Related Manuals for Planet Networking & Communication VIP-101T
Summary of Contents for Planet Networking & Communication VIP-101T
- Page 1 IP Phone VIP-101T CLI User’s Manual This document is a command-by-command description for the PLANET VIP-101T CLI administration mode.
-
Page 2: Fcc Compliance Statement
PLANET Technology. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. - Page 3 Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies.
-
Page 4: Table Of Contents
PLANET VIP-101T CLI configuration Command Line Interface Configurations ...1 1. [help] ... 1 2. [quit] ... 2 3. [reboot] ... 2 4. [flash]... 3 5. [commit]... 4 6. [ifaddr] ... 4 -ip, -mask, -gate ... 5 b) -dhcp ... 6 c) –sntp ... - Page 5 PLANET VIP-101T CLI configuration d) –keypad ... 18 e) –idto ... 19 f) –eod ... 19 g) -h450... 19 13. [h323] ... 20 a) –print ... 21 b) –mode ... 21 c) –gk ... 22 d) –dfgw ... 22 e) –algk ... 23 f) –gkname ...
- Page 6 PLANET VIP-101T CLI configuration b) –fstart ... 35 c) –tunnel ... 35 d) -h245fs ... 35 17. [bureau] ... 36 a) -print... 36 b) -hold ... 37 18.[rom] ... 37 a) -print... 37 b) -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and –htpcm ... 37 c) -boot2m ...
-
Page 7: Command Line Interface Configurations
4. Please use ”commit” command for parameter confirmation, and all modifications should be activated via command “reboot” After log into the VIP-101T, the terminal will prompt with “usr/config$”, this shows you are log into the CLI of the VIP-101T successfully. Operation commands in command line interface (CLI) are introduced in respective session, please press either “?”... -
Page 8: Quit]
Password setting information and configuration usage: help [command] 2. [quit] Type either quit, exit, or close in CLI will logout VIP-101T Telnet administration session. Syntax Description This command has no arguments or keywords. Default This command has no default value. -
Page 9: Flash]
PLANET VIP-101T CLI configuration no committed data, reboot command will restart machine only. Syntax Description This command has no arguments or keywords. Default This command has no default value. Example usr/config$ reboot Data modified, commit to flash rom?(y/n)y This may take a few seconds, please wait... -
Page 10: Commit]
IP address: 192.168.0.1, Web/Telnet logon username: root; password: <null>, press <Enter> to log in machine.. 6. [ifaddr] Command ifaddr is used to configure and display TCP/IP related information in VIP-101T. There are sub parameters in this menu, please insert “ifaddr” to display related parameters for configuration. -
Page 11: A) -Ip, -Mask, -Gate
-dns 1 168.95.1.1 ifaddr -timezone 8 a) -ip, -mask, -gate These parameters are used to setup IP Address, subnet mask and default gateway respectively. Syntax Description Specify IP address of VIP-101T. -mask Set Internet subnet mask. - 5 -... -
Page 12: B) -Dhcp
TCP/IP status on the LCD panel. c) –sntp SNTP feature in VIP-101T is able to retrieve time information from timeserver on the net. To enable the SNTP feature in machine, please assign the trigger parameter “1”, and SNTP IP address in SNTP parameter. -
Page 13: E) -Timezone
2. If you’d like to use domain name as calling destination, please refer to H.323 and Phone Book sessions for more configuration tips. e) –timezone If the SNTP server is configured, you can setup time zone information in VIP-101T to meet local time display. Syntax Description –timezone 8... -
Page 14: Time]
PLANET VIP-101T CLI configuration 7. [time] Command time is used to display current time information. This function is valid only when SNTP server is configured in VIP-101T’s SNTP function. usr/config$ time Current time is FRI JAN 23 18:08:00 2003 If time information cannot display properly, please check command: ifaddr -sntp for Hint configuration tips. -
Page 15: Pbook]
(ms) min/avg/max = 0/1/5 9. [pbook] Phonebook in VIP-101T is the phone number database for connection toward other H.323 terminal/gateway. This command is provided for Peer-to-Peer Mode use only. While machine is running in GK mode, dial-string depends on the registration information provided by ITSP or assigned from GK administrator. - Page 16 PLANET VIP-101T CLI configuration Example usr/config$ pbook Phonebook information and configuration Usage: pbook [-print [start_record] [end_record]] pbook [-add [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-search [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-insert [index] [ip ipaddress] [name Alias] [e164 phonenumber]]...
