 4 and the wheelbrace located under the lug- gage compartment carpet in the tool kit (please refer to the information under “Tools” in Section 5). – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed Only use the front 3 and rear 6 towing...
Page 173 TOWING: breakdown (3/3) Off-road recovery If your vehicle is stuck in sand, snow or mud, attach a flexible towing device (towing belt or other device specially designed for this purpose) to the front or rear towing point (refer to the in- formation on “Front and rear towing points”...
Page 174: Operating Faults
Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the in- formation on “Locking, unlocking the open-...
Page 175 Starting conditions are not Please refer to the information on “Starting, stopping fulfilled. the engine” in Section 2. The RENAULT “hands-free” Insert the card in the card reader in order to start the card does not work. engine. Please refer to the information on “Starting, stopping the engine”...
Page 176 OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 177 OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Whistling Roof aerial poorly positioned. Position the aerial. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
Page 178 OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information in the “Fuses”...
Page 179 OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel Fault in the assistance system. needed to turn the wheels. Consult an ap- proved dealer.
Page 180 5.36...
Page 181: Technical Specifications
Section 6: Technical specifications Vehicle identification plate ............Engine identification plate .
Page 182: Vehicle Identification Plate
VEHICLE IDENTIFICATION PLATES The information shown on the ve- hicle identification plate should be quoted on all correspondence or orders. The presence and location of the in- formation depends on the vehicle. Vehicle identification plate A 1 Manufacturer name. 2 Identification number. 3 Paint reference (colour code).
Page 183: Engine Identification Plate
ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 184: Dimensions
DIMENSIONS (in metres) 1,558 0,850 2,673 0,806 1,813 4,329 1,619* 1,560 * unladen...
Page 185: Engine Specifications
ENGINE SPECIFICATIONS Versions 1.5 16V 1.5 dCi Engine type (see engine plate) Cubic capacity (cc) 1,498 1,461 Type of fuel Petrol Diesel Octane rating The use of unleaded petrol is essential, with the octane rating as stated The label located in the on the label inside the fuel filler flap.
Page 186: Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Minimum Weight - Unladen condition 1290 Kg (Depending on vehicle) Maximum Weight - Unladen condition 1375 Kg (Depending on vehicle) Maximum Weight - Laden condition 1800 Kg...
Page 187: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 188: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 189 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 190 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 191 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 192 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 193 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 194: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
Page 195 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 196 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 197 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 198 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 199: Alphabetical Index
ALPHABETICAL INDEX (1/4) changing gear ..............2.8 ABS ................1.44, 2.15 child restraint/seat ..........1.26→ 1.39 accessories................ 5.24 child safety..............1.26→ 1.39 accessories socket ............3.18 cleaning: additional methods of restraint ......... 1.25 inside the vehicle ..........4.16 – 4.17 side protection ............. 1.24 clock ...............
Page 200 ALPHABETICAL INDEX (2/4) emergency brake assist............. 2.16 emergency braking ............2.16 gear lever................2.5 engine glove box ................3.15 technical specifications ..........6.5 grab handle................ 3.17 engine coolant ..............4.8 engine oil ..............4.4 → 4.6 handbrake................2.5 engine oil grade ............4.5 → 4.7 hands-free telephone integrated control ......
Page 201 ............4.16 – 4.17 batteries ............... 5.21 mechanical .......4.4, 4.11 – 4.12,6.8 → 6.13 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.12 map reading lights ............. 3.12 replacement parts ..............6.7 methods of restraint in addition to the front seat belts..1.20 1.25 reverse gear multimedia equipment ............
Page 202 ALPHABETICAL INDEX (4/4) traction control ..............2.17 seat belts ...............1.16 → 1.19 transporting children ..........1.26 → 1.39 service sheets............6.8→ 6.13 transporting objects side protection devices ............1.24 in the luggage compartment ........3.24 signals and lights ..........1.53 → 1.57 on roof ................6.6 special features of diesel versions........

Renault Captur Driver's Handbook Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Related Manuals for Renault Captur

Summary of Contents for Renault Captur

Table of Contents