Erasing One Of The Remote Control Button Settings; Resetting The Remote Control Presets; Confirming Preset Codes - Pioneer VSX-LX70 Operating Instructions Manual

Controlling the rest of your system
4 Point the two remote controls towards each other
then press the button that will be doing the learning on
this receiver's remote control.
PRES KEY starts flashing to indicate the remote is ready
to accept a signal.
• The remote controls should be 3 cm to 5 cm apart.
3 cm to 5 cm
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver's remote control.
For example, if you want to learn the playback control
signal, press and hold briefly. The LCD display will
show OK if the operation has been learned.
If for some reasons the operation hasn't been learned the
LCD will display ERROR briefly and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK.
Certain buttons represent operations that cannot be
learned from other remote controls.
available are shown below (with the exception of the TV
controls, a combination of SHIFT and these buttons can
also be learned):
SYSTEM OFF
RECEIVER INPUT SOURCE
SELECT
CD CD-R HDMI
DVD TV BD TV CTRL
HOME MEDIA
ZONE2/3
DVR2 GALLERY
DVR1 i Pod TUNER RECEIVER
SLEEP DIMMER ANALOG
ATT
SR+ GENRE
D.ACCESS CLASS
DISC
CLEAR
+10
CH ENTER
LEVEL
A PARAMETER V PARAMETER
ì
TOP MENU MENU T.EDIT
TUNE
BAND ST ST
ì ì
ENTER
RETURN
SETUP
TUNE
PROGRAM
TV CONTROL
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button
you're not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components.
1
2
3
The buttons
PROGRAM
TV CONTROL
INPUT
VOL
TV VOL TV CH
SELECT
REC INFO
TV/DTV
MUTE
MPX REC STOP JUKEBOX
AUDIO SUBTITLE HDD DVD
DISP CH CH
PHOTO T.DISP
STEREO/
STATUS SIGNAL SEL SBch F.S.SURR
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
/
2 Use to select ERASE then press ENTER .
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased then press ENTER .
The LCD display flashes PRES KEY.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you're done.

Resetting the remote control presets

This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
/
2 Use to select RESET then press ENTER .
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds .
The LCD shows OK to confirm the remote presets have
been erased.

Confirming preset codes

Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
/
2 Use to select READ ID then press ENTER .
The LCD on the remote prompts you for the input source
button you want to check.
12
75
En