-
Page 17: A) -Print
PLANET VIP-101T CLI configuration a) –print Parameter print can be used to display phone book database information. You can display all data in phone book by adding –print parameter. Furthermore, you like to display a section of data, indication parameter 'start_record' and 'end_record' can be used (pbook –print “start index #”... -
Page 18: C) -Search
This command has no arguments or keywords Default This command has no default value. d) -delete Parameter delete can be used to delete a telephone entry in VIP-101T phone book database. Syntax Description –delete index number Default This command has no default value. -
Page 19: F) -Modify
When dialing, please press ” # ” after dialing E.164 number to send out telephone Hint number to destination. 10.[pppoe] VIP-101T equipped with PPPoE client, this makes VIP-101T is able to establish Internet connection without assistance. Example usr/config$ pppoe PPPoE device information and configuration... -
Page 20: B) -Dev
Enable(=1) or Disable(=0) PPPoE function in VIP-101T Default 0 PPPoE function in VIP-101T is turned off. c) –open While VIP-101T is not in PPPoE connection state, you may use parameter –open to initiate a PPPoE connection. Syntax Description -open Initiate a PPPoE connection. -
Page 21: E) -Id
PPPoE conhnection. After reboot, if VIP-101T still can’t get contact with server, VIP-101T will keep trying to connect one more time. On the other hand, if this function is disabled, VIP-101T won’t reboot and keep trying to connect. -
Page 22: 11. [Ddns] Command
VIP-101T is behind IP sharing, it will send it’s private IP address to DDNS server. 8. -checkipsrv: to set IP address of IP address check server. 9. -delay: to set the update interval time. VIP-101T will re-update it’s IP address in this time. (ddns –delay 1-59m/1-24h , m means minute, h means hour) –force: to force to execute DDNS update. -
Page 23: 12.[Sysconf] Command
PLANET VIP-101T CLI configuration 12.[sysconf] command This command displays the system information and configuration. System information and configuration Usage: sysconf [-plan digits] [-callalive flag] [-h450 flag] [-keypad type] [-idto time] [-eod type] sysconf -print -print Display system overall information and configuration. -
Page 24: C) -Callalive
“#” key to send out numbers to desired destinations. c) –callalive VIP-101T is able to check if there are network activities during calling process. Parameter –callalive can enable or disable auto-disconnect operation after 10 seconds not receiving packets from remote calling party... -
Page 25: E) -Idto
Interval between dial string Digits. Default 5 seconds f) –eod Terminal digit selection, once this specified digit is pressed on the keypad, VIP-101T will send out the dialed digits. Syntax Description –eod 0/1/2/3 (0 for no end of dial key , 1 for “OK” button , 2 for “#” button , 3 for “＊”... -
Page 26: H323]
PLANET VIP-101T CLI configuration 13. [h323] h323 command is used to display or configure H.323 parameters in VIP-101T, these parameters are designed to meet most calling environment. It is strongly recommended not to modify these parameters on your own. If you met difficulty to establish communication toward destination call party, please consult ITSP engineering staff, experienced personnel or local distributor support staff for proper configuration. -
Page 27: A) -Print
Parameter –print is used to display H.323 stack information and configuration. Syntax Description This command has no arguments or keywords. Default This command has no default value. b) –mode VIP-101T is capable of running in Peer-to-Peer or GateKeeper mode. Machine default - 21 -... -
Page 28: C) -Gk
Domain Name Server must be configured in -ifaddr configuration menu, so that the URL can be functional here. Note 2. If GK IP address is set to 255.255.255.255; VIP-101T will be set to run Gatekeeper Auto-discovery mode. It is required to configure parameters –gkname and –gkdis to complete the GK Auto-discovery configuration. -
Page 29: E) -Algk
–algk This parameter is used to configure secondary Gatekeeper IP address or URL address. If VIP-101T tries to register to primary Gatekeeper for 10 times but failed, it will try to register to secondary (alternative) Gatekeeper configured in this option. -
Page 30: H) -E164-X
E.164 number filed also can be used in Peer-to-Peer mode as the destination number. Note i) –alias Parameter –alias is used to identify H.323 ID for VIP-101T to register with Gatekeeper. Default alias is related to MAC address of VIP-101T, so each VIP-101T has different alias, which can register with GK without conflict. -
Page 31: J) -Tokenpwd
PLANET VIP-101T CLI configuration j) –tokenpwd To co work in a H.235 security environment, VIP-101T is implemented the capability of sending RRQ/ARQ authentication token password to Gatekeeper for authentication purpose. Syntax Description -tokenpwd RRQ/ARQ authentication token password while registering toward Gatekeeper. -
Page 32: L) -Rtp
