Related Manuals for Extreme Networks AP-7622
Summary of Contents for Extreme Networks AP-7622
-
Page 1: Installation Guide
AP-7622 Access Point Installation Guide Published October 2017 9035128-03 9035128-03 Published October 2017 9035128-03... -
Page 2: Legal Notices
Copyright © 2017 Extreme Networks, Inc. All Rights Reserved. Legal Notices Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. -
Page 3: Table Of Contents
Wall Mount Procedure ................................8 Ceiling Mount Instructions ..............................10 AP-7622 Beam Clip ..................................11 LED Indicators ................................... 12 Basic Configuration....................15 AP-7622 Access Point Specifications ..............19 Electrical Characteristics ..............................19 Physical Characteristics ..............................19 Radio Characteristics ..............................19 Regulatory Information ..................21 Regulatory Information .............................. - Page 4 Mexico ......................................29 South Korea ....................................30 Turkey ......................................30 Thailand ......................................30 Taiwan ......................................31 European Waste Electrical and Electronic Equipment (WEEE) Notice ............ 31 Turkish WEEE Statement of Compliance ......................32 AP-7622 RoHS Compliance ............................32 AP-7622 Access Point Installation Guide...
-
Page 5: Introduction
• Verify cable lengths are within the maximum allowable distances for optimal signal transmission. AP-7622 Package Contents An AP-7622 Access Point is available in internal antenna (AP-7622) configurations. An AP- 7622 ships with the following: • AP-7622 Access Point • AP-7622 Quick Install Guide... -
Page 6: Ap-7622 Antennas
The GE1/POE accepts 802.3at or 802.3af compliant power from an external source. NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended for Gigabit operation. AP-7622 Antennas An AP-7622 internal antenna Access Point supports the following: 2.4 GHz Gain (dBi) 5 GHz Gain (dBi) 3.64dBi 5.77dBi... -
Page 7: Hardware Installation
Hardware Installation Installation Instructions An AP-7622 Access Point mounts either on a wall or on a suspended ceiling T-Bar. To prepare for the installation: To prepare for the installation: 1 Match the part number on the purchase order with the part numbers in the packing list and on the case of the Access Point. -
Page 8: Access Point Placement
Access Point. Power Injector System An AP-7622 Access Point can receive power via an Ethernet cable connected to the GE1/ POE (LAN) port. When users purchase a WLAN solution, they often need to place Access Points in obscure locations. - Page 9 Access Point) could either limit functionality or severely damage the Access Point and void the product warranty. A separate Power Injector is required for each AP-7622 Access Point comprising the network. The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the power injector’s wall mounting key holes.
-
Page 10: Mounting Instructions
Installation Guide shipped with the Power Injector for a description of its LEDs. Mounting Instructions An AP-7622 can be mounted to a flat wall surface or on a T-Bar of a suspended ceiling. NOTE Before wall mounting the AP-7622, obtain the unit’s default IP address from the backside of the unit. - Page 11 When pre-drilling a hole the recommended hole size is 4mm (0.16in.). 2 Drill pilot holes at the locations marked on the wall.. 3 Cable the Access Point using the Power Injector solution, approved AP-7622 power supply or a POE enabled switch.
-
Page 12: Ceiling Mount Instructions
A ceiling mount requires holding the AP-7622 up against a T-Bar of a suspended ceiling grid and twisting the unit on to the T-Bar. If deploying the AP-7622 on a sculpted ceiling T- Bar, the Access Point mounting kit (Part No. KT-135628-01) can be used as well. A beam clip is also available to attach the Access Point to a ceiling beam. -
Page 13: Ap-7622 Beam Clip
AP-7622 Beam Clip When needed, an AP-7622 can also be ceiling mounted using a beam clip. If utilizing a beam clip, attach the beam clip to the AP-7622’s integrated mounting bracket. Then connect the Access Point to the ceiling beam. -
Page 14: Led Indicators
Hardware Installation LED Indicators The AP-7622’s three LED activity indicators are located on the front of the housing and are visible through the enclosure. The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11ac (amber) radio, 2.4 GHz 802.11n (green) radio and Bluetooth activity (blue) radio. - Page 15 On 1 second, Off 5 Not Connected seconds seconds Synced with Amber Synced with Green Locate AP Mode Irregular Blink Rate, Irregular Blink Rate, Irregular Blink Rate, Green/Amber/Blue Green/Amber/Blue Green/Amber/Blue Bluetooth Radio Solid Blue Enabled Bluetooth Radio Disabled AP-7622 Access Point Installation Guide...
