How To Use Advanced Functions; Direct; Swing; Sleep - Carrier RG56N Series Owner's Manual

HOW TO USE ADVANCED FUNCTIONS

Press Direct button

Direct

The horizontal louver will move an angle of 6 degree for each press.
Press the button until the louver reach your prefer location.
Press Swing button
In AUTO mode for heat pump system, the air conditioner can automatically choose the mode of Cool, Heat, Fan
by sensing the difference between the actual room temperature and setting temperature.

Swing

The horizontal louver will swing up and down
automatically when pressing Swing button.
Press again to make it stop.
Press Sleep button (RG56N) under Cool/Heat mode
The set temp. will increase
(cooling) or decrease
(heating) by 1 C per hour

Sleep

for the first 2hs. Thereafter
Sleep
it keeps this new temp. for
5hs before switching off.
This Sleep operation saves energy and improves night time comfort by synchronising with the
body's metabolism.
Press X-ECO button (RG56V) under Cool mode
The unit will automatically
regular the fan speed and
compressor speed. The
X-ECO
X-ECO
temp. can be selected from
or
24~30 C in ECO mode.
Sleep The function will be disable
after 8hs.
This X-ECO and Sleep operation saves energy and improves night time comfort by synchronising with the
body's metabolism.
Note: The X-ECO function is invalid for multi system.
07
Press Swing button for more than 2 sec
2s
Keep pressing this button more than 2 seconds, the vertical
louver swing function is activated. (Model dependent)
Press more than 2 seconds under Cool/Heat operate mode for Sleep
2s
The set temp. will increase
(cooling) or decrease
(heating) by 1 C per hour
X-ECO
for the first 2hs. Thereafter
it keeps this new temp. for
5hs before switching off.
Press this button more than 2 seconds
2s
My Mode The unit will memorize
My
the current setting
Mode
mode, Temp., fan).
My mode function enable you to memorize or restore your favorite settings (mode, temperature and fan
speed). The default memorized setting is AUTO mode, 26 C and AUTO fan.
Press this button under COOL or HEAT operating Mode
The controller will display
Follow Me
Follow the actual temp. at its
location and send this
Me
signal to indoor unit
Fresh
or
every 3 minutes
Fresh
Press this button to activate Follow me. This function
can adjust room temperature base on the controller's
sensor and make you comfort.
Note:Please put the controller in the location where
can ensure the indoor unit can receive the signal.
Press LED button
LED
LED
or
Self Clean
Self
Clean
Press this button to turn on and turn off the display
on the indoor unit.
Press this button
The unit will operate at the
Turbo
Turbo
biggest capacity outut to
reach the setting Temp. quickly.
or
Silence
Silence
Press this button to activate Turbo. It enables
the unit to reach the set temperature in
the shortest time. Press it again to disable it.
Press this button
My Mode
The unit will restore to
the setting you made
last time.
Press this button more than 2 seconds
2s
The ionizer or Plasma
Follow Me
dust collector (model
dependent) is energized.
Fresh
Keep pressing this button more than 2 seconds, the
fresh function is activated and will help to remove
pollen and impurities from the air. (Model dependent)
Press this button under COOL or DRY Mode more than 2 seconds
2s
The unit will enter low
LED
fan mode to dry up the
coil. The cleaning cycle
Self Clean takes 15~30 mins, after
which the unit will turn
off automatically.
Keep pressing this button more than 2 seconds, the unit will
clean itself to avoid bacteria grow around heat
Cl dependent)
Press this button more than 2 seconds
2s
The unit will bring faint
Turbo
breeze to reduce the
noise to the lowest level .
Silence
Keep pressing this button more than 2 seconds, the Silence
function is activated. (Model dependent)
Note: Due to low speed of operation, it may result in
insufficient cooling and heating capacity.
08