Settings; Display - Pioneer VSX-1014TX Operating Instructions Manual

12 Additional information

Settings

Symptom
The Auto MCACC Setup
continually shows an error.
After using the Auto MCACC
Setup, the speaker size setting
(LARGE or SMALL) is incorrect.

Display

Symptom
The display is dark or off.
After making an adjustment the
display goes off.
You can't get DIGITAL to display
when using the SIGNAL SELECT
button.
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
When playing a DVD-Audio disc,
the DVD player display shows 96
kHz. However, the receiver's
display does not.
During playback of a DTS 96/24
source, the display doesn't show
96kHz.
When playing Dolby Digital or
DTS sources, the receiver's
format indicators do not light.
When playing certain discs,
none of the receiver's format
indicators light.
When playing a disc, the
2 PL II or Neo:6 indicator lights
on the receiver.
During playback of a Surround
EX or DTS ES source on the
Extended AUTO setting, the EX
and ES indicators don't light, or
the signal is not properly
processed.
68
En
Cause
• The ambient noise level in the room is too
high, or obstacles are blocking the setup
microphone.
• There was some inaudible low-frequency
noise in the room.
Cause
• The display is set to dark or off.
• The display is set to off.
• There is a problem with the digital
connections or the digital input is assigned
incorrectly.
• The multichannel analog inputs are
selected.
• The player is paused.
• The player's sound output settings are
wrong.
• The audio from these discs is output from
the analog audio jacks of the DVD player only;
the receiver does not show the sampling rate
of the input signal through the analog inputs.
• The receiver's input signal type is set to
analog.
• No digital connection, or the digital
connection is incorrect.
• The receiver's input signal type is set to
analog.
• The DVD player is set to output Dolby Digital
and/or DTS audio as PCM.
• The disc has several playback audio tracks;
the one currently playing is actually PCM.
• The audio format of the disc is not 5.1/6.1
channel.
• The input signal type is set to analog.
• A two channel soundtrack is currently
playing.
• The soundtrack currently playing is
encoded using Dolby Surround.
•The source may be Dolby Surround EX / DTS
ES software, but it has no flag to indicate it is
6.1 compatible.
Remedy
• Keep the noise level in the room as low as possible
when using the Auto MCACC Setup (see Other problems
when using the Auto MCACC Setup on page 13 for more
on this). If the noise cannot be kept low enough, you will
have to set up the surround sound manually (page 43).
• The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto MCACC Setup.
Remedy
• Press FL. DIMMER on the remote control repeatedly to
select a different brightness.
• Press FL. DIMMER on the remote control repeatedly to
select a different brightness.
• Check your digital connections and/or assign the digital
inputs correctly (see Assigning the digital inputs on
page 60).
• Press MULTI CH IN again (see Selecting the
multichannel analog inputs on page 37).
• Press play.
• Set the player correctly (consult the manual that came
with the player, if necessary).
• This is not a malfunction. See also the operating
instructions that came with your DVD player.
• Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
• Check the digital audio connection (page 16).
• Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
• Check the settings on the player. Set the output for
Dolby Digital and DTS (no PCM conversion). See also the
operating instructions that came with your DVD player.
• Switch the playback audio channel on your DVD player.
See the operating instructions that came with your DVD
player.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• Set to Extended ON (see Using the surround back
channel (Extended mode) on page 34) then switch to the
THX Surround EX or Standard EX listening mode (see
Listening in surround sound on page 30).