- Page 16 Hardware Installation AP-7622 Access Point Installation Guide...
-
Page 17: Basic Configuration
1 Power the AP-7622 using an appropriate power adapter, PoE injector, or PoE switch. 2 Connect to the AP-7622. The default IP address is located on the backside of the AP- 7622. 3 Enter the default username admin in the Username field. - Page 18 Virtual Controller list this Access Point's AP Name as its own. Only one Virtual Controller can be designated. • Country Name - Set the country specific to this AP-7622's deployment location. Selecting the correct country is central to legal operation. Each country has its own...
- Page 19 • Date & Time -Set the date, hour and minute for the AP-7622's current system time. Specify whether the current time is in the AM or PM.
- Page 20 Basic Configuration AP-7622 Access Point Installation Guide...
-
Page 21: Ap-7622 Access Point Specifications
Power over Ethernet 48VDC, .25A, PoE Physical Characteristics An AP-7622 Access Point has the following physical characteristics: Dimensions 7.1 in. L x 6.5 in. W x 1.6 in. H 180 mm L x 165 mm W x 41 mm H Weight 0.85 lbs/0.385 kg... - Page 22 AP-7622 Access Point Specifications AP-7622 Access Point Installation Guide...
-
Page 23: Regulatory Information
Regulatory Information This guide applies to the following Model Number AP-7622. Extreme Networks devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following Website: www.extremenetworks.com/support... -
Page 24: Declaration Of Conformity In Languages Of The European Community
Declaration of Conformity in Languages of the European Community Hereby, Extreme Networks, Inc. declares that the radio equipment type Wireless LAN Access Point is in compliance with Directive 1999/5/EC. The full text of the EU declaration of conformity is available at the following Internet address: http://www.extremenetworks.com/... -
Page 25: Health And Safety Recommendations
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. • Should not carry the device in a breast pocket. • Should use the ear furthest from the pacemaker to minimise the potential for interference. AP-7622 Access Point Installation Guide... -
Page 26: Other Medical Devices
Alternately this device may be powered from a 802.3af compliant power source which has been certified by the appropriate agencies, or by an approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings: Output 48Vdc, min 0.25A, with a AP-7622 Access Point Installation Guide... -
Page 27: Radio Frequency Interference Requirements-Fcc
When using this device, it is recommended to have a separation distance of 20 cm. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radio Frequency Interference Requirements - Canada CAN ICES-3 (B)/NMB-3(B) Radio Transmitters AP-7622 Access Point Installation Guide... -
Page 28: Ce Marking And European Economic Area (Eea)
Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec une autre antenne ou émetteur. CE Marking and European Economic Area (EEA) The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions: AP-7622 Access Point Installation Guide... -
Page 29: Statement Of Compliance
• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 - 2.4835 GHz. Statement of Compliance Extreme Networks hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). -
Page 30: Australia
Además, de acuerdo con Resolución 755, para la banda 5150-5250MHz la operación del equipo estará restringida al interior de inmuebles y la densidad de potencia radiada máxima no supera 7,5mW/MHz en cualquier banda de 1MHz y 0.1875mW/25kHz en cualquier banda de 25kHz. AP-7622 Access Point Installation Guide... -
Page 31: China
This device conforms to technical specification in ETSI TS 123.038 V8.0.0 (or the code of any subsequent release) and ETSI TS 123.040 V8.1.0 (or the code of any subsequent release) which contain all Turkish characters. AP-7622 Access Point Installation Guide... -
Page 32: Thailand
European Waste Electrical and Electronic Equipment (WEEE) Notice In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE): The symbol above indicates that separate collection of electrical and electronic equipment is required. AP-7622 Access Point Installation Guide... -
Page 33: European Waste Electrical And Electronic Equipment (Weee) Notice
It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Customer Support at +353 61 705500 (Ireland). Turkish WEEE Statement of Compliance EEE Yönetmeliğine Uygundur AP-7622 RoHS Compliance AP-7622 Access Point Installation Guide...