Advertisement
flCTUFtt.. POSITION
_
BflSIC
Plu:Fl
pIIUET
}
X
ｾ
Xl -
X
•
0.000
ｬ ｨ ｾ ｯ
)
y
-
X2
-
Y
•
0.000
ｉ ｺ Ｎ ｾ Ｂ
)
z
ｾ
X3
-
2
•
0.000
I
h;O
)
w-
X4 -.
ｾ
•
0.000
ｉ ｺ Ｎ ｾ ｯ
)
...
P"4"5 ..1
l
JJ-&
00
\\
0 _
aODDa
.
.
'"
236*02
ｾ Ｓ ｾ ｟ Ｍ
Ｌ Ｌ ｾ
"\
929 * 008·
1417-0r
I
•
<
ON
0°
..
• 0
Machine
Axis
Range Socket
Screen Display
The unit is adapted to the machine tool by means of para-
meters. These parameters are described in section 1 of the
Technical Description. The unit is delivered with preset
parameters to facilitate commissioning (see Technical
Description. section 1.2.4).
... Check whether there is a protectIVe ground for the power
connectlOO.
An
M5 threaded pm on lhe rear panel provides
an additional connection for protectrve ground.
... Connect power cable to the power
input
socket at rear of
unit and switch on power.
... Connect the KT 110 Edge Finder (available as accessory
Id.-Nr. 25102101) 10 the D-subminiature socket X10 on the
rear panel.
The
PT 850
can also
be
connected to the TS
120
Touch
Probe System (see Technical DescnptlOn. section 6).
After the reference marks have been crossed over there
should
be
no error message in the display.
If an error message is displayed. press the HELP key for more
information and then correct the error. Switch power off and
then on again .
If several errors occur at once you can display the error mes-
sages one after the other by repeatedly pressing the CE key.
Proceed in the following sequence to commission the
machine:
... SWitch on power (see section 1).
... Adjust desired screen image brightness WIth control on rear
panel.
... Select desired language. The menu fOf language selection
appears only once after initial switch-on.
... Press any key (except the HELP key).
... Choose BASIC mode of operation (see Working with the
POsmp).
... Press NO REF soft key. You need not traverse over the
reference points (ignore error messages).
... Use MOD key and the code number 95148 to access the op-
erating parameters (see Technical Descnptlon, section 1.2).
... OptimlZe operating parameters (see section 7).
... Switch power off and then on again.
... Cross over the reference marks (see Working with the
POsmp).
4
Connecting
the
KT 110
Edge Finder
6 Switch-On and
Function Check
ｾ
5
Power
Connection
Error Messages
An angle brackel for mounting the
PT 850
on a table is
available from HEIDENHAIN lld.-Nr. 25826101).
... Connect the encoders for the machine axes to the flange
sockets for encoder input on the rear panel (see illustration
on pageI1). Connect the machine axes to the l1ange sockets
according to the following table:
... Place the display unit in its intended location, The unit can
be fixed laterally to a base surface via its
M4
tapped fixing
holes
(see
illustration for dimensions).
Example:
3 Connecting
linear and
Angle Encoders
2
Mounting the
POSITIP850
12
Installation
Installation 13
Advertisement
