ABB PGC2000 Operation And Service Manual page 10

TABLE OF CONTENTS (continued)
Title Page
SECTION 7. TEST PROCEDURES
TP 1: CARRIER, MAKEUP, AND UTILITY GAS SUPPLIES .................................................................... 7-1
TP 2: CARRIER AND MAKEUP GAS FLOW ADJUSTMENTS ................................................................ 7-1
TP 3: SAMPLE VALVE LEAKING/COLUMN FLOODING ........................................................................ 7-1
TP 4: CARRIER OR MAKEUP GAS REGULATOR ................................................................................. 7-2
TP 5: TC DETECTOR BALANCE ............................................................................................................. 7-3
TP 6: FILAMENT TCD TEST .................................................................................................................... 7-3
TP 7: COLUMN TRAIN PROBLEMS ....................................................................................................... 7-4
TP 8: BASELINE CYCLIC TEMPERATURE CONTROLLER (TCD) ........................................................ 7-5
TP 9: BASELINE CYCLIC CARRIER REGULATOR ................................................................................ 7-5
TP 10: BASELINE CYCLIC FLOW CONTROLLER ................................................................................. 7-5
TP 11: COMMON USAGE OF GASES ..................................................................................................... 7-6
TP 12: UTILITY GAS CONTAMINATION PROCEDURE ......................................................................... 7-6
TP 13: BURNER AIR CATALYTIC CLEANUP UNIT ................................................................................ 7-6
TP 14: COAXIAL CABLE .......................................................................................................................... 7-6
TP 15: FID REDUCED SENSITIVITY ....................................................................................................... 7-7
TP 16: FID WILL NOT LIGHT ................................................................................................................... 7-8
TP 17: VERIFICATION FLAME IS IGNITED ............................................................................................ 7-8
TP 18: SAMPLE VALVE ACTUATION AIR .............................................................................................. 7-9
TP 19: DOUBLE SAMPLING .................................................................................................................. 7-10
TP 20: VARIABLE SAMPLE SIZE .......................................................................................................... 7-10
TP 21: OPEN TEMPERATURE SENSOR .............................................................................................. 7-11
TP 22: SHORTED TEMPERATURE SENSOR ...................................................................................... 7-12
TP 23: LOSS OF OVEN AIR ................................................................................................................... 7-12
TP 24: ISOTHERMAL OVEN OVERTEMP SENSOR OPEN ................................................................. 7-14
TP 25: ZONE INPUT SENSOR OPEN ................................................................................................... 7-14
TP 26: OPEN OR SHORTED HEATER ................................................................................................... 7-15
TP 27: OPEN FUSE TO AC CONDITIONING BOARD .......................................................................... 7-16
TP 28: FID POLARIZING VOLTAGE TEST ............................................................................................ 7-16
TP 29: "FLAME OUT" LED REMAINS ON AFTER FID FLAME IGNITION ............................................ 7-17
TP 30: CHECKING TEMPERATURE TABLE VALUES ......................................................................... 7-19
TP 31: PLUGGED JET OR BREATHER ................................................................................................ 7-24
TP 32: PEAK DISCRIMINATION ............................................................................................................ 7-25
TP 33: CHECKING METHOD TABLE CONFIGURATION ..................................................................... 7-26
TP 34: VENT BACK PRESSURE ........................................................................................................... 7-30
TP 35: PRINTER TEST ........................................................................................................................... 7-31
TP 36: RESIDUAL SAMPLE ................................................................................................................... 7-31
TP 37: TREND OUTPUT ........................................................................................................................ 7-31
TP 38: DIGITAL I/O PCB ........................................................................................................................ 7-33
TP 39: LOW CARRIER PRESSURE ...................................................................................................... 7-33
TP 40: LOW SAMPLE FLOW HARDWARE ALARM .............................................................................. 7-34
TP 41: PROGRAMMED TEMPERATURE OVEN COOL DOWN ........................................................... 7-34
TP 42: STREAM SWITCHING ................................................................................................................ 7-36
TP 43: FPD GAIN SETTING .................................................................................................................... 7-37
TP 44: FPD FLAME WILL NOT LIGHT .................................................................................................... 7-38
TP 45: "FLAME OUT" LED REMAINS ON AFTER FPD FLAME IGNITION ........................................... 7-39
viii 2000-OSM, F1