Advertisement
Remote control
D Command table (Continued)
Cmd.
Sub cmd.
Data
20
07
00*
00/01
01
See p. 18
02
See p. 18
08
00*
00/01
01
See p. 18
02
See p. 18
09
00*
00/01
01
See p. 19
02
See p. 19
0A
00*
00/01
01
See p. 19
02
See p. 19
0B
00*
00/01
01
See p. 19
02
See p. 19
0C
00*
00/01
01
See p. 20
02
See p. 20
0D
00*
00/01
01
See p. 20
02
See p. 20
22
01
00*
00/01
01
See p. 20
25*
See p. 20
26*
See p. 21
27*
00
See p. 21
10
00/01
11*
00/01
2
12
00
13
00
14
See p. 22
15
See p. 22
17
See p. 22
19
See p. 22
1A
See p. 22
1C
00 ~ 02
1D
See p. 22
1E
See p. 22
*(Asterisk) Send/read data
Description
Send/read the P25 RX status output
setting
(00=Transceive OFF, 01=Transceive ON)
Output the P25 RX status for transceive
Read the P25 RX status
Send/read the dPMR RX ID output setting
(00=Transceive OFF, 01=Transceive ON)
Output the dPMR RX ID for transceive
Read the dPMR RX ID
Send/read the dPMR RX status output
setting
(00=Transceive OFF, 01=Transceive ON)
Output the dPMR RX status for transceive
Read the dPMR RX status
Send/read the NXDN RX ID output setting
(00=Transceive OFF, 01=Transceive ON)
Output the NXDN RX ID for transceive
Read the NXDN RX ID
Send/read the NXDN RX status output
setting
(00=Transceive OFF, 01=Transceive ON)
Output the NXDN RX status for transceive
Read the NXDN RX status
Send/read the DCR RX ID output setting
(00=Transceive OFF, 01=Transceive ON)
Output the DCR RX ID for transceive
Read the DCR RX ID
Send/read the DCR RX status output setting
(00=Transceive OFF, 01=Transceive ON)
Output the DCR RX status for transceive
Read the DCR RX status
Send/read the D-STAR RX data output
setting
(00=Transceive OFF, 01=Transceive ON)
Output the D-STAR RX data for transceive
Send/read the selected or not selected
VFO frequency
Send/read the selected or not selected
VFO's operating mode and filter
Read the Scope waveform data
Send/read the Scope ON/OFF status
(00=OFF, 01=ON)
Send/read the Scope wave data output
setting
(00=OFF, 01=ON)
Send/read the Scope MAIN/SUB setting
(00=Fixed to MAIN)
Send/read the Scope Single/Dual setting
(00=Fixed to Single)
Send/read the Scope Center mode or
Fixed mode setting
Send/read the span setting in the Center
mode Scope
Send/read the Scope hold function status
Send/read the Scope Reference level
Send/read the Sweep speed
Send/read scope center frequency
setting in the Center mode
(00=Filter Center,
01=Carrier Point Center,
02=Carrier Point Center (Abs. Freq.))
Send/read the Scope VBW setting
Send/read the Scope Fixed edge
frequencies
1
*
When sending the power ON command (18 01), you need
to repeatedly send "FE" before the standard format. The
following is the approximate number of needed repetition.
• 115200 bps: 119 "FE"s
• 57600 bps: 59 "FE"s
• 38400 bps: 40 "FE"s
• 19200 bps: 20 "FE"s
• 9600 bps: 9 "FE"s
• 4800 bps: 5 "FE"s
Example: When using 4800 bps
Preamble
F
E
F
E
F
E
×5
2
*
When you use the [USB (Front)] port, you need to select
"115200" in the "CI-V Baud Rate" item.
When you use the [USB (Rear)] port, you need to select
"Unlink from [REMOTE]" in the "CI-V USB port" item, and
need to select "115200" in the "CI-V Baud Rate" item.
You can use the [LAN] port regardless of those settings.
You cannot use the [REMOTE] terminal regardless of
those settings.
8
Controller's
Command
R8600's
Sub
address
address
command
9
6
E
0
1
8
0
1
Post
amble
F
D
Advertisement
