Advertisement
1.2.4
Overview of
Operating Parameters
I!J)
Function
Parameter
Axis·
v
Entry··
Radius/Diameter Xl
P 1.1
X
1
RadiuS/Olameter X2
P 1.2
y
2
Radius/Diameter X3
P 1.3
Z
3
RadiuS/Diameter X4
P 1.4
W
•
Angle Format
P 2.0
5
Scahng Factor Xl
P 3.1
X
6
Scaling Factor X2
P3.2
y
7
Scaling Factor X3
P3.3
Z
8
Scaling Factor X4
P3A
W
9
Scaling Factor ON
P4.0
10
Ball Diameter
P5.0
11
Tool Diameter
P60
12
Baud Rate RS 232-C
P70
13
Line Feed RS-232-C
PB.O
"
Mode of Operation
P9.0
0
Radius/Diameter Xl
P 21.1
X
radius,
Radius/Diameter X2
P 21.2
y
diameter
RadiuS/Oiameter X3
P21.3
Z
Radius/Diameter X4
P 21.4
W
Angle Format
P22.0
degrees decimal,
degreeS/min/sec
Scaling Factor Xl
P 23.1
X
1.000000
Scaling Factor X2
P23.2
y
(0.100000 to
Scaling Factor X3
P23.3
Z
9.9999991
Scaling Factor X4
P 23.4
W
Scaling Factor ON
P24.0
OFF, ON
BaU
Diameter
P25.0
10.000 (0 to
199.999 mm)
Tool Diameter
P 26.0
0.000
±
(0 to
1999.999 mm)
Baud Rate RS-232-C
P 27.0
9.600 (1l0. 150.
300.600.1200.
2400.4800.
9600. 19200.
38400 baud)
Une Feed RS-232-C
P2B.0
1 (0 to 99)
no
Technical Description
Operating Parameters (cant'd.1
I!J)
Function
Parameter Axis·
v
Entry··
Counting Direction Xl
P40.1
X
normal. inverse
Counting Direction X2
P40.2
y
Counting Direction X3
P40.3
Z
Counting Direction X4
P40.4
W
Signal Period Xl
P41.1
X
4 IJm. 10 IJm,
Signal Period X2
P41.2
Y
20 IJrn, 40 IJm.
Signal Period X3
P41.3
Z
100 IJm. 200 IJm
Signal Period X4
P41A
W
Line Count Xl
P 42.1
X
1800, 3600. 9000.
Line Count X2
P42.2
Y
18000.36000.
72000
Line Count X3
P42.3
Z
Line Count X4
P42.4
W
Linear Subdivision Xl
P 43.1
X
lOO. Ba, 50. 40.
Unear Subdivision X2
P43.2
Y
20.10. B. 5. 4. Ｒ ｾ
Unear Subdivision X3
P43.3
Z
1.0.8.0.5.004.0.2.
0.1 (depends on
Linear Subdivision X4
P43.4
W
grating period
set)
Angle Subdivision Xl
P44.1
X
100. 50. 25. 20.
Angle Subdivision X2
P44.2
y
la. B. 5. 4. 2.5. 2.
Angle Subdivision X3
P44.3
1. 0.4. 0.2
Z
(depends on
Angle Subdivision X4
P44A
W
line count set)
Distance Coding Xl
P45.1
X
none. 500. 1000.
Distance Coding X2
P'5.2
y
2000
Distance Coding X3
P45.3
Z
Distance Coding X4
P45A
W
(For deSCription see section 1.4.2)
For the sake of simplicity, the axis designations are assumed to be those set in
parameter P50.* (Xl=
X.
X2 = Y, X3
=
Z. X4
=
W), Xl, X2. X3, X4 are the corre-
sponding designations of the encoder inputs (see back of unit).
Factory presellings are indicated in bold type.
Technical Description
nt
Advertisement