PLANET VIP-101T CLI configuration l) –rtp This parameter is used to assign RTP port number for voice packet transmission, definable port range: 1024-65535. Syntax Description -rtp RTP port number (1024~65532). Default 16384 m) –ttl This parameter is used to set RAS TTL (time-to-live) time while machine performs registration toward Gatekeeper. -
Page 33: P) -Range
This parameter is used to assign dynamically allocated port range, definable port range: 1024-65535. Syntax Description -range Dynamically allocated port range (1024~65535) in VIP-101T. Default 1024-65535 q) –respto This parameter is used to setup Max. waiting time for first response from detination call party during call setup process. -
Page 34: Voice]
PLANET VIP-101T CLI configuration 1. Parameters in this H.323 configuration menu are not suggested to change without assistance of ITSP or experienced personnel, improper configuration will case communications fail or malfunction in machine. 2. In Peer-to-Peer mode, h323 –print will only display information on e164, alias, Note mode, RTP port, and allocated port range fields. -
Page 35: A) -Print
-volume voice 20 input 32 dtmf 27 voice -echo 1 1 usr/config$ a) –print Parameter –print is used to display voice codec information and configuration. Voice codec supports in VIP-101T are: G.723.1, G.729a, G.729, G.711u, G.711A. Syntax Description - 29 -... -
Page 36: B) -Send
PLANET VIP-101T CLI configuration -print Display voice codec information and configuration. Default This command has no default value. Example usr/config$ voice -print Voice codec setting relate information Sending packet size : G.723.1 G.729A G.729 G.711U G.711A Priority order codec :... -
Page 37: C) -Priority
30, input gain: 30, DTMF volume: 27 e) –nscng Parameter –nscng is used to enable or disable sound compression and comfort noise generation in VIP-101T. This parameter is only valid for codec G.723.1. (0 for off,1 for on) Syntax Description -nscng... -
Page 38: G) -Mindelay
Setting of echo canceller. (On=1, Off=0) Default 1 (echo canceller is turned on) g) –mindelay Parameter –mindelay is used to setup minimum delay of jitter buffer in VIP-101T, definable range: 0~150 ms Syntax Description -mindelay Setting minimum delay of jitter buffer... -
Page 39: Tone]
Busy tone, reorder tone, ring tone and dial tone are adjustable in VIP-101T. In most circumstances, there is no need to change tone setting. Currently, only ring tone and dial tone is functional in VIP-101T, busy tone and reorder tone are reserved for future use. usr/config$ tone... -
Page 40: Support]
Parameters in support configuration menu are used to adjust H.323 call setup related parameters. By default settings, VIP-101T is able to work well in most operation environment. If you met difficulties during call setup, please contact ITSP related personnel or your local... -
Page 41: A) -Print
H.323 fast start mode in VIP-101T, please make sure the destination call party supports fast start mode as well. Syntax Description -fstart Enabled or disabled Fast start mode in VIP-101T, o to disable, 1 to enable this feature.. Default H.323 fast start mode is disabled. -
Page 42: Bureau]
18. [bureau] This parameter is used while other call party supports H.450 Hold feature. If this feature is enabled, other call party will hear hole tone when “HOLD” button on VIP-101T keypad is pressed. usr/config$ bureau Bureau line setting information and configuration... -
Page 43: B) -Hold
This command has no default value. b) -hold If other terminals support H.450 hold function, and execute hold function when connecting with VIP-101T, user will hear hold tone from VIP-101T. (0 for off,1 for on) Syntax Description -hold Enable or disable H.450 service hold tone generation, 0 for disable and 1 for enable. -
Page 44: C) -Boot2M
PLANET VIP-101T CLI configuration Back Tone PCM file and Hold Tone. In most circumstances, upgrade the main application image can retrieve the latest features or maintenance, no other file required. If there are additional demands for other kinds of image file, we’ll include in the firmware release for customer’s most convenience. -
Page 45: F) -Server
–ftp Specify user name and password for FTP firmware upgrade method For example: User prepares to upgrade the latest app rom file –VIP-101T.030213r1, the TFTP server is 192.168.0.2. rom –app –s 192.168.0.2 –f VIP-101T.030213r1 (If the destination server is specified via parameter –server, you may insert command: rom –app –f VIP-101T.030213r1 to complete... -
Page 46: Passwd]
Example: passwd -set root vip100t a) –set Parameter -set is used to configure password for “root” or “administrator” users. Difference between root and administrator users in VIP-101T is root user has the privilege of performing firmware upgrade. Syntax Description -set login name password, login name should be root or administrator only. -
Page 47: B) -Clean
Parameter -clean can be used to erase the existing password stored in machine. To perfor this command, you need to logon as root user to have sufficient privilege to execute this command. After password erased, you may logon VIP-101T via username/password: root/ null<without password> or administrator/ null<without password>.