Yamaha YSP-4300 Service Manual page 86

YSP-CU4300/YSP-CU3300/NS-WSW160
System Switching Pins
Pin
Function Name
No.
76 DSDA0
80 DSDA1
84 DSDA2
88 DSDA3
92 DSDA4
97 DSDA5
73 DSDA6(VGA)
77 DSCL0
81 DSCL1
85 DSCL2
89 DSCL3
93 DSCL4
98 DSCL5
74 DSCL6(VGA)
106 TXDSDA0
109 TXDSDA1
107 TXDSCL0
110 TXDSCL1
79 R0PWR5V
83 R1PWR5V
87 R2PWR5V
91 R3PWR5V
95 R4PWR5V
100 R5PWR5V
78 CBUS_HPD0
82 CBUS_HPD1
86 CBUS_HPD2
90 CBUS_HPD3
94 CBUS_HPD4
99 CBUS_HPD5
105 TX_HPD0
108 TX_HPD1
103 MHL_CD0/GPIO0
104 MHL_CD1/GPIO1
86
Type I/O
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
LVTTL Schmitt Open
Input
drain 5 V tolerant
LVTTL Schmitt Open
Input
drain 5 V tolerant
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
LVTTL Schmitt Open
Input/Output
drain 5 V tolerant
Power Input
LVTTL 1.5 mA 5 V
Input/Output
tolerant Analog
LVTTL 5 V tolerant Input
LVTTL 5 V tolerant Input
LVTTL Input/Output
LVTTL Input/Output
Detail of Function
DDC I2C data for respective HDMI receiver port.
These signals are true open drain, and do not pull to ground when power is not
applied to the device. These pins require an external pull-up resistor.
DDC I2C data for VGA port.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC I2C clock for respective HDMI receiver port.
These signals are true open drain, and do not pull to ground when power is not
applied to the device. These pins require an external pull-up resistor.
DDC I2C clock for VGA port.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C data for HDMI transmitter Port 0.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C data for HDMI transmitter Port 1.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C clock for HDMI transmitter Port 0.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
DDC master I2C clock for HDMI transmitter Port 1.
This signal is true open drain, and does not pull to ground when power is not
applied to the device. This pin requires an external pull-up resistor.
5 V port detection input for respective HDMI receiver port.
Connect to 5 V signal from HDMI input connector. These pins require a 10 ohms
series resistor, a 5.1 k-ohms pull down resistor, and at least a 1 μF capacitor to
ground.
Hot plug detect output for the respective HDMI receiver port.
In MHL mode, these pins serve as the respective CTRL bus.
Hot plug detect input for HDMI transmitter Port 0.
Hot plug detect input for HDMI transmitter Port 1.
MHL cable detect 0/programmable GPIO 0.
MHL cable detect 1/programmable GPIO 1.